Pepperl+Fuchs HiD2872 Manuale utente
ISO9001
2
3
Functional Safety
Solenoid Driver
HiD2872, HiC2873(Y1),
HiD2876, HiC2877
PROCESS AUTOMATION
MANUAL
With regard to the supply of products, the current issue of the following document is applicable:
The General Terms of Delivery for Products and Services of the Electrical Industry, published by the
Central Association of the Electrical Industry (Zentralverband Elektrotechnik und Elektroindustrie (ZVEI) e.V.)
in its most recent version as well as the supplementary clause: "Expanded reservation of proprietorship"
Functional Safety HiD2872, HiC2873(Y1), HiD2876, HiC2877
Functional Safety HiD2872, HiC2873(Y1), HiD2876, HiC2877
Content
2019-07
3
1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
1.1 Content of this Document. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
1.2 Safety Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
1.3 Symbols Used . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
2 Product Description. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
2.1 Function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
2.2 Interfaces . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
2.3 Marking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
2.4 Standards and Directives for Functional Safety . . . . . . . . . . . . . . . . . . 9
3 Planning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
3.1 System Structure. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
3.2 Assumptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
3.3 Safety Function and Safe State . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
3.4 Characteristic Safety Values . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
3.5 Useful Lifetime . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
4 Mounting and Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
4.1 Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
5 Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
5.1 Proof Test . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
6 Maintenance and Repair . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
7 List of Abbreviations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
2019-07
4
Functional Safety HiD2872, HiC2873(Y1), HiD2876, HiC2877
Introduction
1 Introduction
1.1 Content of this Document
This document contains information for usage of the device in functional safety-related
applications. You need this information to use your product throughout the applicable stages
of the product life cycle. These can include the following:
• Product identification
• Delivery, transport, and storage
• Mounting and installation
• Commissioning and operation
• Maintenance and repair
• Troubleshooting
• Dismounting
• Disposal
The documentation consists of the following parts:
• Present document
• Instruction manual
• Manual
• Datasheet
Additionally, the following parts may belong to the documentation, if applicable:
• EU-type examination certificate
• EU declaration of conformity
• Attestation of conformity
• Certificates
• Control drawings
• FMEDA report
• Assessment report
• Additional documents
For more information about Pepperl+Fuchs products with functional safety,
see www.pepperl-fuchs.com/sil.
Note!
This document does not substitute the instruction manual.
Note!
For full information on the product, refer to the instruction manual and further documentation
on the Internet at www.pepperl-fuchs.com.
Functional Safety HiD2872, HiC2873(Y1), HiD2876, HiC2877
Introduction
2019-07
5
1.2 Safety Information
Target Group, Personnel
Responsibility for planning, assembly, commissioning, operation, maintenance,
and dismounting lies with the plant operator.
Only appropriately trained and qualified personnel may carry out mounting, installation,
commissioning, operation, maintenance, and dismounting of the product.
The personnel must have read and understood the instruction manual and the
further documentation.
Intended Use
The device is only approved for appropriate and intended use. Ignoring these instructions
will void any warranty and absolve the manufacturer from any liability.
The device is developed, manufactured and tested according to the relevant safety standards.
Use the device only
• for the application described
• with specified environmental conditions
• with devices that are suitable for this safety application
Improper Use
Protection of the personnel and the plant is not ensured if the device is not used according
to its intended use.
2019-07
6
Functional Safety HiD2872, HiC2873(Y1), HiD2876, HiC2877
Introduction
1.3 Symbols Used
This document contains symbols for the identification of warning messages
and of informative messages.
Warning Messages
You will find warning messages, whenever dangers may arise from your actions.
It is mandatory that you observe these warning messages for your personal safety and in order
to avoid property damage.
Depending on the risk level, the warning messages are displayed in descending order
as follows:
Informative Symbols
Action
This symbol indicates a paragraph with instructions. You are prompted to perform an action
or a sequence of actions.
Danger!
This symbol indicates an imminent danger.
Non-observance will result in personal injury or death.
Warning!
This symbol indicates a possible fault or danger.
Non-observance may cause personal injury or serious property damage.
Caution!
This symbol indicates a possible fault.
Non-observance could interrupt the device and any connected systems and plants,
or result in their complete failure.
Note!
This symbol brings important information to your attention.
Functional Safety HiD2872, HiC2873(Y1), HiD2876, HiC2877
Product Description
2019-07
7
2 Product Description
2.1 Function
General
This isolated barrier is used for intrinsic safety applications.
The device supplies power to solenoids, LEDs and audible alarms located in
a hazardous area.
The output signal has a resistive characteristic. As a result the output voltage and current
are dependent on the load.
Line fault detection of the field circuit is indicated by a red LED and an output on the fault bus.
HiD2872
This device is a 2-channel device.
The device is loop powered or bus powered.
It is controlled with a loop powered control signal, switch contact, transistor, or logic signal.
At full load, 12 V at 40 mA (with 55 mA current limit) is available for the hazardous
area application.
An alternative low current output is available for driving a single LED without installing
an external current limiting resistor.
This device mounts on a HiD Termination Board.
HiC2873
This device is a 1-channel device.
The device is loop powered or bus powered.
It is controlled with a loop powered control signal, switch contact, transistor, or logic signal.
At full load, 12 V at 40 mA (with 55 mA current limit) is available for the hazardous
area application.
