Planex Cloud Connect CS-W06N Manuale utente

CS-W06N

Planex Cloud Connect

CS-W06N

Table of Contents

1. INTRODUCTION..........................................................................................................................4

2. HARDWARE DESCRIPTION AND QUICK INSTALLATION/USAGE ................................6

2.1. MAJOR HARDWARE COMPONENTS.......................................................................................6

2.2. QUICK INSTALLATION AND USAGE ........................................................................................8

2.3. WIRELESS CONNECTION (IF ROUTER/AP HAS WPS BUTTON)..........................................12

2.4. WIRELESS CONNECTION (IF WPS NOT SUPPORTED ON ROUTER/AP)..............................12

2.5. PUSH NOTIFICATION ............................................................................................................13

3. WEB CONFIGURATIONS........................................................................................................15

3.1. INFORMATION ......................................................................................................................16

3.2. VIDEO DISPLAY ...................................................................................................................17

3.3. NETWORK............................................................................................................................18

3.4. WIFI SECURITY....................................................................................................................19

ADVANCED NETWORK.......................................................................................................................21

3.5. VIDEO SETTINGS.................................................................................................................22

3.6. MOBILE VIDEO SETTINGS....................................................................................................24

3.7. NIGHT MODE CONTROL .......................................................................................................25

3.8. EMAIL/FTP ALARM ...............................................................................................................26

3.9. SPEAKER ALARM SETTINGS ...............................................................................................29

3.10. NAS SETTINGS....................................................................................................................30

3.11. SD-CARD SETTINGS ...........................................................................................................32

3.12. SCHEDULING .......................................................................................................................34

3.13. LED DISPLAY CONTROL......................................................................................................36

3.14. DATE/TIME...........................................................................................................................37

3.15. ADMIN..................................................................................................................................38

3.16. UPGRADE ............................................................................................................................39

3.17. REBOOT...............................................................................................................................40

3.18. SET TO FACTORY DEFAULT..................................................................................................41

4. FEATURES AND SPECIFICATIONS......................................................................................42

4.1. FEATURES ...........................................................................................................................42

4.2. SPECIFICATIONS..................................................................................................................43

APPENDIX A. MAXIMUM ALLOWED VIDEO USERS.................................................................45

APPENDIX B. PERFORMANCE INFORMATION .........................................................................46

APPENDIX C. TROUBLE SHOOTING............................................................................................48

CS-W06N

APPENDIX D. SNAPSHOT PICTURE ON ANY BROWSER.......................................................50

CS-W06N

1. Introduction

The IP Camera is designed for all day video surveillance on your

iPhone/iPad and Android mobiles/pads. The setup is truly 1-2-3 :

1. Connect the camera to the network

2. Download the app Touch2See into your iPhone/iPad or Android

3. View video by the camera ID/password

The push notification is supported, so that you will get the notification from

your iPhone/iPad and Android once there is any events detected through the

PIR body sensor or sound detector on the camera, even when your mobile is

on sleep mode.

The SD card recording is supported, and you could playback the recorded

video on your iPhone/iPad and Android. You could also do the SD card

recording only when there is PIR or sound detection to save the SD card

storage size. The PIR and sound detected recording has a 5 seconds

pre-recording, so that you will always catch the critical moment.

For day & night usage, there are two video sensors/lens on the camera,

one for day and one for night. The day lens and night lens focus are separately

tuned for day light and Infra Red light for best video quality. No ICR, no

mechanical problem.

Two-way audio is supported. You can monitor the synchronized

video/audio and talk to or warn the people around the camera from your

iPhone/iPad and Android once you got the push notification. The speaker jack

is supported so that you could connect any high power speaker to the camera

for your needs.

The WPS(WiFi Protected Setup) is supported. You could set up the WiFi

connection of the camera with the router by clicking the WPS button on the

camera and on the router at the same time. No more complicated WiFi

configuration.

The IP Camera is ideal for securing small businesses, home offices and

residences. The IP Camera is a perfect replacement of the alarm system and

CS-W06N

baby monitor in your house and shop. .

The differences

It’s very easy to see the video of the Day&Night IP Camera, you only need to key

in the ID/Password of the IP CAM any where in the world, you do not need to

remember the IP address or domain name or DDNS name or port number. And you

do not need to modify the settings(like port mapping, fixed IP, DDNS, virtual server) of

the NAT/router devices, it’s just a plug & play usage.

CS-W06N

2. Hardware description and quick installation/usage

The IP CAM is designed to be very easy to install and use. First, let’s see the

major components of the IP CAM products.

2.1. Major hardware components.

The major components on the front panel of the IP CAM products are the built-in

microphone, lens and LEDs :

1. Microphone – for receiving the audio/voice. Effective distance is about 5 meters.

2. Lens – the lens is inside the camera body and the focus of the lens is fixed, you do

not need to spend time to adjust the focus, the effective focus range is from 30cm

to infinity. There are two lens for day and night usage separately.

3. Status indication LED (red) – this LED is to indicate the Internet connection status.

When the Internet connection is connected, the LED will be constant red light. If

there is any Internet connection problem, the LED will be blinking red light.

4. Ethernet indication LED (blue) – this LED is to indicate if the Ethernet link is ok

and packet traffic is sending/receiving. When the Ethernet cable is connected, the

LED is on. When there is packet sending/receiving, the LED is blinking blue light.

5. SD card indication LED(yellow) – this LED is to indicate the status of the Micro-SD

card recording, it will be on when the Micro-SD card is inserted and will blink

during recording.

