Pentax MZ-7 QUARTZ DATE Manuale utente

27550 1/9

[ INDEX ]

Page

[DISASSEMBLY & ASSEMBLY PROCEDURES] .................................................................................2

OUTLINE

...........................................................................................................................................2

1. COSMETIC PARTS ......................................................................................................................................2

2. SOLDERING OF THE MAIN BODY.............................................................................................................3

3. MAIN P. C. BOARD (0-T100)...................................................................................................................4

4. MAIN BODY...............................................................................................................................................4

* Soldering position of lead wires for Winding motor (0-S200)......................................................4

5. TOP COVER (0-A301)...............................................................................................................................5

5-a. Arrangement of the reverse side of the Top cover.....................................................................5

5-b. Flash case (Q2)................................................................................................................................5

5-c. [Adjustment & Confirmation] Installing position of the Pop-up magnet (G119).....................6

5-d. [Confirmation] Retraction of the Flash..........................................................................................6

6. ADJUSTMENT & CONFIRMATION.............................................................................................................6

6-1. Function check..................................................................................................................................6

6-2. Adjustment with the Programmed software..................................................................................7

6-3. Position of the Light sensor...........................................................................................................7

[DATA TABLE]..............................................................................................................................................8

1. BATTERY LIFE ...........................................................................................................................................8

2. BATTERY CONSUMPTION CURRENT..........................................................................................................8

[TABLE OF JIGS, TOOLS AND TESTERS] .........................................................................................8

* THE TOOL FOR FLASH POP-UP..................................................................................................................9

2/9 27550

186

[Disassembly & Assembly procedures]

Outline

The disassembly and assembly procedures of MZ-7 are similar to the MZ-5 and MZ-10.

The only exclusive notice of assembly for MZ-7 is mentioned below.

For others, refer to the Service manual of MZ-5 and MZ-10.

1. Cosmetic parts

[Disassembly procedures]

1-1. Flash pop-up

To remove the top cover, insert the battery and push the flash pop-up button.

In case of the power line of the camera is defected, use the hand-made tool to pop-up the

flash

1-2. Bottom cover (A401), Back cover

7 screws (A181, A187 x6), Battery cover (0-A402)

1-3. Top cover (0-A301) and Front cover

1) 8 screws for top cover

A186, A187 x2, A188 x2, A190,

TY-CNL-D 1.7x8.0(Ni), TY-CNL-D1.7x8.0

2) Discharging the Main capacitor

Lift up the top cover slightly and discharge.

The blue lead wire (Xe+) on Flash PCB

The bayonet mount retainer screw (GND)

3) Front cover (A102, A153), Grip (A150)

[Note for assembly]

Set Focus mode lever (A131)

and AF-SW at “AF” position.

*In case of replacing A131(=27250-A131),

cut the positioning stud of reverse side

of A131. (Early production model)

4) Unsolder 7 lead wires and 3 FPC (T51, 0-T20, 0-T57) come from

top cover

[Note of assembly]

1) Solder wires and FPC in order of Orange and Yellow (G119), T51, 0-T20, 0-T57,

Black (A330) and lead wires from Q100

2) Arrange lead wires of Q100 (Green, Blue, Brown, and Black) and Black (A330).

(Same as MZ-10)

3）Install A186 screw before retract the flash.

①

②

27550 3/9

DT(3x7)

Red(A36)

Blk(A37) 2 lands(I210)

Ye(C18)

Br(0-S200)

Pu(C18)

R(A35) Pi(0-S200)

2 lands 4 lands(0-Q201)

Gray(0-Q201)

DT(10x6)

2. Soldering of Main body

[Disassembly procedure]

2-1. Switch the panorama lever to “Full frame”

2-2. Remove the LCD….TY-CNL-D1.7x5.0

2-3. Around the release SW (Refer to the figure below)

8 lead wires, 8 soldering lands

[Note of assembly]

Arrange lead wires as below. ( )

2-4. Top of the film chamber

[Note of assembly]

Position the FPC at correct place and fix with DT (4x10).

2-5. Soldering

2 lead wires of N300 (Red and Black, Unsolder at FPC of G100).

Soldering lands : 4 FPC (T81, T301, T61, T64), DX contact (R110)

[Note of assembly] After soldering, put T81 FPC aside of mirror box.

2-6. Base plate (O205)

1) Battery contact piece (-) (A34)

3) TY-CNL-D1.7x4.0, Lift up O205.

2-7. Eyepiece frame (M301)

2 screws

2-8. Main body and Front housing

6 screws, A162

[Note of assembly]

While paying attention to the lead wires and FPC, install the Front housing with the Main body.

