Philips AUT2015 Manuale utente

Under-the-sink ltration

AUT2015

Water Solutions

User manual 1EN Manual del usuario 17ES

Manuel d'utilisation 34FR Manuale utente 52IT

Руководство пользователя 69RU

Content

I. Product Introduction 1

II. Product Specifications 1

III. Product overview and

installation illustration

IV. Installation

Install the three-way ball valve

Install the faucet

Install the system

V. Usage instruction

Before the first-time use

User interface

VI. Maintenance

Routine maintenance

Filter lifetime

Filter cartridge replacement

VII. Precautions

Warning

VIII. Troubleshooting 13

IX. Guarantee & Service 15

X. Packing list 15

Installation

I. Product Introduction

Congratulations on your purchase and welcome to Philips! Our reverse osmosis

under-the-sink water ltration systems are with high ltration ow rate and tankless

design, which ensure every drop of water is freshly filtered and save space. The

reverse osmosis membrane has a deep ltration level down to 0.0001 micron, which

effectively removes viruses, bacteria, heavy metals, pesticides, water hardness,

volatile organic compounds, chlorine, and more, giving you great tasting water.*

Read this user manual carefully before you use the appliance. Save it for future reference.

Note:

The water supplied by reverse osmosis systems has low mineral content. The mineral salts

required by the human body are provided by food and to a lesser extent by the water we drink.

* The substances removed or reduced by this system are not necessarily in all user’s water.

II. Product Specification

Product name Philips reverse osmosis under-the-sink water

filtration system

AUT2015

2 liters/minute

CP filter: 6,000 liters

RO filter: 11,000 liters

Product model

Filtered water flow rate

Filtration capacity

Inlet water pressure 0.1-0.4 MPa**

Inlet water temperature 5℃-38℃

1.05 liters/minuteRO filtered water flow rate

Rated voltage

Rated power 65W

Maximum inlet water TDS 1500 ppm***

24V

III. Product overview and installation illustration

Maximum inlet water

hardness 25 °HF***

Applicable water source

Municipal tap water, which meets all European

Directive on Water for Human Consumption 98/83

requirements and its national transpositions in

the various EU member states.

** When the inlet water pressure exceeds 0.4 MPa, a pressure relief valve should

be installed before the system. When the inlet water pressure is below 0.1 MPa,

a pressure booster should be installed before the system. The pressure relief valve

and extra pressure booster need to be purchased separately.

*** If the salinity of inlet water exceeds 1500 ppm, or the hardness exceeds 25 °HF,

the lifetime of the lters may be impacted. Please consult with your dealer about

installing prefilters before the system.

Sediment and carbon block filter 2-in-1 (CP)

1Cover

Reverse osmosis lter (RO)

System

Faucet and accessory

Quick connect fitting

7Three-way ball valve

1/4” PE pipe

3/8” PE pipe

Leakage detector

Power adapter with plug

Drain connector

51110

IV. Installation

Note:

- Before installation, it is important to check the condition of the system to

make sure it has not been damaged during transport.

- Unpack the system and its accessories. Remove the protective packaging material.

Recyclable materials have been used for the packaging and should be disposed

of in the appropriate recycling bins or at the specific local recycling center.

Warning: Keep plastic bags out of the reach of children, as they may be dangerous.

- Check if anything is missing according to the packing list and the overview.

- Given that the system will improve the quality of your drinking water, all tools

to be used in the installation process should be clean, rust and grease-free.

- The installation process should be carried out under appropriate hygienic

conditions, taking all necessary precautions concerning materials and components

that will come into contact with water to be treated or consumed.

- Avoid external contamination of the system through improper handling, using

gloves, sanitizing gel, and washing hands as often as is necessary during the

installation process, first use, and system maintenance.

- The system and installation shall comply with applicable local regulations.

Hot

Cold

Three-way ball valve

Drain outlet pipe

Water inlet pipe

Filtered water outlet pipe

RO filtered water outlet pipe

Faucet

Power adapter

Leakage detector

Drain connector

b. Slide the nut of the three-way ball valve onto the 3/8" PE pipe pipe and insert

the pipe into the opening of the three-way ball valve. Tighten the nut with a wrench.

c. Install the three-way ball valve on the cold

water valve. Please don’t miss the gasket

inside the three-way ball valve during

installation.

- This product cannot be disposed of with other domestic waste products.

At the end of the product’s service life, it should be returned to the place of

purchase, or at a local recycling center, indicating that it contains electric

and electronic components. The appropriate collection and treatment

of the product, which no longer are to be used, contributes to the

preservation of natural resources and avoids any potential public health risks.

1. Install the three-way ball valve

a. Turn off the cold water supply. Turn on the kitchen cold water faucet to release

the pressure and allow water to drain from the line. Disconnect the cold water

hose from the cold water valve.

Gasket

(1)

(2)

Cold

(1) (2)

Hot Cold

e. Switch off the three-way ball valve. Turn on

the cold water supply. Wipe the connections

with a tissue to see if there is leakage. If the

tissue stays dry, it means the three-way ball

valve is installed properly.

2. Install the faucet

Note:

Select an appropriate installation position. The environment where the faucet is

installed should adhere to any appropriate hygiene and sanitation conditions.

Make sure the faucet sits flat on top of the sink or countertop surface.

a. Drill a hole with a diameter of

about 29mm. Skip this step if

there is already a hole in the sink

or the countertop surface.

b. Install the faucet according to the

diagram. Screw the faucet stem

nuts all the way up the faucet stem,

and tighten them to secure the

faucet with a 14mm socket spanner.

Hot Cold

(1)

(2)

d. Connect the cold water hose with the

three-way ball valve and screw it tightly with

a wrench. Please don’t miss the gasket in the

cold water hose during installation. (1) (2)

Gasket

Filtered

water

RO ltered

water

Base

Rubber washer

Washer

Nuts

b. Connect the water inlet and the three-way ball valve.

