Penner Pacific Guida
Pacific Recumbent Height
Adjustable Bath 1
PACIFI
C
Recumbent Height-Adjustable
Bath System 9700 & Still Bath
PENNER MANUFACTURING, INC
Box 523 / 102 Grant St.
Aurora, NE 68818
1-866-PENNERS 1-866-736-6377 1-800-732-0717
390745 Revision C 03/01/2008
Installation / Assembly Instructions
Pacific Recumbent Height
Adjustable Bath 2
Table of Contents
Table of Contents 2
Introduction 3
Terminology and Symbols Meanings 3
Room Size Requirements 4
Hot & Cold Water Supply Requirements 4
Rough-In Requirements 5
Pacific Bath Aqua-Aire Controls & Descriptions 6
Pacific Bath Still Bath Controls & Descriptions 7
Unpacking and Assembling the Pacific Bath 8
Electrical Requirements 15
Electrical Connection of the Pacific Bath 15
Finishing up 17
Pacific Recumbent Height
Adjustable Bath 3
Introduction:
These instructions are for the installation of a Pacific Recumbent
Height Adjustable Bathing System 7900 Bath Panel and Bath Shell or
Tank. This system is shipped on two pallets. The Pacific Bath Shell or
Tank attaches easily to the Pacific Bath Panel. This system is a height
adjustable tub.
Terminology and Symbols Meanings:
When the terms “left” or “right” are used with reference to the tub, this
means left or right as you look facing the control panel.
Meaning: Safety warning. Failure to understand and obey this
warning may result in injury to you or to others.
Meaning: Failure to follow these instructions
may cause damage to parts or systems.
Note: Refer to the “Pacific Bath Controls” section of this manual, page
6, for the location of any of the controls referenced.
NOTE: It is required that a licensed plumber make all plumbing
connections. He can select the best method of connection and if
Reduced Pressure Zone Backflow Preventers are required.
Drain Requirements:
The Pacific Bath is equipped with a 1½” (inside) diameter flexible
drain tub to enable drain attachment on the floor directly under the
tank or route through the panel frame and attach to a wall drain.
Figure 2 shows two different options for roughing in the drain pipe –
from the floor or from the wall. The rough-in needs to be 1½” (outside
diameter).
CAUTION
Pacific Recumbent Height
Adjustable Bath 4
Suggested Rough-Ins
Space Requirements:
See Figure 1 for “Recommended Room Size” requirements
Figure 1
Room Size Requirements
Hot and Cold Water Supply Requirements:
3/4” supply lines with on/off valves with 3/4” NPT female threads. We recommend
3/4” ball valve with 3/4” NPT female ports. Valves supplied by others. See Figure 2
for recommended locations.
For optimum performance, dynamic pressures should be nominally equal.
Maximum static supply pressure: 145 PSI.
Maximum dynamic/maintained supply pressure: 81 PSI.
Maximum supply hot water temperature: Consult local requirements for maximum
allowed supply temperatures. (Not recommended over 110oF)
Pacific Recumbent Height
Adjustable Bath 5
Rough-In Requirements
Figure 2
Recommended water supply rough-in’s (wall or floor) and
drain rough-in’s (wall or floor)
Pacific Recumbent Height
Adjustable Bath 6
Pacific Bath Control Panels
Figure 3, 4 & 5
1. Temperature Control Knob (Fill/Shower)
2. Fill/Shower Water-Temperature Readout
3. Tub-Temperature Readout
4. Tub Fill ON / AUTO OFF Button
5. Tub Fill OFF Button
6. Tub Height Up Button
7. Tub Height Down Button
8. Pump or Aqua-Aire ON/OFF Button
9. Rinse Jets Button (On tubs with Aqua-Aire only, Push and Hold)
10. Disinfect Hand Spray Button (On/Auto Off)
11. Disinfect Jets Button (Push and Hold)
12. Hand Shower On/Auto Off (The unit has an adjustable time automatic shut-off)
13. Bath Oil Pump Plunger
14. Shampoo Pump Plunger
1.
2.
4.
3.
5.
6.
8.
7.
9. 12.11.10. 13. 14.
Pacific Recumbent Height
Adjustable Bath 7
Pacific Still Bath Control Panels
Figure 7
1. Temperature Control Knob (Fill/Shower)
2. Fill/Shower Water-Temperature Readout
3. Tub-Temperature Readout
4. Tub Fill ON / AUTO OFF Button
5. Tub Fill OFF Button
6. Tub Height Up Button
7. Tub Height Down Button
8. Disinfect Hand Spray Button (On/Auto Off)
9. Hand Shower On/Auto Off (The unit has an adjustable time automatic shut-off)
10. Bath Oil Pump Plunger
11. Shampoo Pump Plunger
1.
2.
4.
3.
5.
6.
7.
8.
11.
10. 9.
Figure 6
Figure 8 Figure 9
Pacific Recumbent Height
Adjustable Bath 8
Unpacking and Assembling the Pacific Bath
Note: Your Pacific system is shipped in two separate boxes on pallets labeled
Pacific Panel and Tub Shell.
1. Upon receipt of your Pacific System inspect both boxes for externally damaged
and evidence of abuse. If any is observed note it on the packing slip and report
it to the freight company.
2. Take the cardboard box off of both pallets.
3. The tub shell, when removed from the pallet, is light and can be carried from
the pallet into the area of installation. Remove the legs and hardware package
included in the tub shell box.
4. The Panel is left on the pallet until located in the area of installation. This
pallet is 36” wide and will only fit through a 36” door. Move the pallet, with the
Pacific panel on it, to the installation area by using appropriate dollies to avoid
damage to the floor. Figures 10 & 11
IMPORTANT: DO NOT UNCRATE THE
PACIFIC PANEL & TUB SHELL BEFORE
READING THESE INSTRUCTIONS. FAILURE
TO FOLLOW THESE INSTRUCTION
COULD RESULT IN AN INJURY TO THE
INSTALLER OR DAMAGE TO THE PACIFIC SYSTEM.
Pacific Recumbent Height
Adjustable Bath 9
5. On the Panel pallet, remove the two wooden plates that
secure the panel base to the Pacific pallet and discard.
(See Figure 12 below)
6. Assemble both legs, extending forward, onto the base of the
Pacific panel using the 4 ea. ½-13 bolts included in the
installation kit. You will need a ¾” socket for the bolts.
(See figure 13 & 14 above)
Unpacking and Assembling the Pacific Bath
Figure 14
Figure 12 Figure 13
Pacific Recumbent Height
Adjustable Bath 10
7. With the Pacific Panel still on the pallet, and the legs installed, two
people can easily slide the whole panel forward on the pallet
pulling on the legs until the front of the panel base is flush with the
front edge of the pallet. Then let the legs rest on the floor by
tipping the panel forward. (See figure 15 & 16)
Figure 15 & 16
CAUTION:
Do not slide the panel too far forward on the pallet. Failure to do
so may result in the panel tipping and may damage the unit.
8. You are now ready to remove the Pacific Panel from the Pallet.
You must follow these specific steps to allow the Pacific Panel to
power itself off of the pallet.
WARNING:
Always have two people to ensure the panel stays stable as it is
lowered from the pallet. Failure to follow these instructions could
result in an injury to the installers or damage the Pacific System.
Unpacking and Assembling the Pacific Bath
Indice
Altri manuali Penner Vasca idromassaggio
