Philips Maestro DS9600 Manuale utente
S
ervice Manu
al
Published by AVS 0639 Service RCS Subject to modification 3104 205 5026-1
MAESTRO
TABLE OF CONTENTS Page
Specifications..................................................................................... 1
MechanicalInstructions SetDisassembly.................................... 2
Mechanical Instructions SetRe-assembly................................... 3
Explodedview& Mechanical Parts list............................................ 4
Explodedview - Dockingstation....................................................... 5
Electricaldiagrams-Docking station............................................. 6
Mechanical instructions & Set Disassembly.................................. 7
Mechanical & Electrical Parts list - Docking station..................... 8
TSU9600/00/05/37/79
DS9600
1-1
A.GENERALREQUIREMENTS
Operatingtemperature : between 5 °C and 45 °C
Storagetemperature : between-25 °Cand +70°C
Atmosphericpressure : 96 K Pa ± 6 K Pa
Relativehumidity : between 40 and 80 %
Transmittedcode : RC5, RC6,andlearnable format
Infraredwavelength: : 950nm ± 50nm.
ESD : with 8 kV applied to the outside, RC placed
ongrounded plane,no damage orfunctional
failures.
Items notmentioned :According UAW-422.
B.ELECTRICALREQUIREMENTS
Nominalbatteryvoltage : 3.7 V (Li-Ion battery pack)
Operatingvoltage : +4.2 ® 3.0 V (Li-Ionbattery pack)
:+5V (mainadaptor)
Leakagecurrent atnominal : £ 5 mA.
batteryvoltage(sleep mode)
Batterylifetime : 2 hrs continuous use.
Transmitted intensity on axis : ³ 70mW/Sr.
atnominal batteryvoltage
Totalopeningangle horizontal, : ± 22.5° Ie ³ 12mW/Sr.
verticalat nominalbatteryvoltage
Standby time : 1 day
C.PRODUCT DESCRIPTION
Maestro is a touchscreen LCD remote control with the following key characteristics:
- Colouractive matrixtouchscreen TFT LCDwith whiteLEDbacklight
(640x480, 16bit color)
- Backlight brightness control
- LCDrefresh rate60-80Hz
- Back lighted hard buttons
- Innovative,customizableuser interface
- Downloadableuniversaldatabase
- Smartpower management
- IRlearning distance:10…2.5cm @+-40degrees
- Learningfrequency 17kHz-1MHz.
- EmbeddedLi-Ion batterywithbuild-in recharger, 2100mAHcapacity
- 16-bitAudioDAconverter forCD-likesound quality
- USBdevice forconnection with PC
- IEEE802.11b/g WIFI moduleembedded
- Monoloudspeaker
- 64 MB Flash memory
- 64 Mbytes SDRAM
- 266MHzMX21Dragonball processor.
2-1
MECHANICALINSTRUCTIONS
3.Remove 5 x screw (Torxscrew M2x10).
SetDisassembly
3.Remove thebottompart coveritem 20by pullingit (bottomside)
on the place as shown in the picture.
3.overviewguideholes.
(for info only)
3.overviewguideline.
(for info only)
Note that battery is accessible now for replacement !
for replacement see: Set re-assembly on page 3-2
it is recommanded to order the battery (item 251) same
with a new approbation sticker (item 676) and new
rubber feets (item 07).
Battery replacement set: 1 X item 251
1 X item 676
2 X item 07
1.Remove carefullytheapprobation sticker
item 676 with the help of a label remover. 2.Remove onerubberfeet item07
on the right upper corner to make
the screw accessible.
locationofadhesive
Damperitem 06
2-2
MECHANICALINSTRUCTIONS
SetDisassembly
5a. Disconnect PB (item 1002) to release the flex-cable
(unlock connector 1003 with the help of a pincet). 5b. Take battery out, disconnect battery plug
(item 251) on connector 1701
4.Remove PB(item 1002)includesdocking
insert (item 22) by release the two
“plastic snap hooks” as shown in the picture.
5c.Remove 2Xscrews(Torxscrew M2X8)
on the position as shown in the picture.
6. - Release bottompart (item 02) from toppart (item 01).
step 1: very important is to start up with one of the “sides”
as shown in the picture.
- Put a sharp knife between toppart and bottompart and use
this as a lever to separate the two parts.
- Important: push up the bottompart compared with the toppart
to unlock the plastic snaps in the holes (bottompart).
2-3
MECHANICALINSTRUCTIONS
SetDisassembly
7. - Release bottompart (item 02) from toppart (item 01).
step 2: continue with the “top” as shown in the picture.
- Put a sharp knife between toppart and bottompart and use
this as a lever to separate the two parts.
- Important: push up the toppart compared with the bottompart.
to unlock the plastic snaps in the holes (bottompart).
8. - Release bottompart (item 02) from toppart (item 01).
step 3: continue with the “other side” as shown in the picture
- Put a sharp knife between toppart and bottompart and use
this as a lever to separate the two parts.
- Important: push up the bottompart compared with the toppart
to unlock the plastic snaps in the holes (bottompart).
9. - Release bottompart (item 02) from toppart (item 01).
step 4: finally continue with the “under side” as shown
in the picture.
- Put a sharp knife between toppart and bottompart and use
this as a lever to separate the two parts.
- Important: push up the toppart compared with the
bottompart. (as shown in the picture).