The Mechanical back (Standard : 45.46 mm±0.02 (Same as MZ-5)

4/9 27550

3. Main P. C. Board (0-T100)

[Note of assembly]

3-1. When the viewfinder LCD is installed,

push the LCD to the direction of allow mark.

(Same as MZ-10)

3-2. Stick the tape (DT, PT and BT) as shown in the figure.

4. Main body

[Note of assembly]

The soldering position of winding motor (0-S200)

The length of the lead wire is different from MZ-5. In case of 0-S200 is replaced, lead wires

should also be replaced.

Pink (65mm) 0-S200

Brown (65mm)

Ground (GND) mark

27550 5/9

5. Top cover (0-A301)

[Note of assembly]

When assembling the top cover, refer to the Parts list and figures below.

The type of the Hot shoe cover should be “FK” type for MZ-7. (The other type may activate

the switch (A329) and result the Flash won’t pop-up.)

5-a. Arrangement of the reverse side of top cover

DT (7x10) 0-T57

DT (5x7) 0-T20

DT (4x10) T60

*Arrangement of Q100’s lead wires *Center part of top cover

0-A373 0-A365

Black Brown Blue Green (Q100) 0-A368

Bond

Gray Orange G119

5-b. Flash frame (Q2) Blue

Apply silicon

(4 points) From top, Green, Brown,

Green Black and Blue

Q3 (Adj.) Bond

6/9 27550

0-A373

5-c. [Adjustment & Confirmation] Installing position of Pop-up magnet (G119)

1) At the flash pop-up condition, the armature of G119 should be

positioned as shown in figure right.

2) Loosen Q3 installing screw and tight again. (Refer to figure in front page)

3) At the flash retracted position, when the armature lever (0-A373) is

pushed toward the back and released, the flash should be pop-up.

4) After adjustment and confirmation above, apply screw lock to G119, retainer screw and

2 portion of positioning studs.

5-d. [Confirmation] Retraction of the Flash

Confirm after installing the Flash cover (Q1).

1) At the retracted position, there should be approx. 0.1mm play when Q1 is pushed down

toward as the arrow mark.

2) The flash should not pop-up when the side of Q1 is pushed gently.

[Adjustment]

The choice of thickness or using quantity of Q3

Q3-00A (t=0.2), -00B(t=0.1), -00C(t=0.15)

6. Adjustment and confirmation

The adjustment and confirmation as follow are same as MZ-5.

* Exposure and DX code

* AF check (Except Power zoom function)

* Mechanical back (Standard : 45.46 mm ±0.02)

* Mirror function

* Position of 1st and 2nd mirror

6-1. Function check

The exclusive function for MZ-7.

1) Set the mode dial at AUTO PICT and FA(F) lens at “A” position.

When the main switch is turned on, the LED of the mode dial should light up in order as

follow.

→ → → → → → →AUTO PICT

2) The LED of the mode dial should correspond as accordingly to the position of the mode dial.

(Continue to next page)

27550 7/9

3) Remote control mode – Select the mode ( ) by the drive button ( )

The self-timer LED should flash, and the shutter should be released by the transmitter.

4) Set the mode dial at “Tv” and operate the select lever, Tv and Av display should be changed.

The Bar Graph in the viewfinder should be displayed when the Side button is pressed, and

the 1/30 or slower speed should be displayed by orange color. (With FA(F) 50 mm lens)

5) The ISO film speed and PCV Beep tone should be able to selected by the select button at

the “ISO” or ( ) position of the mode dial.

6) At the AUTO PICT mode and MF(AF-SW) mode, cover the front of the lens by hand, and

press the shutter button half way, the flash should pop-up automatically and the back light

on the external LCD panel should light up.

At the “AF” mode, cover the front of the lens by hand, and press the shutter button half

way, the flash should be fired continuously to help the focusing.

7) When the flash button ( ) is pressed, the flash should pop-up and the Auto-flash mark

( ) should be off

At the Red-eye reduction mode ( ), the flash should be fired twice.

6-2. Adjustment with the programmed software

27550 programmed soft (Exclusive use)

The other items and the method of connection are same as MZ-5.

1) The method of adjustment is same as MZ-5.

2) The positioning of AF frame (Viewfinder) and AF sensor and AF chart are same as MZ-10.

6-3. Position of the Light sensor

1) The method of adjustment is same as MZ-5.

