Philips BVP483 Manuale utente

Installation Instruction

Industrial Luminaire

LED FLOOD LIGHT

Application : Outdoor only

Type : BVP483

Max. Projected Area : 0.14 m²

Voltage : 240 V, 50 Hz

IP Classification : IP 66

Lamp : LED

Net Weight : 7.0 kg Approx

CCT : 5700 K

IP-66

Industrial Luminaire

LED FLOOD LIGHT

Dimensions in mm

Caution: Mounting to be done using M12 Bolts(3x)

Warranty void if earthing is not connected.

Installation Instruction

372

536

588 62

28 28

Ø16.2

186

100

200

CAUTION

1. Ensure L-N-E is connected in right manner.

2. Ensure 3 core cable for Connections(Outer diameter 8-10 mm, multi strand 1.5 sq. mm thickness)

with IP-65 protected cable joint (Follow steps 2,3,4 & 5 for 3 Core cable assy, only if required).

3. 3 Core cable should be properly connected with ground.

4. Ensure mounting bracket is properly mounted with three M12 bolt at 30 N-m torque.

5. Product should be operated between 120-270V A.C.

6. Luminaire must be brought down from the mounting position for maintenance.

7. In case the Lensplate is found broken/damaged it should not be powered on and is to be replace

before using the luminaire.

8. The light source of this luminaire is not replaceable, when the light source reaches

its end of life the whole luminaire shall be replaced.

FAILURE OF PRODUCT DUE TO NON COMPLIANCE TO ANY OF THE ABOVE, VOIDS WARRANTY

OF PRODUCT.

All the pictures in the MI sheet are representative only and may vary from the Actual Product.

40 mm 8-9 mm

O 8-10 mm

Make the electrical connections in 3 pole connector

as per the ENL marking. Use 1.5 sq mm cable.

M10 (2x)

17 N.m

Take the Luminaire out of the packing Box.

Remove the cable tie and mount the Bolt Caps.

(Cable tie is used on both sides of handles to

secure the bolt cap).

Unscrew the M5x20 Captive screw to open the gear

cover and to have access to the electrical connections.

Caution: Gland should never be above centerline

Note: Gear cover has Self retaining screws.

Unpack the Bolt caps, loosen

the M10 Bolts. Adjust the angle, tighten the bolts.

Put the bolt caps back.

Center

Line

40 mm 8-9 mm

O 8-10 mm

For External wire connection use watertight

Ip65 Box (not part of Luminaire)

1. 2. 7.

10.

Center

Line

Caution: Warranty void if earthing is not connected.

Secure the Gasket on the housing ribs. Ensure ribbed

side of gasket is on the outer side. (As shown in Fig 4)

Place the Gear Cover on the housing matching the

profile of gasket.

Ribbed side

of gasket X-Section

Fig. 1 Fig. 2

Fig.3 Fig.4

Fig. 5 Fig. 6

Fig. 7

Fig. 10

Housing ribs

M12 (3x)

30 N.m

Outer side

Mount the Luminaire

on the Bracket using 03

nos. of M12 screws applying

a torque of 30 Nm.

LONGER SIDE

SHORTER SIDE

Fig. 8

Suitable for mounting

from Bottom

Fig. 9

DETAIL B

Press the Cover applying uniform pressure over the

top surface. Ensure that gasket is not deformed and

stays inside the cover.

Engage the M5 screws with the housing applying torque

of 1 Nm initially in the sequence as shown in fig. 2.

Finally tighten the Screws with a torque of 2 Nm in the

same sequence

Remove

the bolts

Remove

the bolts 1

Rotate the bracket

Mount it on luminaire.Tighten

M10 Bolts with a torque of 17Nm.

Put the Bolt Caps back.

Suitable for mounting

from Top

Fig 9A

Fig 9B

Fig 9C

Fig 9D

All the pictures in the MI sheet are representative only and may vary from the Actual Product.

Gasket

Ribbed

Side

After Gasket Assy

Altri manuali Philips Proiettore

Philips

Philips VL500 Wash Luminaires Manuale utente

Philips

Philips 31607-48-16 Istruzioni per l'installazione

Philips

Philips Clearflood Large BVP651 Manuale utente

Philips

Philips GearUnits ECM 330 Manuale utente

Philips

Philips MVF 406, 1800 W cat A1 Guida rapida

Philips

Philips eXpanium eXp 401 Manuale utente

Philips

Philips BVP158 Manuale utente

Philips

Philips Selecon Manuale utente

Philips

Philips conTempo RVP150 Manuale utente

Philips

Philips BVP510 Guida utente

Philips

Philips BVP500 Guida utente

Philips

Philips SL ParBlazer 100 UV Manuale di istruzioni

Philips

Philips SL WASH 180 RGBW Manuale di istruzioni

Philips

Philips BVP080 Guida utente

Philips

Philips BVP150 Manuale utente

Philips

Philips P-2558-C Manuale utente

Philips

Philips BVP154 Series Manuale utente

Philips

Philips SmartBright BVP171 Manuale utente

Philips

Philips BVP131 Guida utente

Philips

Philips BVP158 LED24/WW NW CW PSU 20W SWB CN Manuale utente

Philips

Philips Showline SL PAR 150 ZOOM Manuale utente

Philips

Philips F Series Manuale utente

Philips

Philips SmartBright BVP173 Manuale utente

Philips

Philips 40745-17-16 Manuale utente

Manuali Proiettore popolari di altre marche

VIZULO

VIZULO Micro Martin Guida utente

EuroLite

EuroLite LED IP FL-100 SMD Manuale utente

Cooper Wheelock

Cooper Wheelock XB12 Manuale utente

Allen + Roth

Allen + Roth 17624-000 Manuale utente

ADJ

ADJ 4 STAGE PAK Manuale utente

Cooper Lighting

Cooper Lighting EGL91SW233 Manuale utente

Max

Max 37496 Manuale utente

BEGA

BEGA 85 143 Manuale utente

Beamz

Beamz 151.226 Manuale utente

EuroLite

EuroLite LED IP FL-8 Manuale utente

Ledj

Ledj PERFORMER 36 RGB Manuale utente

Perel

Perel ELS3 Manuale utente

Perel

Perel ELS3WD Manuale utente

LumX

LumX LM 36130 Manuale utente

Xtricity

Xtricity 4-80053 Manuale utente

Stahl

Stahl 6521/4 Series Manuale utente

Ecosense

Ecosense EcoSpec Manuale utente

Ayrton

Ayrton minipanel FX Manuale utente