Philips SLV3220 Manuale utente
Wireless TV Link
User Manual
SLV3220
F202019
SLV3220 WIRELESS TVLINK TRANSMITTER
21
SLV3220 WIRELESS TVLINK RECEIVER
WIRELESS
WIRELESS
WIRELESS
WIRELESS
SOURCE
IR
DC 9V
VIDEOAUDIO L
R
PICTURE
1 2 3 4
CHANNEL
SOURCE 1 SOURCE 2
DC 9V
CHANNEL
PICTURE
1 2 3 4
SOURCE
A
B1312 14
21 4 53
678910
151617
3
EN
Contents
Page
Overview 4
Control and display elements 4
Your Wireless TV Link 5
Safety 5
Installation 6
Operation 7
Enjoy your Wireless TV Link 7
Troubleshooting 9
Information 11
Information 11
Maintenance and service 11
Recycling and disposal 11
Warranty 12
Glossary 12
4
EN Overview
Control and display elements
A Transmitter
1 Integrated remote control blaster light
2 On/off switch
3 Power light:
> red: standby
> green: on
4 TV2 source indicator
5 SOURCE button
6 Power input connector (DC 9V)
7 Wireless channel selection switch
8 SOURCE 2 connectors (red/white/yellow)
9 SCART cable
10 Remote control blaster cord port
B Receiver
12 Integrated remote control blaster light
13 On/off switch
14 Power light:
> red: standby
> green: on
15 Power input connector (DC 9V)
16 Wireless channel selection switch
17 SCART cable
F Remote control blaster cord
19 Connector
20 Blaster light
5
EN
Your Wireless TV Link
You can say good-bye to wires. With your Wireless TV
Link you can now wirelessly connect a second TV and
choose between two devices to watch on your second
TV.
Safety
• Read the instructions in this manual carefully before
you connect, install and use the product.
• Keep this manual for future reference.
• The product is for indoor use only.
• Do not use the product close to water.
• Do not expose the product to extreme heat.
• In case of technical difficulties, do not open the
product. Bring it to your Philips dealer.
• Do not cover the product.
• Connect the power adapters only to a
220-240 V AC/50 Hz power supply.
• The product can cause interference to other
equipment. Check if any equipment near the product
can be affected before you start using it.
6
EN Installation
Install the remote control blaster cord
1 Switch off the transmitter (A).
2 Connect the remote control blaster cord (F) to the
IR socket.
3 Position the blaster light in front of the IR sensor of
the video source.
4 Switch on the transmitter (A).
5 Take the remote control of a video source with you.
6 Go to TV2.
7 Switch on TV2.
8 Switch on the receiver (B).
9 Select the correct SCART input on TV2.
10 Operate the video source with its remote control.
11 If necessary, repeat the steps 3 to 10 for the other
video source.
For basic installation, see
the quick start guide that
came with your Wireless
TV Link.
See the user manual of the video source
for the exact location of the IR sensor
on the front panel.
7
EN
Installation
Remove interference on TV2
1 Find the PICTURE CHANNEL switch on the
transmitter (A).
2 Set the PICTURE CHANNEL switch to a
different number.
3 Find the PICTURE CHANNEL switch on the
receiver (B).
4 Set the PICTURE CHANNEL switch to the same
number as on the transmitter (A).
Operation
Enjoy your Wireless TV Link
Watch a cable TV program on TV2
1 Switch on the transmitter (A).
2 Switch on the VCR or DVD recorder.
For basic operation, see
the quick start guide that
came with your Wireless
TV Link.
Your VCR or DVD recorder needs to
be connected to the transmitter (A) of
the Wireless TV Link and connected to
the Cable-TV signal.
8
EN Operation
3 Press SOURCE on the transmitter to select the
VCR or DVD recorder.
4 Take the remote control of the VCR or DVD
recorder with you.
5 Go to TV2.
6 Switch on TV2.
7 Switch on the receiver
8 Select the channel on the VCR or DVD recorder
with its remote control.