10a.Disconnect thespeaker plug(connector1601).
10b unlock connector 1402 with the help of a pincet and release
the flex-cable from the touchscreen (item 10).
2-4
MECHANICALINSTRUCTIONS
SetDisassembly
11.Torelease thePB (item1001),remove
5 X screws (Torx M2X6) as shown in
the picture.
item 08
keymat stdby
item 09
keymat cursor
item 13
lowerkey hinge
item 25
springpen
item 01
toppart sub assy
12.Removethe followingcomponentsfrom
the toppart sub assy (item 01).
13.Removethe followingcomponentsfrom
the toppart sub assy (item 01)
Be carefully:
item 01 + item 10
toppart sub assy + touchscreen
preserve this subsam assy for the rest
untouched!!.don’tremove anythingelse
as mentioned in this list.
item 28
Cursor holder
TSU9600
item 27
Cursorring assy
TSU9600
remove 2 Xscrew
M2X4
item 05
Backlight key
2-5
MECHANICALINSTRUCTIONS
SetDisassembly
09
01
13
25
08
200
28
27
Overview mechanicaltoppartcomponents.
02
1001
20
254
1002 22 33
Set Disassembly components.
254
13*
Overviewsnapholes inbottompart.
(for info only)
07
10
05
17 16
Set Disassembly and Re-assembly
2-6
MECHANICALINSTRUCTIONS
release the LCD bezel item 17 from PB 1001,
push downwards to unlock the 4 plastic snaps in
the snap holes as indicated in the picture.
Replacement off touchscreen
release the flex cable from LCD item 16 to unlock the
connector 1401 by till up the lid from connector 1401
(90 degrees), and take the LCD module out the LCD
bezel(item17).
item 17
LCDbezel item 16
LCDmodule
For LCD re-assembling use the opposite
sequence order and finally lock connector
1401 by pushing the lid from connector 1401
down again.
Replacement off LCD module item 16
item 01 + item10
servicesubsam touchscreen
Forservice people,the toppart(item 01)same withthe touchscreen(item 10)is alreadyprepared as
“subsampart” ancanbe orderedunderthe codenumber3104207 15620
Incase ofreplacement followthe instructionsSet Re-assemblyon page3-1
top
3-1
MECHANICALINSTRUCTIONS item 01
toppart sub assy
includestouchscreen
(item 10)
item 28
Cursor holder
TSU9600
add 2 X screw
M2X4
item 27
Cursorring assy
TSU9600
1. take toppart assy item 01
2. mount Cursor ring item 27
3.mount Cursorholder item28
4.Add2 Xscrew (TorxM2X4)on theposition
as shown in the picture
item 08
keymat stdby
item 09
keymat cursor
item 25
springpen 5. mount spring pen item 25
6. mount keymat cursor item 09
7. mount keymat stdby item 08
8. mount lower key hinge item 13
9. mount Backlight key item 05
(as shown in the picture)
item 13
lowerkey hinge
10. mount PB item 1001 in the bottompart
11. add 5X screws(Torx M2X6)onthe
position as shown in the picture.
Note that these 5 screw holes on the PB
are indicated with white circles
(service painting).
Set Re-assembly
item 05
Backlight key
3-2
MECHANICALINSTRUCTIONS
Set Re-assembly
mount the flex cable from touchscreen into
connector 1402 and lock the connector.
12. take the bottompart item 02.
13. plug in the speaker plug (item 254) to connector 1601.
14. plug in the flex cable touchscreen into connector 1402.
15. lock connector 1402.
16. place the bottompart to the toppart.
17. push the bottompart in such a way that the
plastic snaps from the toppart are fixed into
the snap holes from the bottompart.
18. add 2 X screw Torx M2X8 on the position as
indicated in the picture.
19. take PB item 1002.
20. take the flex cable item 8000 and put them
into connector 1003 from PB item 1002.
21. lock connector 1003.
22. take battery item 251.
23.plug battery plug into connector1701.
24. place battery in the battery holder position.
from the bottompart. Turn the battery until
it’s becomes in an mechanical free
position (clamp free !), so that the battery
can move (turn)a little bit.
connectthe speakerplug intoconnector 1601
item 8000
flex cable
screw screw
Battery
item 251
PB item 1002
Docking insert
item 22 On-Offswitch
item 33
Altri manuali Philips Stazione di attracco
Philips
Philips DC950/12 Manuale utente
Philips
Philips DC291/93 Manuale utente
Philips
Philips DC177 Manuale utente
Philips
Philips DC-291 Manuale utente
Philips
Philips DC-291 Manuale utente
Philips
Philips DC-291 Manuale utente
Philips
Philips DC1050/12 Manuale utente
Philips
Philips AJ300DB/05 Manuale utente
Philips
Philips Fidelio DCW8010 Manuale utente
Philips
Philips DCB291/05 Manuale utente
Philips
Philips LFH 9160 Manuale utente
Philips
Philips DCP851 Manuale utente
Philips
Philips DCB146 Manuale utente
Philips
Philips DC315/37 Manuale utente
Philips
Philips DC315/93 Manuale utente
Philips
Philips DC290 Manuale utente
Philips
Philips DC390/98 Manuale utente
Philips
Philips AZ1330D/05 Manuale utente
Philips
Philips DC315/12 Manuale utente
Philips
Philips DCM580/12 Manuale utente
