Planet WNAP-3000PE Manuale utente

802.11n Enterprise PoE Access Point

WNAP-3000PE

Quick Installation Guide

Table of Contents

Package Content.............................................................................................. 3

Physical Details................................................................................................ 4

Front panel ................................................................................................ 4

LED denition............................................................................................. 4

Back Panel ................................................................................................ 5

Hardware Installation ....................................................................................... 6

General installation ..................................................................................... 6

PoE installation........................................................................................... 6

Web Conguration ........................................................................................... 7

Further Conguration ....................................................................................... 8

Package Content

WNAP-3000PE x 1

2dBi Dipole Antenna x 3

Power Adapter x 1

Quick Installation Guide x 1

CD-ROM x 1

Note

If any of the above items are missing or damaged, contact your

local dealer for support.

Physical Details

Front panel

LED denition

Power On - Normal operation.

Off - No power

WLAN

On - Idle

Off - Wireless connection is not available.

Flashing - Data is being transmitted or received via the Wireless

access point. Data includes “network trafc” as well as

user data.

Status

On - Error condition.

Off - Normal operation.

Blinking - During start up, and when the Firmware is being

upgraded.

LAN

On - The LAN port is active.

Off - No active connection on the LAN port.

Flashing - Data is being transmitted or received via the

corresponding LAN port.

Back Panel

Reset Button

This button has two (2) functions:

Reboot - When pressed and released, the Wireless Access

Point will reboot (restart).

Reset to Factory Defaults - This button can also be used to

clear ALL data and restore ALL settings to the factory default

values.

To Clear All Data and restore the factory default values:

1. Hold the Reset Button until the Status (Red) LED blinks

TWICE, usually more than 5 seconds.

2. Release the Reset Button.

The factory default conguration has now been restored,

and the Access Point is ready for use.

LAN Use a standard LAN cable (RJ45 connectors) to connect this

port to a 10/100/1000BaseT hub/switch on your LAN.

Power Connect the supplied power adapter (12VDC @1A) here.

Hardware Installation

General installation

1. Locate an optimum location for the WNAP-3000PE. The best place for your

WNAP-3000PE is usually at the center of your wireless network, with line of sight

to all of your mobile stations.

2. Assemble the antennas to WNAP-3000PE. Try to place them to a position

that can best cover your wireless network. The antenna’s position will enhance

the receiving sensitivity.

3. Connect RJ-45 cable to WNAP-3000PE. Connect the “LAN” port of WNAP-

3000PE to your LAN switch/hub or a single PC.

4. Plug in power adapter and connect to power source. After power on,

WNAP-3000PE will start to operate.

5. Check the LEDs:

The Status LED should ash, then turn OFF.

The Power, Ethernet and WLAN LEDs should be ON.

For more information, please refer to LED deication.

Note

1. ONLY use the power adapter supplied with the WNAP-3000PE.

Otherwise, the product may be damaged.

2. Use only one power source for WNAP-3000PE, use of both

power sources, i.e. 12VDC and 802.3af PoE, at the same time

may cause the device faulty.

PoE installation

1. Do not connect the supplied power adapter to the WNAP-3000PE.

2. Connect one end of a standard (category 5) LAN cable to the Ethernet port on

the WNAP-3000PE.

3. Connect the other end of the LAN cable to the powered Ethernet port on a suit-

able PoE Adapter or switch. (IEEE 802.3af compliant)

4. Connect the unpowered Ethernet port on the PoE adapter to your Hub or switch.

5. Connect the power supply to the PoE adapter and power up.

6. Check the LEDs on the WNAP-3000PE to see it is drawing power via the Ethernet

connection.

Web Conguration

WNAP-3000PE provides a user friendly interface for users to congure it via web

browser. Please follow the steps below to congure WNAP-3000PE basic settings.

1. The default value of WNAP-3000PE doesn’t enable DHCP server, please

double check obtain the IP from DHCP server in your network, otherwise,

please congure static IP address in your PC to an unused value in the range

192.168.0.1 ~ 192.168.0.254, with a Network Mask of 255.255.255.0.

2. Open your web browser and type WNAP-3000PE default IP address

http://192.168.0.228 into the “Address Field” of you web browser.

3. After enter the IP address and press Enter key, you can see the dialog box

appear as below, please enter the User name and Password. Then press “OK”.

User name: admin

Password: password

Further Conguration

If you want to congure WNAP-3000PE with more detail settings, please refer to

our manual in the CD-ROM and congure with your Web Browser. If you have any

difculty on resolving the problem while installing or using WNAP-3000PE, please

contact with your local dialer or feel free to contact PLANET for support.

Altri manuali per WNAP-3000PE

Indice

Altri manuali Planet Punto di accesso wireless

Planet

Planet WDAP-850AC Manuale utente

Planet

Planet WNAP-7205 Manuale utente

Planet

Planet WAP-252N Manuale utente

Planet

Planet WNAP-6305 Manuale utente

Planet

Planet MAP-3100 Guida rapida

Planet

Planet 802.11n Wireless Access Point WNAP-1120 Manuale utente

Planet

Planet WAP-4036 Manuale utente

Planet

Planet WDAP-C1750 Manuale utente

Planet

Planet WNAP-6305 Manuale utente

Planet

Planet WAP-4033 Manuale utente

Planet

Planet WDAP-702AC Manuale utente

Planet

Planet WAP-7000 Manuale utente

Planet

Planet WNAP-6306 Manuale utente

Planet

Planet WNAP-W2200UE Manuale utente

Planet

Planet 802.11n Wireless Access Point WNAP-1120 Manuale utente

Planet

Planet WAP-900 Manuale utente

Planet

Planet Wireless Access Point w/Bridge WAP-1963A Manuale utente

Planet

Planet WNAP-6350 Manuale utente

Planet

Planet WAP-1963 Manuale utente

Planet

Planet WAP-1965 Manuale utente

Planet

Planet WDAP-C7210E Manuale utente

Planet

Planet WDAP-C1750 Manuale utente

Planet

Planet Network Device WAP-4033PE Manuale utente

Planet

Planet WNAP-6325 Manuale utente

Manuali Punto di accesso wireless popolari di altre marche

D-Link

D-Link DWL-2100AP - AirPlus Xtreme G Manuale utente

Ubiquiti

Ubiquiti NanoStation NSM2 Manuale utente

Cisco

Cisco Aironet 1550 Series Manuale utente

Aruba

Aruba IAP-335 Manuale utente

Advantek Networks

Advantek Networks AWN-AP-54MR Manuale utente

IP-COM

IP-COM AP355 Manuale utente

Buffalo

Buffalo AirStation WLA-L11G Manuale utente

EnGenius

EnGenius EnStationACv2 Manuale utente

D-Link

D-Link DAP-3662 Manuale utente

xG Technology

xG Technology xMax CN1300 Manuale utente

Widelink

Widelink ezWave WAP-1100 Series Manuale utente

Edimax

Edimax CAP1200 Manuale utente

Ubiquiti

Ubiquiti LBE-5AC-Gen2 Manuale utente

Aruba

Aruba AP-203R Manuale utente

LuXout Shades

LuXout Shades LUXSHADE MOTION Manuale utente

CreatComm

CreatComm TB5F Manuale utente

SineDigital

SineDigital MW-1500AP(H) Manuale utente

TP-Link

TP-Link AP9650 V1 Manuale utente