Philips IntelliVue MP40 Manuale utente

Patient Monitoring

Hardware Upgrade Installation Guide

IntelliVue MP40/50

IntelliVue Patient Monitor

MP40/50

M8003-9301A

*M8003-9301A*

Part Number M8003-9301A

1Introduction 3

2Checking your Tools and Kit Hardware 5

3Installing J13 - J30 7

4Installing J40 11

5Installing E12 13

6Installing E25 21

7Verification of Upgrade 25

1Introduction

This document contains or refers to proprietary information which is protected by copyright. All rights

are reserved. Copying or other reproduction of this document is prohibited without the prior written

permission of Philips Medical Systems.

WARNING The electrical characteristics of anti-static mats should be checked before use, as described in the

manufactuerer’s instructions for continued protection to both you and the equipment.

CAUTION A recommended anti-static table mat is the Minnesota Mining and Manufacturing Company (3M)

Part Number 8210. In addition to the table mat the person disassembling the monitor should either:

1Wear a conductive wrist strap (#M Part No. 2046) attached to the mat by the 1.2 m (4”) wire

included with it, or

2Stand on a floor mat with leather-soled shoes.

Before handling any circuit boards, firmly touch the exposed metal on the case to equalize the ground

potentials. This will prevent static discharge and protect the logic components of the monitor.

Handle circuit boards on the edges only; avoid touching board surfaces unless performing circuit board

repair. Contaminants like skin oil will attract dust to accumulate which could retain moisture and

affect the circuit performance.

1Introduction What is in this Installation Note?

What is in this Installation Note?

This installation note contains procedures on how to install the following upgrade kits for the

IntelliVue MP40/50 patient monitors:

M8027A

#J13 Serial Interface / MIB ready (2 ports)

#J14 Parallel Printer Interface

#J22 PS/2 Interface (2 ports)

#J23 Interface for the Remote SpeedPoint and Alarm Device

#J30 Flexible Nurse Call Relay

#J40 Advanced Interface: Wireless Network, SVGA Video, Nurse Call Relay

#E12 Add four internal module slots

#E25 Add Battery operation

2Checking your Tools and Kit

Hardware

Tools Required

You will need the following tools to complete the upgrade:

• Torx screwdrivers (sizes 6,10,20)

• 5/16" (5mm) Allen Wrench

• 2 Small flat head screwdrivers

• Needle Nose Pliars

• ESD mat and wrist strap

• 1 small Pozi or Philips head screwdriver

Hardware List

Before beginning, check that your upgrade kit has the hardware listed next to the appropriate option in

the table below:

Kit Part Number Description

J13 M8081-67501 Serial Interface (MIB ready) board

J14 M8082-67501 Parallel Printer Interface board

J22 M8086-67501 PS/2 Interface board

J23 M8086-67521 Interface board for Remote SpeedPoint and Alarm Device

J30 M8087-67501 Flexible Nurse Call Relay board

J40 M8090-69501 System Interface Board Advanced

E12 M8003-69504 Four Slot Rack Assembly

E25 M8067-69501 Battery Board

2 Checking your Tools and Kit Hardware Hardware List

3Installing J13 - J30

This section decribes how to install the following upgrade options:

– J13 - Serial Interface / MIB ready

– J14 - Parallel Printer Interface

– J23 - Remote Speedpoint and Remote Alarm Device

– J22 - PS/2 Interface

– J30 -- Flexible Nurse Call Relay

Installation Instructions

Removing the Blank Covers

CAUTION Make sure to unplug the AC power cord and to remove the batteries before removing blank covers or

I/O boards. Failure to remove the power cord and the batteries could cause damage to the CMU as it is

still under power.

1Remove the two screws securing each of the blank covers and remove them.

3 Installing J13 - J30 Installation Instructions

2Use the board removal tool located inside the battery compartment door to pull off the blank

covers (or other I/O boards, if boards need to be switched).

Installing the I/O Boards

Insert the I/O board into the slot according to the following table:

Board Removal Tool

Slot 1

Slot2

Slot 3

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali Philips Monitor

Philips

Philips BDH5021V Manuale utente

Philips

Philips 109B4074 Istruzioni per l'installazione e il funzionamento

Philips

Philips 17B2402H Manuale utente

Philips

Philips 109E5 Manuale utente

Philips

Philips AE5430 Manuale utente

Philips

Philips Signage Solutions BDL4254ET Manuale utente

Philips

Philips 220X1SW/05 Manuale utente

Philips

Philips 170B2B Istruzioni per l'installazione e il funzionamento

Philips

Philips 170N4 Manuale utente

Philips

Philips 170V6FB Manuale utente

Philips

Philips 8528 Series Manuale utente

Philips

Philips 160E1SB/93 Manuale utente

Philips

Philips 170S6FG Manuale utente

Philips

Philips Brilliance 241B7QUPBEB/75 Manuale utente

Philips

Philips 202EL2SB Manuale utente

Philips

Philips 220VW9FB Manuale utente

Philips

Philips 105S Manuale utente

Philips

Philips 190V8FB Manuale utente

Philips

Philips 150S4FB Manuale utente

Philips

Philips 190X6 Manuale utente

Philips

Philips 86BDL6051C Manuale utente

Philips

Philips 10BDL3051T/00 Manuale utente

Philips

Philips 288B6 Manuale utente

Philips

Philips 105G7 Manuale utente

Manuali Monitor popolari di altre marche

Linear Acoustic

Linear Acoustic LQ-1000 Manuale utente

AOC

AOC I2579V Manuale utente

Gateway

Gateway FPD1520 Manuale utente

Furuno

Furuno Mu 120c Manuale utente

Asus

Asus VB171D - 17" LCD Monitor Manuale utente

Dell

Dell S2230MX Istruzioni utente

Dell

Dell S2409WFP Manuale utente

EverFocus

EverFocus EN-7517E Manuale utente

Panasonic

Panasonic TH152UX1 - 152" PLASMA TV Manuale utente

Dell

Dell Precision 7680 Manuale di istruzioni

LG 50PM1M - - 50" Plasma Panel Manuale utente

Bosch

Bosch DDU 9 Manuale utente

Acer

Acer A231HL Manuale utente

NEC

NEC AccuSync LCD5V Manuale utente

Emay

Emay SleepO2 Manuale utente

IBM

IBM 6360 Istruzioni per l'installazione

LG M1950D-PZ Manuale utente

Sceptre

Sceptre D40 Manuale utente