Planet EH-2400 Manuale utente

EH-2400

Ethernet Hub User’s Manual

DISCLAIMER

We make no representation or warranty with respect to the contents or use of this manual, and

specifically disclaim any expressly implied warranties of merchantability or fitness for any particular

purpose. Further, we reserve the right to revise this publication and to make changes to its content, at

any time, without obligation to notify any person or entity of such revisions or changes.

FCC WARNING

This equipment generates, uses, and can radiate radio frequency energy and if not installed and used

in accordance with the instructions, may cause interference to radio communications. This equipment

has been tested and found to comply with the limits for a Class B computing device pursuant to

Subpart J of Part 15 of FCC Rules, which are designed to provide reasonable protection against such

interference when operated in a commercial environment.

Changes or modifications not expressly approved by the party responsible for compliance could void

the user's authority to operate the equipment.

TRADEMARKS

All the trademarks and trade names mentioned in this manual are the property of their respective

companies.

Revision

The information in this manual is subject to change without notice.

User's manual for PLANET Ethernet Hub :

EH-2400

Rev 2.0 (Nov. 1999)

Part No. EM-2400V2

TABLE OF CONTENTS

CHAPTER 1 INTORDUCTION....................................................................................................................1

PRODUCT INTRODUCTION....................................................................................................................................1

PRODUCT FEATURES ...........................................................................................................................................1

UNPACKING THE HUB..........................................................................................................................................1

CHAPTER 2 GENERAL DESCRIPTION ...................................................................................................2

FRONT PANEL OF EH-2400..................................................................................................................................2

LED INDICATOR..................................................................................................................................................2

REAR PANEL OF EH-2400 ...................................................................................................................................3

CHAPTER 3 INSTALLATION.....................................................................................................................4

GETTING READY TO INSTALL THE EH-2400 ........................................................................................................4

PREPARE TO INSTALL EH-2400......................................................................................................................4

EH-2400 INSTALLATION .....................................................................................................................................5

CONNECTING THE HUB TO AC POWER ................................................................................................................5

POWER FAILURE..................................................................................................................................................5

CHAPTER 4 TROUBLESHOOTING...........................................................................................................6

CHAPTER 5 PRODUCT SPECIFICATION ...............................................................................................7

CHAPTER 1

INTORDUCTION

Product Introduction

EH-2400 is a standard Ethernet concentrator that retimes and re-transmits the signal to each

network station on the LAN. It simplifies the implementation of twisted-pair Ethernet

compatible networks following the IEEE 802.3 10Base-2/5/T CSMA/CD standard. Each Hub

has twenty-four modular RJ-45 STP ports and one BNC port . one AUI port for attaching

network devices (file server, bridge, and workstations) or additional concentrators.

Product Features

EH-2400 provides all the functions necessary to support the requirements of Ethernet

networks. These function includes the following features:

q24-port STP RJ-45 connector and one port BNC, one port AUI.

qManchester decoder for clock and data recovery

qAutomatic preamble regeneration to compensate for any bit loss

qLockup and auto-partition for jabber to isolate network failures

qBuilt-in Micro processor detects the utilization of the hub

q19-inch Rack-Mount for industrial standard

qAuto-Polarity correction

qAutomatic address generation to disable transmission to the active port

qLEDs for Power, Link, TX/RX, partition, Collision, and Utilization

Unpacking the Hub

Carefully unpack the package and check its contents against the checklist given below.

Checklist of EH-2400 10Base-2/5/T Hub

•24-port 10BASE-2/5/T Ethernet Hub

•Power Cord

•User's Manual

Please inform your dealer immediately for any wrong, missing, or damaged part if possible,

retain the carton including the original packing materials, and use them against to repack

the product in case there is a need to return it to us for repair.

CHAPTER 2

GENERAL DESCRIPTION

Front Panel of EH-2400

On the front panel of EH-2400, there are Power, Collision, Jabber, utilization LEDs. For each

RJ-45 STP port, there are two LED indicators - TX/RX LED and Partition LEDs. These

LEDs help in diagnosing line troubles and indicate the status of data transmission.

