PLANUS WAVE Manuale utente

1
MACERATOR TOILET
WC CON TRITURATORE
REGISTER YOUR PRODUCT:
WWW.PLANUS.EU
WAVE
-
STILOPLUS

2
INDEX
1. INSTALLATION WARNINGS: ……………………………….....… 03
2. WARNINGS AND PRECAUTIONS FOR USE: .......................... 03
3. DIMENSIONS: …………………………………………….….…….. 04
4. TECHNICAL DATA: ……………………….………..……………... 05
5. PRINCIPLE OF OPERATION: …………………….………………. 06
6. ACCESSORIES …………………………….……….……………… 07
7. INSTALLATION: ……………………….…………….…….….….... 08
8. MAINTENANCE OF THE PRODUCT: ….………………………… 09
9. WARRANTY CONDITIONS: ………………….…………….…...… 18

3
1. WARNINGS AND PRECAUTIONS FOR INSTALLATION
• The device must be installed only by qualified personnel and can
only be used following the correct installation carried out as indi-
cated in this booklet.
• The apparatus shall be powered by a network protected by a
differential switch having a maximum permissible current diffe-
rence not exceeding 30mA.
• It is advisable to provide a power outlet for the exclusive use by
the appliance.
• If the power cord is damaged, it must be replaced by the manu-
facturer or by similarly qualified personnel.
• During installation and before performing any maintenance, ma-
ke sure that the power cord is not connected.
• In case of malfunction, disconnect the power plug and avoid
using the toilet. For "All-in-one" versions, avoid using utilities
connected to the main exhaust sleeve.
2. WARNINGS AND PRECAUTIONS CONCERNING USE
• This appliance is for domestic use only.
• The device is designed to drain only toilet paper and organic
residues. Avoid throwing in foreign objects that can damage it
(such as: cloth, condoms, absorbents, make-up wipes, plastic or
metal objects, food or other solid kitchen residues, etc.).
• Children and all persons with reduced or inexperienced physical,
sensitive or mental abilities may not use the appliance unless
supervised or properly instructed by a person responsible for
their safety.
• In case the house or the bathroom is not used for a long time
(holidays or other) it is advisable to close the general entrance of
the water.
• Solvents or other chemicals can damage the appliance.
• In case of prolonged use, the thermal disconnector to protect the
appliance will automatically stop the power supply of the engine
if it overheats. In this case, disconnect the power supply and
then reconnect it after a break of about 30-60 minutes. The ap-
pliance will return to normal operation.

4
3. DIMENSIONI / DIMENSIONS (mm)
WAVE
STILO PLUS

5
4. DATI TECNICI / TECHNICAL DATA
Caratteristica della pompa:
Tensione di alimentazione / Power Supply AC 220-240V, 50Hz
Assorbimento / Power 600W
Grado di protezione / Degree of Protection IP55
Norme/Standards EN 60335-1
EN 60335-2
EN 12050-3
Prevalenza / Prevalence 4 m
Consumo di acqua / Water Consuption 3 Lt / 1.8 Lt
Diametro tubo di scarico / Discharge Hose ø 40 mm

6
5. PRINCIPLE OF OPERATION
• The system is operated by a button on the side of the toilet. Once pres-
sed, the operating cycle of the sanitary with macerator is structured as
follows:
• A quick push of the button starts the cycle with reduced water consump-
tion (ECO). Keeping the button pressed for longer increases the amount
of water used in the rinsing and filling phases (MAX 3lt.).
FLUSH
FLUSH
+
DISCHARGE PHASE OF THE PUMP
ADDITION OF CLEAN WATER

7
6. ACCESSORIES
ITEM QUANTITY (Pz.)
HOSE HOLDER Ø 40mm 1 (+1*)
CLAMP 32/50 W2 2 (+2*)
FLEXIBLE PIPE Ø 40mm 1 (+1*)
CAP Ø 40mm 1*
FILTERT 3/4” FOR HOT WATER 1
GROUND FIXING 2
*solo versione All-in-One
Connection for additional
INLET
(Only
All in One version)

8
7. INSTALLATION
• Electrical connection
It is necessary to prepare the connection to the home network
(230vac) according to current regulations.
• Hydraulic connection:
The system does not require a drain box. Connection to the domestic cold
water line is required.
For the attack position refer to diagram the following for the predispositions.
The indicated positions are indicative, being flexible fittings.

9
• Indications and preliminary suggestions
In order to realize a wire-wall installation, with not visible tubes it is suggested
the creation of a wall (preferably plasterboard), to create a gap suitable for the
passage of the pipes.
Then create a special frame (1) for the wall.
Prepare the discharge line (Ģ 40mm). It is suggested the use of rigid pipes in
PVC Ơ40mm. First make the ascending section (2), then through a softened
curve (3) realize the horizontal section, with a minimum slope of 1%. It is re-
commended in this section to provide for an increase in the section (4), until
reaching the ventilated sewer descending.
For the "All-in-One" versions, prepare the piping (5) for collecting the
waste water from additional utilities, connected to it (6). Ensure a slope of 3%.
NOTE for "All-in-One" versions:
In case of non-use of the additional inlet it is necessary to seal it with the sup-
plied 40cap. Tighten with a collar (clamp).
Prepare a tap with thread M 3/4" for connection to the domestic water supply
(cold water), which will be used for rinsing the toilet.
For only the "KB" version of the Stilo Plus, similarly arrange 2 taps with M1/2
thread" for the connection of the hot and cold water hoses of the integrated
bidet kit.

10
• Indications and preliminary suggestions
Place the toilet in the chosen point and draw with a pencil the profile of the
foot (1), also marking the position of the holes for fixing to the ground (2).
Move the toilet and, at the marks for the position of the hardware on the
ground, place the provided fixing brackets (1), taking care to leave enough
space for the thickness of the ceramic (at least 15mm).
Then fix the brackets to the ground with the dowels.
Questo manuale è adatto per i seguenti modelli
1
Indice
Altri manuali PLANUS Toilette
Manuali Toilette popolari di altre marche

Better Bathrooms
Better Bathrooms BUN/BeBa 27555/78725 Manuale utente

American Standard
American Standard CONCEPT Cube TF-2704 Manuale utente

BIOLAN
BIOLAN ECO Manuale elenco delle parti

Thetford
Thetford C260 Series Manuale utente

KELISS
KELISS T162A Series Manuale utente

Kohler
Kohler K-22241K Istruzioni per il montaggio












