Phason FC Seriess Manuale utente
FC-1T-1F 1 / 4 10940000
FC-1T-1F user manual
The FC-1T-1F automatically controls the temperature in a room by switching fans, lamps, or heaters on or off as
the temperature drops below or exceeds the temperature set point.
When the SSC-1D is in cooling mode, it switches on the fans when the temperature exceeds the set point. When
the control is in heating mode, it switches on the lamps or heaters when the temperature drops below the set point.
Features
One solid-state relay
Heat and cool modes
Adjustable temperature set point,
32 to 99°F (0 to 37°C)
Fahrenheit and Celsius display
Six-foot temperature probe (extendable)
Error code display for troubleshooting
Overload protection fuse
Rugged, NEMA 4X enclosure (corrosion
resistant, water resistant, and fire retardant)
CSA approval
Two-year limited warranty
Installation
Switch OFF the power at the source before connecting the incoming power wires.
DO NOT switch on the power until you have finished all wiring and verified all equipment is
properly connected and free of obstructions.
Electrical ratings
Input: 120/230 VAC, 50/60 Hz
Relay: 10 A at 120/230 VAC, general-purpose (resistive)
1/3 HP at 120 VAC, 1/2 HP at 230 VAC
360 W tungsten at 120 VAC
Fuse: 15 A, 250 VAC ABC-type ceramic
Temperature display units Mode of operation
FC-1T-1F 2 / 4 10940000
1. Set the voltage switch to the correct position for the line voltage used, 120 or 230 VAC.
2. Connect the wires as shown in the diagram.
Startup
When the control powers up:
1. 88 will display for 0.25 seconds (start-up).
2. 00 will display for 1 second (self-test).
3. 60 will display for 1 second. The 60 means that the frequency is 60 Hz.
4. The display will flash between the temperature and PF (power failure). Click the switch to the right to clear the
message.
FC-1T-1F 3 / 3 10940000
Display alerts
PS
The temperature sensor cable has short circuited.
PD
The temperature sensor is damaged or the connecting wire is broken.
tS
The Temperature knob has been turned. The display will alternately flash tS and the ambient temperature. The control will not
accept the new setting until the switch is clicked to the set position.
OR
The voltage switch is set to 230 but the incoming power is 120 volts. Make sure the voltage switch is in the correct position.
PF
There has been a power failure. The display will flash between the temperature and PF. Click the switch to the right to clear the
message.
Programming
Switch position
Function
CENTER
Displays the ambient temperature
RIGHT
Allows you to view and adjust the temperature set point
Clears alarms
LEFT
Allows you to verify if the control is in heating or cooling mode
Allows you to verify if the control is displaying Fahrenheit or Celsius
Temperature set point
The FC-1T-1F controls the temperature in a room by switching fans, lamps, or heaters on or off as the temperature
drops below or exceeds the temperature set point. The set point is the desired room temperature and can be set
between 32 and 98°F (0 and 38°C).
In cooling mode, the control switches on the load when the temperature exceeds the set point.
In heating mode, the control switches on the load when the temperature drops below the set point.
To adjust the setpoint
1. Click the switch to the right and hold.
2. Adjust the TEMPERATURE knob to the desired setting.
You must hold the switch in the set position while turning the TEMPERATURE knob. If this is not
done correctly, the display will flash between tS and the temperature display, indicating the
knob has accidentally been turned. The control will not accept the new setting until the switch is
clicked to the right.
PhasonControls.com [email protected] International: 204-233-1400 Toll-free North America: 800-590-9338
Questo manuale è adatto per i seguenti modelli
1
Altri manuali Phason Interruttore