This device mounts on a HiC termination board.
2019-07
8
Functional Safety HiD2872, HiC2873(Y1), HiD2876, HiC2877
Product Description
HiC2873Y1
This device is a 1-channel device.
The device is bus powered.
The device is controlled with a switch contact, transistor, or logic signal.
At full load, 12 V at 40 mA (with 55 mA current limit) is available for the hazardous
area application.
This device mounts on a HiC termination board.
HiD2876
This device is a 2-channel device.
The device is loop powered or bus powered.
It is controlled with a loop powered control signal, switch contact, transistor, or logic signal.
At full load, 11.2 V at 40 mA (with 55 mA current limit) is available for the hazardous
area application.
An alternative low current output is available for driving a single LED without installing
an external current limiting resistor.
This device mounts on a HiD Termination Board.
HiC2877
This device is a 1-channel device.
The device is loop powered or bus powered.
It is controlled with a loop powered control signal, switch contact, transistor, or logic signal.
At full load, 11.2 V at 40 mA (with 55 mA current limit) is available for the hazardous
area application.
This device mounts on a HiC termination board.
Functional Safety HiD2872, HiC2873(Y1), HiD2876, HiC2877
Product Description
2019-07
9
2.2 Interfaces
The device has the following interfaces.
• Safety relevant interfaces:
• HiC2873(Y1), HiC2877: input I, output I
• HiD2872, HiD2876: input I, input II, output I, output II
• Non-safety relevant interfaces: power supply, fault output
2.3 Marking
2.4 Standards and Directives for Functional Safety
Device-specific standards and directives
System-specific standards and directives
Note!
For corresponding connections see datasheet.
Pepperl+Fuchs GmbH
Lilienthalstraße 200, 68307 Mannheim, Germany
Internet: www.pepperl-fuchs.com
HiD2872
HiC2873
HiD2876
HiC2877
Up to SIL 2 (bus powered)
Up to SIL 3 (loop powered)
HiC2873Y1 Up to SIL 2 (bus powered)
Functional safety IEC/EN 61508, part 2, edition 2010:
Functional safety of electrical/electronic/programmable
electronic safety-related systems (manufacturer)
Functional safety IEC/EN 61511, part 1 –3, edition 2003:
Functional safety – Safety instrumented systems for the
process industry sector (user)
2019-07
10
Functional Safety HiD2872, HiC2873(Y1), HiD2876, HiC2877
Planning
3 Planning
3.1 System Structure
3.1.1 Low Demand Mode of Operation
If there are two control loops, one for the standard operation and another one for
the functional safety, then usually the demand rate for the safety loop is assumed to be
less than once per year.
The relevant safety parameters to be verified are:
• the PFDavg value (average Probability of dangerous Failure on Demand) and the T1
value (proof test interval that has a direct impact on the PFDavg value)
• the SFF value (Safe Failure Fraction)
• the HFT architecture (Hardware Fault Tolerance)
3.1.2 High Demand or Continuous Mode of Operation
If there is only one safety loop, which combines the standard operation and safety-related
operation, then usually the demand rate for this safety loop is assumed to be higher than
once per year.
The relevant safety parameters to be verified are:
• the PFH value (Probability of dangerous Failure per Hour)
• Fault reaction time of the safety system
• the SFF value (Safe Failure Fraction)
• the HFT architecture (Hardware Fault Tolerance)
3.1.3 Safe Failure Fraction
The safe failure fraction describes the ratio of all safe failures and dangerous detected failures
to the total failure rate.
SFF = (s + dd) / (s + dd + du)
A safe failure fraction as defined in IEC/EN 61508 is only relevant for elements or (sub)systems
in a complete safety loop. The device under consideration is always part of a safety loop
but is not regarded as a complete element or subsystem.
For calculating the SIL of a safety loop it is necessary to evaluate the safe failure fraction
of elements, subsystems and the complete system, but not of a single device.
Nevertheless the SFF of the device is given in this document for reference.
Questo manuale è adatto per i seguenti modelli
4
Indice
Altri manuali Pepperl+Fuchs Azionamento CC
Pepperl+Fuchs
Pepperl+Fuchs HiC2031 Manuale utente
Pepperl+Fuchs
Pepperl+Fuchs KFD2-SCD2-Ex LK Series Manuale utente
Pepperl+Fuchs
Pepperl+Fuchs HiD2038 Manuale utente
Pepperl+Fuchs
Pepperl+Fuchs KCD0-SD3-Ex1.1 45 Series Manuale utente
Pepperl+Fuchs
Pepperl+Fuchs HiC2871A Manuale utente
Pepperl+Fuchs
Pepperl+Fuchs KCD2-SLD-Ex1 Series Manuale utente
Pepperl+Fuchs
Pepperl+Fuchs SIL KCD2-SCD-Ex1-ES Manuale utente
Pepperl+Fuchs
Pepperl+Fuchs HiC2883 Manuale utente
Manuali Azionamento CC popolari di altre marche
Vincent Associates
Vincent Associates UNIBLITZ ED12DSS Manuale utente
EKSMA OPTICS
EKSMA OPTICS DQ-100-4 Manuale elenco delle parti
Chamberlain Garog
Chamberlain Garog D Series Manuale utente
Parker
Parker PDS Series Manuale utente
Festo
Festo DGC G Series Guida all'installazione
Binks
Binks QS-5012-1-CE Manuale utente