2) The position is a same as MZ-10. (Refer to the figure below)

0.5mm±

±±

±0.5mm/actual size

（0.0〜+1.0mm）

Center of the Light sensor

Center of the AF frame

AF frame

3.4

8/9 27550

[Data table]

1. Battery life

Condition/Temperature 20℃/68°F-10

℃/14°F

Without flash Approx. 120 rolls Approx. 30 rolls

With 50% flash Approx. 20 rolls Approx. 15 rolls

With 100% flash Approx. 12 rolls Approx. 5 rolls

Exposure time at the Bulb mode Approx. 8 hours Approx. 2 hours

* 24 exposure roll of film, with new CR2 battery

2. Battery consumption current

Main swittch OFF (Back cover close) 50μA or less

Main Switch ON (Meter Sw OFF)

With FA lens

With F or A or M lens

Without lens

280μA or less

260μA or less

250

μA or less

Meter switch ON 120 mA or less

Exposure (Bulb) 150 mA or less

AF motor operating (Average) 700 mA or less

Rewinding 500 mA or less

*With regulated DC power supply, set at 5.5V (More than 3A)

[Jigs, tools and testers]

◎ Exclusice use for 27550

1. Programmed software

PC/AT compatible, 3.5 inch (SD Ver.3.1 or later) No.95901-P274

PC98 (NEC or EPSON) 3.5 inch (ND Ver3.1 or later）No. -P084

PC98 (NEC or EPSON) 5.0 inch (ND Ver3.1 or later) No. -P184

2. Flash pop-up jig (Hand-made)

*To use for pop-up the flash with out power (electricity)

The way of making and dimensions are shown in next page.

◎ Others

Interchangeable with MZ-5. Refer to the Service manual of MZ-5.

27550 9/9

①

②③

*Flash pop-up jig

[Material] Telephone-card or equivalent, which can be inserted between flash, cover and top cove

1.The way of making (Size and shape are just for the reference)

1) Cut the card as below. (Fig.1)

2) Cut the corner as below. (Fig.2)

①②

③④

Fig. 1 (Ex.: 4 pcs.）

2. How to use

Fig.2

Altri manuali per MZ-7 QUARTZ DATE

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali Pentax Macchina fotografica digitale

Pentax

Pentax ZOOM 105-R Manuale utente

Pentax

Pentax Optio W20 Manuale utente

Pentax

Pentax PC-555 DATE Manuale utente

Pentax

Pentax OPTIOA20 - Optio A20 Digital Camera Manuale di istruzioni

Pentax

Pentax K-7 Guida rapida

Pentax

Pentax 35 II Manuale utente

Pentax

Pentax Optio P70 Manuale utente

Pentax

Pentax Optio M50 Manuale utente

Pentax

Pentax WG-90 Guida

Pentax

Pentax Model Optio S60 Manuale utente

Pentax

Pentax Optio RZ10 Manuale utente

Pentax

Pentax IQZoom 105SW / IQZoom 120SW Manuale utente

Pentax

Pentax OPTIO S Manuale utente

Pentax

Pentax Optio W90 Manuale utente

Pentax

Pentax ILX Manuale utente

Pentax

Pentax Optio WG-1 GPS Gray Manuale utente

Pentax

Pentax OPTIOA20 - Optio A20 Digital Camera Manuale utente

Pentax

Pentax Optio H90 Orange Manuale utente

Pentax

Pentax KC-01 Manuale utente

Pentax

Pentax efina Manuale utente

Pentax

Pentax L Manuale utente

Pentax

Pentax K 100D Super Manuale utente

Pentax

Pentax PC-300 DATE Manuale utente

Pentax

Pentax K 100D Super Manuale utente

Manuali Macchina fotografica digitale popolari di altre marche

Mercury

Mercury 350K Manuale utente

Sanyo

Sanyo VPC-S1085 Manuale utente

GE SMART A1255 Manuale utente

Point Grey

Point Grey Gazelle Manuale utente

Nikon

Nikon COOLPIX A Manuale utente

BlazeVideo

BlazeVideo A280 Manuale utente

Sony

Sony MCA-20 Manuale utente

Sony

Sony Alpha DSLR-A290 Manuale utente

ATIK Cameras

ATIK Cameras One Manuale utente

CohuHD Costar

CohuHD Costar 3930 Series Manuale utente

Leica

Leica M10-R Manuale utente

FujiFilm

FujiFilm FinePix A700 Manuale utente

Lorex

Lorex LNZ81P25 Series Manuale utente

GE J1470S Manuale utente

Sony

Sony A6700 Guida utente

Canon

Canon EOS ELAN7 Manuale utente

Nikon

Nikon Coolpix 100 Manuale utente

Samsung

Samsung SCC-C4253 Manuale utente