Pensonic PSF-46S Manuale utente
STAND FAN
PSF-46S
INSTRUCTION
MANUAL
CONTENTS
Title Page No.
Parts Introduction 1
Technical Specifications 1
Before Using 1
How to Assemble Stand Fan 2
How to Use Stand Fan 2
Cleaning and Maintenance 2
Important Guidelines 2 –3
Thank you for choosing PENSONIC appliances. May you have an enjoyable experience using our
products.
Parts Introduction
1. Hook
2. Front Guard
3. Fixing Screw
4. Clip
5. Fan Blade Knob
6. Fan Blade
7. Guard Interlocking Nut
8. Rear Guard
9. Speed Knob
10. Oscillation Knob
11. Motor
12. Cord Set
13. Screw
14. Height Adjustment Knob
15. Base
16. Molded Securing Knob
Technical Specifications
Voltage
220-240V~
Wattage
60W
Frequency
50Hz
Blade Size
16” (400mm)
Before Using
Please read these instructions carefully before use and keep them for future reference.
Check your local main voltage whether it is the same as stated on the appliance.
Before using for the first time, remove any protective films or stickers from the table fan.
Ensure the power switch is at the off position.
1
2
3
4
8
9
10
11
12
13
14
15
16
5 6 7
1
How to Assemble Stand Fan
Attach the rear guard to the front side of the motor; fasten the guard interlocking nut by turning
it clockwise until the guard is secured firmly in place.
Mount the fan blade onto the motor shaft; fasten the blade knob by turning anti-clockwise
firmly.
Installing the front guard:
- Open the front guard clip and attach the hook to the rear guard.
- Push the round edges of front guard to fit it securely into the rear guard.
- Lock the clip.
Installing the base:
- Insert the stand body to the base unit firmly. Reverse the whole unit and secure the stand
body by fitting the molded securing knob from the bottom of the base unit.
- Connect and fix the fan body to the stand body.
- Ensure the stand body is completely interlocked with the base unit.
- Insert the panel to the stand body and lock it into position by turning the panel screw
clockwise. Loosen the height adjustment knob to extend the extension tube to the required
height and then tighten the securing knob.
How to Use Stand Fan
Connect the plug into a power supply socket and switch on the power.
Switch on the fan by turning the speed button at any of the “3”, “2” or “1” settings.
Turn the “3”, “2” or “1” button to adjust the fan speed from High-Medium-Low.
To stop the fans, turn the speed knob the off position.
To tilt the fan, always ensure that the fan is in off position and wait until the blade has
completely stopped for safety reasons. Hold the stand firmly with one hand and move the guard
gently upwards or downwards.
The oscillation knob is positioned at the top rear side of the motor housing. Press the knob
down to make the fan oscillate or pull it up to stop the oscillation.
To adjust the height of fan, always ensure that the fan is at off position and wait until the blade
has completely stopped for safety reason. Hold the stand firmly and loosen the height
adjustment knob, then push down or pull up the extension tube to adjust the fan height.
Cleaning and Maintenance
Always unplug the product from the wall socket and shut down completely prior to cleaning.
Do not use abrasive sponge, scouring pads or stiff brush to clean the appliance.
Please be cautious when cleaning the product near to the motor housing area.
Use only damp cloth to wipe the exterior surfaces of the unit. Do not immerse the main body in
water.
Do not allow the motor or other electrical components to be exposed to water.
For proper storage, always place the fan in a low humidity environment.
Important Guidelines
Use only original accessories supplied.
The current voltage which indicates on the plate must correspond to your local voltage.
2
The fan should be operated only on condition that the type of power supply corresponds to the
marking label. Otherwise, it will not work or even be damaged.
Never use unit unless it is fully assembled.
Do not overload outlets or extension cords. It can result in fire or electric shock.
Do not operate the appliance if the power supply cord or plug has been damaged.
This fan is intended for indoor and household use only; not for outdoor, commercial and
industrial use.
Do not immerse the cord, plug or appliance in water or other types of liquid and do not pour
water onto it to avoid from fire, electrical shock or personal injury.
To protect against risk of electrical shock, do not force any foreign objects such as pins and
wires into any openings.
Do not pull the cord to remove the plug from wall socket, pull on the plug instead.
Do not attempt to insert or remove the plug with wet hands.
Do not place the appliance on or near hot gas/electric burner, or a heated oven.
Do not let cord hang over the edge of table or counter or touch any hot surfaces.
In the event not using the appliance for a long period of time, please remove the plug from the
power outlet.
Do not allow the motor or other electrical components to be exposed to water.
Never let children use electrical equipment without adult supervision.
Educate children about the danger and safety rules associated with operating electrical
equipment.
This appliance should not be used by the physically challenged, slow response or mentally
disabled people (including children) unless guidance is provided during operation.
Do not operate any appliance with a damaged cord or plug, or after the appliance malfunctions
or has been damaged in any manner. Repair and services should always be carried out by
PENSONIC Customer Care/Service Centre.
3
Indice
Altri manuali Pensonic Fan