Figure 2-1 Front Panel of EH-2400

LED indicator

LEDs Status Description

Power Steady Green Indicates hub is power on

Collision Blinking Orange Blinks when network collision are detected

Jabber Blinking Red Blinks when network jabbers are detected

TX/RX Steady Green Indicates Link integrity pulses are being received

Blinking Green Blinks when data is received or transmitting

LEDs Status Description

AUI Blinking Green Blinks when data is receiving / transmitting

BNC Blinking Green Blinks when data is receiving / transmitting

Utilization Steady

Green

Yellow

Amber

Red

Utilization levels change from 5% to 70% as network

level changes

Rear Panel of EH-2400

As shown in Figure 2-2

Figure 2-2 Rear Panel of EH-2400

One Power switch, power connector and one BNC, AUI connector for 10Base-2 and 10Base-

5 network.

CHAPTER 3

INSTALLATION

Getting Ready to Install the EH-2400

Power Requirement

EH-2400 is designed with full range power supply. Make sure you power is in the range 90to

260VAC at 50 to 60 Hz. This device require 15 Watts for operation and 10 Watts for stand-

by.

Prepare to Install EH-2400

EH-2400 support 24-port 10Base-T, one port BNC, and one port AUI connection. Extra

UpLink port for hub cascade. Each port is printed with its port number on the location.

STP port and STP/UTP Cable

Connect port 1 to port 24 with non cross-over cable to any LAN cards. If connect to a hub through port 1

to port 24, a cross-over cable is required. Users can use a non cross-over cable to cascade to another hub

through “UpLink port”. Users should use ONLY ONE of these two port at the same time. Plug two

twisted-pair cable to these two ports will cause this hub malfunction.

The STP/UTP cable should be 22, 24, or 26 AWG with a minimum of one twist per foot. 24 AWG is

recommended. The cable should have a nominal impedance of 100 ohms at 10 MHz, a maximum segment

loss of 11.5 dB between 5 and 10 MHz, and a maximum end-to-end propagation delay of 1 microsecond.

You can use a STP/UTP cable that complies with AT&T's Premises Distribution System (PDS) wiring

standard.

BNC port and Coaxial Thin Cable

EH-2400’s thin coaxial port can be connected to either a computer or another hub. In order to user the

thin coaxial port, you will need one thin coaxial cable, two 50-ohm terminators and T-connectors.

Thin coaxial cable is a 50-ohm coaxial cable with a copper or tinned center conductor, solid inner

dielectric (insulating material), and braided wire (not foil) shielding. It can be an RG-58, RG-58/A, RG-

58/U, or RG-58A/U cable.

AUI port

The AUI port of EH-2400, beside the feature of BNC port, can be connected to external transceivers, like

AUI to BNC, AUI to TP, or AUI to fiber-optic transceiver, and then connected to a computer, a hub or

another repeater.

EH-2400 Installation

Follow the instructions below to set up EH-2400.

Step 1.Select a suitable place to put the hub or to install. Make sure there is an AC outlet nearby.

Step 2. Power off all of the computers, hubs, or other devices that will be connected to the hub.

Step 3. Connect the power cord to the hub and AC outlet on the wall.

Step 4. Power on the Power switch on the rear panel. The power LED should light up.

Step 5. Connect all the cables and connectors.

Connecting the Hub to AC Power

After making network connections as described in the preceding sections, you are ready to plug the hub in and

turn it on.

The input voltage is from 90 to 240 volts AC and any frequency from 50 to 60 hertz. Adjustment to the power

source is automatic; there is no switch to set.

Before plugging the hub in, make sure the power cord

(1) is long enough to reach an AC wall outlet of an approved type,

(2) has plugs that match both the hub's power inlet and the type of wall outlet you will use, and

(3) Conforms to safety regulations in your area.

In most parts of the world you must use a three-conductor power cord with an integral three-prong grounding

plug.

If the supplied power cord does not meet all three requirements given above, contact your computer equipment

dealer and obtain one that does. Do not use an extension cord or multi-socket adapter; do not attempt to use a

cord designed for any other kind of power inlet or wall outlet; do not use a cord that fails to meet safety

standards in your part of the world.

Power Failure

To prevent costly equipment damage and downtime, please consider installing a surge suppression device

or a UPS (un-interrupted power supply).

CHAPTER 4

TROUBLESHOOTING

SYMPTOM: The power LED is not lit.

SOLUTION:

If the power LED is not lit after the power cord is plugged into the concentrator

and the power outlet, there may be a power fault.

1.First verify if there is power at the power outlet by plugging in a device which is

known to operate.