Watch a video source on TV1
Operate TV1 and the video source as usual.
SOURCE21
Turn off the auto standby mode when
you use the VCR or DVD recorder to
watch a cable tv program. Refer to the
user manual of the VCR or DVD
recorder.
If the VCR or DVD recorder records a
television program, you watch the
recorded channel.
9
EN
Troubleshooting
Problem Tip
No image or
wrong image on
TV1
• Make sure video sources are con-
nected to the transmitter (A).
• Make sure the transmitter (A) is
connected to TV1.
• Make sure SCART cables are
firmly inserted.
• Make sure the video source is
switched on.
• Make sure the correct SCART
input on TV1 is selected.
No image or
wrong image on
TV2
• Make sure SCART cables are
firmly inserted.
• Make sure the receiver (B) is con-
nected to TV2.
• Make sure both receiver (B) and
transmitter (A) are switched on.
• Make sure the video source is
switched on.
• Make sure the correct SCART
input on TV2 is selected.
• Select the correct video source
with SOURCE on the transmit-
ter (A). See page 7.
• If the video source gives proper
image on TV1:
Make sure the video source gives
video signal in CVBS mode. See
its user manual
• Change the wireless channel that
is used for communication. See
page 7.
• The receiver (B) is out of range of
the transmitter (A). The number
of walls and ceilings in between
the receiver (B) and transmitter
(A) restrict the distance.
10
EN Troubleshooting
Problem Tip
Interference on
the image of TV2. • Slightly change the position of the
receiver or the transmitter.
• Change the wireless channel that
is used for communication. See
page 7.
• The receiver (B) is out of range of
the transmitter (A). The number
of walls and ceilings in between
the receiver (B) and transmitter
(A) restrict the distance.
The video sources
do not respond to
the remote con-
trol commands
from TV2.
• Point the remote control directly
to the receiver.
• Replace the batteries of the
remote controls with new ones.
• Install the remote control blaster
cord (F). See page 6.
• The maximum operating distance
of the remote control is 5 m.
The television
program disap-
pears on TV2.
• Turn off the auto standby mode
of the video source. See its user
manual.
• Follow the instructions to recon-
nect the video sources. See the
quick start guide.
Buzzing sound
when you use the
remote control.
• Slightly change the position of the
receiver or the transmitter until
the buzzing sound stops.
• Sometimes it is not possible to
solve the problem.
Easylink feature
does not work. • Check if the TV and VCR support
Easylink.
• Check if you used full-wired
SCART cables.
Black and white
image with S-VHS
VCR.
• Check if the SCART connector of
the S-VHS VCR gives signal in
CVBS. See its user manual.
Questo manuale è adatto per i seguenti modelli
2
Indice
Altri manuali Philips Ricevitore
Philips
Philips MatchLine FR980 Manuale utente
Philips
Philips DTR4610 Istruzioni operative
Philips
Philips DCR 5012 Manuale utente
Philips
Philips DTP2130 Manuale utente
Philips
Philips HTS3500K/51 Manuale utente
Philips
Philips DTR2000/00 Manuale utente
Philips
Philips HTS3400 Manuale utente
Philips
Philips AE 3750 Istruzioni per il montaggio
Philips
Philips FR751 Manuale utente
Philips
Philips FR740/00 Manuale utente
Philips
Philips HTS3105MKI98 Manuale utente
Philips
Philips MX2600/55 Manuale utente
Philips
Philips DTR 210 Manuale utente
Philips
Philips HTR5000 Manuale utente
Philips
Philips Matchline FR970 Manuale utente
Philips
Philips Fidelio A1 Manuale utente
Philips
Philips HTR5000 Manuale utente
Philips
Philips PREMIERE DCR 2021 Manuale utente
Philips
Philips DFR9000 Manuale utente
Philips
Philips Streamium SL50i Manuale utente