Measure the length of the 3/8" pipe you need to connect the system and the

three-way ball valve, and cut it accordingly with a pipe cutter. Insert the other

end of the 3/8" pipe which has been connected with the three-way ball valve

into the water inlet hole in the back of the system. Use a clip to secure the pipe

at the hole.

Note: The inlet water pressure should be within 0.1-0.4 MPa. If the pressure is too

low, a pressure booster should be installed prior to the system. If the pressure

is too high, a pressure relief valve should be installed prior to the system.

3. Installing the system

Note:

Please check if there is sucient space for installing the system itself, its accessories,

connections, and for servicing and repair. Under no circumstances should the system

be installed outdoors. The environment where the system is installed should

adhere to any appropriate hygiene and sanitation conditions. Avoid any external

dripping liquids from pipes or drains etc onto the system.

This system should be placed on a stable and at surface. Keep the system away

from heat. It shall not be placed in a place that may have inammable gas leakage.

a. Press down the collets and pull out the plugs

of the water inlet and outlet holes in the back

of the system.

c. Connect the water outlets and the faucet.

After you measure the length of the 1/4" pipe you need to connect the system

and the faucet, cut the 1/4” pipe with a pipe cutter. Insert one end of the pipe into

a quick connect tting, and connect the quick connect tting on the longer stem

of the faucet. Insert the other end of the 1/4" pipe into the RO ltered water outlet

hole in the back of the system until it stops. Use a clip to secure the pipe at the hole.

Cut another 1/4” pipe with the pipe cutter. Insert

one end of the pipe into a quick connect tting,

and connect the quick connect tting on the

shorter stem of the faucet. Insert the other end

of the 1/4" pipe into the ltered water outlet

hole in the back of the system until it stops.

Use a clip to secure the pipe at the hole.

d. Connect the drain water outlet and the drain connector

Identify the drain outlet location. Drill a 6.5mm hole on the drain pipe. Install the

drain connector according to the diagram. Securely tighten the nuts. Cut a section

of 1/4” pipe. Insert one end of the pipe into the drain outlet hole in the back of

the system until it stops. Use a clip to secure the pipe at the hole. Insert the other

end of the pipe into the drain connector.

Quick connect

ttings

Filtered water

outlet pipe RO ltered water

outlet pipe

Filtered water RO ltered water

Clip

(1)

(2)

(3)

e. Connect the leakage detector and the power adapter with the system.

DO NOT put the plug in the socket yet.

f. Move the system to its space in the under-the-sink cabinet and place the leakage

detector next to the system on the oor, which should be dry.

g. Remove the plastic wrap of the lter cartridges. Insert the lter cartridges in the

system accordingly, and turn them clockwise to align the triangle icon on the lter

cartridge with the lock icon on the system.

Note:

- Do not install the drain connector onto the same drain pipe as the garbage disposal.

- Do not penetrate opposite side of the pipe when drilling the hole.

(1)

(2)

4Water inlet

Clip

Drain outlet

RO Filtered

water outlet

Filtered water

outlet

Indice

Lingue:

Altri manuali Philips Sistema di filtraggio dell'acqua

Philips

Philips Pure Taste WP3861 Manuale utente

Philips

Philips AUT7006 Manuale utente

Philips

Philips AC4144 Manuale utente

Philips

Philips AWP3753 Manuale utente

Philips

Philips AUT3268 Manuale utente

Philips

Philips AWP9820/10 Manuale utente

Philips

Philips WP3892/01 Manuale utente

Philips

Philips Micro Pure WP3811 Manuale utente

Philips

Philips AWP2900 Manuale utente

Philips

Philips Pure Taste WP3861 Manuale utente

Philips

Philips AWP9820 Manuale utente

Philips

Philips WP3820 Manuale utente

Philips

Philips WP3812 Micro X-Pure Manuale utente

Philips

Philips AUT2016 Manuale utente

Philips

Philips AC4143 Manuale utente

Philips

Philips AC4012 Manuale utente

Philips

Philips Micro Pure WP3811 Manuale utente

Philips

Philips Saeco AquaClean CA6903/47 Manuale utente

Philips

Philips Saeco AquaClean CA6903 Manuale utente

Philips

Philips AC4142 Manuale utente

Philips

Philips HR6949/01 Manuale utente

Philips

Philips AC4143 Manuale utente

Philips

Philips WP3892 Manuale utente

Philips

Philips AWP1775WH Manuale utente

Manuali Sistema di filtraggio dell'acqua popolari di altre marche

Wisy

Wisy LineAir 100 Manuale utente

Schaffner

Schaffner Ecosine FN3446 Series Manuale operativo

Pentair

Pentair FLECK 4600 SXT Guida utente

H2O International

H2O International H20-500 Manuale utente

Renkforce

Renkforce 2306241 Manuale utente

Neo-Pure

Neo-Pure TL3-A502 Manuale utente

FLTR

FLTR OBF Manuale utente

STA-RITE

STA-RITE VERTICAL GRID DE FILTERS S7D75 Manuale utente

Applied Membranes

Applied Membranes W-G844EM Manuale utente

BEGA

BEGA 116 Manuale utente

WATA

WATA Standard Manuale utente

Price

Price FFU series Manuale

Gaggenau

Gaggenau BRITA INTENZA 467873 Manuale utente

Brita

Brita SAFF-100 Manuale utente

HEISSNER

HEISSNER FPU24000-00 Manuale utente

BGS technic

BGS technic 1518 Manuale utente

Reverse Osmosis

Reverse Osmosis RF Series Manuale utente

ubbink

ubbink Filtramax Series Manuale utente