2.If a volt meter is available, measure the voltage on the power outlet.

3.If a volt meter is not available and the second power adapter does not fix the

problem, contact the authorized dealer from whom you purchased your

concentrator for assistance.

SYMPTOM: The Link LED is not lit.

SOLUTION:

The Link LED is not on after a workstation is connected to the STP port of the

concentrator.

1.Verify if the workstation and the concentrator are powered up.

2.Verify if the network cable has been attached to the workstation.

3.Verify if the network cable from the Hub to workstation is straight-through and is

not cross-over.

4.Verify if the wires to the phone jack pins are connected correctly and the

connections are not faulty.

SYMPTOM: When port auto-partitioned out.

SOLUTION:

1.Use another Ethernet adapter to verify if the original Ethernet adapter

malfunctions.

2.Connect the twisted-pair cable to another concentrator to verify if the twisted-pair

cable can work well.

CHAPTER 5

PRODUCT SPECIFICATION

Standard

Compliance : Ethernet 10Base-2/5/T

Media Supported : Category-3/4/5 STP/UTP cable

Thick Cable

RG-58 coaxial cable

Interface : 24-port 10Base-T STP port

1-port 10Base-T UpLink port

1-port AUI port

1-port BNC port

LEDs : 1-Power, collision, Jabber LED

8-Utilization LEDs

24-TX/RX LEDs

24-Partition LEDs

Power System : 90~260 VAC, 50~60Hz

Power

Consumption : 15W maximum, 10W typical

Dimension : 430 x 133 x 44.5 mm

Weight : 1.5 Kg

Temperature : 0~55 degree C (Operation)

-10~70 degree C (Storage)

Humidity : 10%~85% (Operation)

5 %~ 90% (Storage)

EM-2400V2

Indice

Altri manuali Planet Router di rete

Planet

Planet SW-504 Manuale utente

Planet

Planet IAD-300 Manuale utente

Planet

Planet ISW-800M Manuale utente

Planet

Planet AND-4102 Manuale utente

Planet

Planet FRT-420SN Manuale utente

Planet

Planet FGSW-1822VHP Manuale utente

Planet

Planet IGS-5225-16T4S Manuale utente

Planet

Planet WGS3-2820 Manuale utente

Planet

Planet VR-300 Series Manuale utente

Planet

Planet GSW-1600HP Manuale utente

Planet

Planet FNSW-1600S Manuale utente

Planet

Planet RT-101 Manuale utente

Planet

Planet ADE-4100 Manuale utente

Planet

Planet ADSL 2/2+ VPN Firewall Router ADW-4302A v2 Manuale utente

Planet

Planet FNSW-4800 Manuale utente

Planet

Planet ADE-3410v4 Manuale utente

Planet

Planet WNRT-627 Manuale utente

Planet

Planet SW-502 Manuale utente

Planet

Planet GRT-101 Manuale utente

Planet

Planet FGSW-2620VM Series Manuale utente

Planet

Planet GS-4210-24P2S Manuale utente

Planet

Planet FNSW-1600S Manuale utente

Planet

Planet 802.11g Wireless Access Point / Bridge... Manuale utente

Planet

Planet WGSW-2620PV Manuale utente

Manuali Router di rete popolari di altre marche

Allnet

Allnet ALL0333AU Manuale utente

HomeSeer

HomeSeer HT-SEL Manuale utente

Sercomm

Sercomm Genesis OC3505D Manuale utente

Billion

Billion BIPAC 5102 Series Manuale utente

TP-Link

TP-Link TD-8817 Manuale utente

Motorola

Motorola MR1900 Manuale utente

Digi

Digi IX14 Manuale utente

Cisco

Cisco NCS 540 Manuale

XAVi

XAVi X8821e Manuale utente

BEC

BEC 6200WZL Manuale utente

MikroTik

MikroTik hAP ac3 Series Manuale utente

Korenix

Korenix JetNet 5428G Series Manuale utente

NETGEAR

NETGEAR FS526T - Switch Manuale utente

Korenix

Korenix JetNet 5710G Series Manuale utente

Automated Logic

Automated Logic ZN551 Manuale del proprietario

Cisco

Cisco ASR 1000 Series Manuale dell'operatore

EnGenius

EnGenius ESR-9710 Manuale utente

Cisco

Cisco 805 Series Istruzioni operative e di sicurezza