peplink SD Manuale utente
Peplink SD Switch User Manual
Published on October 25th, 2018
Table of Contents
Switch Layout 3
Specifications 4
Hardware Overview 5
Quick Start Functions 6
Reset switch 6
Connect Ethernet 6
Connect SFP+ 6
Connect to Management Port 6
Connect to Console Port 7
InControl Configuration 7
Add switch to InControl 7
Enable InControl Cloud Management 9
Configuring VLANs 10
Define a new VLAN 12
Default VLAN settings 13
InControl Device Details 14
Port List 16
Port details and configuration 18
Port List 19
LACP - Link Aggregation 21
InControl Reports 22
InControl Clients 22
InControl Settings 23
Settings > Remote Web Admin 23
Settings > Firmware Management 23
Stand Alone Configuration 24
Standalone menu options > Dashboard 25
Standalone menu options > Configure > Network Settings 27
Standalone menu options > Configure > Interfaces > Switch Ports 28
LACP (802.3ad) configuration 30
Standalone menu options > System > Admin Security 31
Standalone menu options > System > Firmware 33
Standalone menu options > System > Time 34
Standalone menu options > System > Schedule 34
Establish a Scheduling Profile 34
Standalone menu options > System > Email Notification 36
Standalone menu options > System > Event Log 37
Standalone menu options > System > SNMP 37
Standalone menu options > System > InControl 39
Standalone menu options > System > Configuration 40
Standalone menu options > System > Reboot 41
Standalone menu options > System > Tools 41
Ping 42
Traceroute 42
Wake-on-LAN 43
Standalone menu options > Status > Device 43
Standalone menu options > Status > Client List 44
Standalone menu options > Status > Event Log 45
Switch Layout
Specifications
SD Switch
LAN Interface
24x 10/100/1000 802.3at (PoE+) enabled
GbE ports, 2 x SFP+ ports
Switching Capacity
88 Gbps
Max. Packet Forwarding rate
66 Mbps
MAC Address Table Size
24K
VLAN Groups
Yes
Fiber Module
10 Gbps
Power Input
2 or 3x 100V - 240V AC Input (depending on
model) , with power redundancy
Power source
2 or 3x PSU
Power Consumption
50W System, 550W or 850W P0E+
PowerBudget
Dimensions
19.1 x 15.7 x 1.7 inches
485 x 400 x 45 mm
(L x W x H)
Weight
17.6 pounds
8.0 kg
Operating Temperature
32° - 104° F
0° - 40° C
Humidity
15% - 95% (non-condensing)
Warranty
1-Year limited Warranty
Hardware Overview
Front Panel Port LED
Port
LED
State
Status
PSU
No PoE
MGMT
IEEE 802.3a?
Port
LED
State
Status
Console
RJ45 1-24
poe /speed/link/act
off/green/orange
Link established
(flashing indicates
network activity)
SFP+ 1-2
Quick Start Functions
Reset Switch
With a paperclip, press and hold the reset button for at least 10+ seconds, until all the lights light
up.
(If you press and hold the reset button for only 5-10 seconds, instead of a factory reset, the
admin user password will be reset to ‘admin’ and access will be reset to HTTP)
Connect Ethernet
Connect an RJ45 cable from an Internet-enabled router to any RJ45 port on the Peplink SD
Switch.
Connect an RJ45 cable from any client device to port 1-24 of the Peplink SD Switch.
Connect SFP+
Remove the protective plastic cover from the SFP+ port.
Plug a compatible fiber module into the SFP port.
Compatible SFP+ modules are: QUESTION!
Connect to Management Port
The management port is designed for Out-of-Band management.
The SD-Switch can be managed via this port only by default.
The management Port IP address is 192.168.1.254/24
Connect a RJ45 to the management port and a client device.
Configure the client device with an IP address in the 192.168.1.0/24 range.
Open a web browser and enter the default IP address of the management port in the address
field of the web browser ( http:\\192.168.1.254) to access the web interface of the Peplink
Switch.
Login with the default credentials:
Username: admin
Password: admin
(This is the default admin user login of the Peplink Balance. The admin and read-only user
password can be changed at System>Admin Security.)
Connect to Console Port
Access the SD-Switch via this port with CLI to get the status and info of the switch.
This is currently under development.
InControl 2 Configuration
There are two ways to configure the Peplink Switch.
Through InControl 2, Peplink’s cloud-based device management and monitoring application, or
through the web admin interface.
This section describes an overview of the InControl 2 settings and information specific to the
Peplink Switch.
For a complete overview of InControl 2 options, please refer to our InControl 2 documentation.
Add Switch to InControl 2
1: Logon to InControl 2 and create a separate group for your Peplink switch.
Add the switch serial number and follow the onscreen instructions.
2: Connect an active ethernet connection to one of the numbered switch ports 1 to 24.
3: The Switch will show online in InControl 2 (the marker on the map will change from red to
green).
Enable InControl 2 Cloud Management
InControl 2 management needs to be enabled to allow the Peplink Switch to be configured
through InControl 2.
This setting is enabled by default.
The settings can be changed in the local web interface of the Switch.
In Incontrol 2, browse to the Device Details page.
Select: Settings > Remote Web Admin to connect to the Switch local web interface.
Indice
Altri manuali peplink Interruttore