6. Micro-SD card slot – for inserting the Micro-SD Card. (support up to 32G bytes)

7. WPS button – this is to automatically synchronize the WiFi settings with a WPS

capable WiFi router.

8. Speaker jack – connect to an external speaker for two way audio and speaker

alarm usage.

9. PIR sensor – for the detection of the human body.

10. IR LED – for the Infra Red lighting of the night mode usage.

CS-W06N

Figure 2-1: Major components in the front and side panel

The major components on the back panel of the IP CAM products are the bracket

screw jack, power jack, Ethernet jack and reset button:

1. Bracket screw jack – this is the position to screw in the bracket of the IP CAM.

With the bracket, you can put the IP CAM on the desk, on the wall or on the

ceiling.

2. Power jack – this is the place to plug in the power adaptor. The power needed for

this IP CAM is 12V/1.0A, please make sure you are using the correct power

adaptor.

3. Ethernet jack – this is the place to plug in the RJ45 Ethernet cable. When the

Ethernet link is ok, the Ethernet indication LED on the front side will be blue light.

4. Reset button – this is the button to reset the IP CAM to default factory settings.

You need to use a small stick like pencil or tooth stick to press the reset button for

more than 3 seconds to enable the reset function. Usually when you forgot the

administrator account, you will probably need to do this reset action to reset to the

default factory settings. Please refer to section 3.19 for more details.

CS-W06N

Figure 2-2: Major components in the back and bottom panel

2.2. Quick installation and usage

There are only three things that you need to do to see the video from the IP CAM.

1. Connect the IP CAM to the home/office network.

2. Install the Touch2See software on the notebook/PC.

3. Key in the ID/password of the IP CAM(from the ID/Password card) on the

Touch2See, and then you can see the video.

First, Connect the IP CAM to the home/office network

Please connect the IP CAM accessories to the IP CAM body correctly, including

the power adapter and Ethernet cable. And connect the other end of the Ethernet

cable to the home network or office network. Usually, this Ethernet cable is plugged

into a home NAT/router device or an Ethernet switch if in the office, as shown in

Figure 2-4. Since the default settings of the IP CAM use DHCP function and very often

there is a DHCP server on most of the Home/office network, the IP CAM should be

connected to the Internet immediately. The Internet status LED is constant red light to

indicate this good connection status. If the LED is blinking, please refer to section

3.3~3.5 to try other network settings.

CS-W06N

Figure 2-4: Connect Ethernet cable to a switch/router.

Second, Install the Touch2See software on the notebook/PC

Please download Touch2See from Web site, and install it on your notebook or

personal computer (must be running Microsoft Windows OS).

Windows 7 : http://www.planex.com.tw/FileHandler.ashx?id=1248

Windows XP/Vista : http://www.planex.com.tw/FileHandler.ashx?id=1250

Execute the program Touch2SeeInstaller-xxx.exe on the disk. The program will

pop-up some windows about the installation options, please press the “next” button to

proceed with the installation. After the installation is complete, there will be a

Touch2See icon on the desktop of your computer screen, please execute this icon.

The Touch2See program will run immediately.

Third, Use Touch2See program to see the video

If the computer and IP CAM is connected to the same network, the IP CAM ID

will be displayed in the “Auto Search” list. You can double click the “Auto Search” to

search all the connected IP CAMs any time. The only thing left right now for seeing

the video is to double click the IP CAM ID item in the “Auto Search” list.A window

asking for password input will pop up. Please key-in the password in your

ID/Password card into this field and click “ok”. The video will then be displayed on the

window.

CS-W06N

Figure 2-6: The ID/Password card

Notice 1:

1. You can modify this play-video password by entering into the web configuration

pages. Please refer to section 3.6 for more information.

2. You can also add the IP CAM into the CameraList in the Touch2See software to

have more convenient video display, please refer to the user manual of the

Touch2See software for more functions.

Seeing the video in a remote location

After the IP CAM is installed and you can see the video from the Touch2See

software in the local network, it’s very easy to see the video in a remote location. All

you need to do is add a camera item in the “CameraList” folder of the Touch2See

software, key in the IP CAM ID and Password(from the ID/Password card). And then

double click this camera item. You will then see the Camera video immediately. No

further NAT/router setting modifications are needed.

Indice

Altri manuali Planex Telecamera IP

Planex

Planex CS-W02G2 Manuale utente

Manuali Telecamera IP popolari di altre marche

FLIR

FLIR Exx series Manuale utente

Avigilon

Avigilon H4A-BO1-IR Manuale utente

Digital Watchdog

Digital Watchdog DWCA-C128-64 Manuale utente

ShareTech

ShareTech AV1 Manuale utente

Ezviz

Ezviz C6C Manuale utente

Melchioni

Melchioni UCAM 2015 Manuale utente

Geutebruck

Geutebruck G-Cam/ESD-4630 Manuale utente

Arecont Vision

Arecont Vision MegaBall AV3146DN-3310-D-LG Manuale utente

Mitel

Mitel 6800i Series Manuale di servizio

Vitek

Vitek VTC-IR403-212NP Manuale utente

THOMSON

THOMSON DSC - 323W Manuale utente

AVer

AVer FB2027 Manuale utente

ENFORCER

ENFORCER EV-T5105-N2SQ Manuale utente

Wansview

Wansview NC543 Manuale utente

Eneo

Eneo MCB-64A0003M0A Manuale utente

deView electronics

deView electronics CBDNI36F Manuale utente

Swann

Swann SwannEye Manuale utente

LevelOne

LevelOne IP CamSecure Manuale utente