Plockmatic SR85 Cover Feeder Manuale utente
(5)
T09149
INSTALLATION INSTRUCTION SR85 TO MODEL 306/310
PURPOSE:
By means of a connection kit enable the SR85 booklet maker to work in line with the
Model 306/310 collator. The kit will not affect the normal operation of the SR85 to the
copier/printer.
Kit contents:
Description Part no Qty
Label, scale 75646 1 pce
Label, arrow 75261 1 pce
Microprocessor 761009-5.02 1 pce
Connection cable 760006 1 pce
Base to Collator 900024 1 pce
Installation instruction 75952 1 pce
Upgrade the software in SR85 if the software is below V5.02. Follow below procedure:
1. Switch off main power.
2. Remove rear cover.
3. Remove the microprocessor by using an Extractor tool. Read Caution below.
4. Insert the new microprocessor with the dot “A” positioned corresponding
to the arrow “B”.
5. To reset the EEprom, move the DIPswitch no. 1 on the controller PCB to the right
(right when facing the PCB).
6. Switch on the main power.
Note: The ADJUST LED on the control panel is flashing.
7. When the ADJUST LED stops flashing, switch off the main power.
8. Move the DIP switch no.1 on the controller PCB to the left ( left when facing the PCB)
9. Mount the rear cover.
10. Switch on the main power.
Caution: Always handle the circuit board in accordance
with electrostatic discharge procedures. The circuit
board and microprocessor are sensitive to ESD damage.
Normal mode < > Reset EEPROM
AB
November 2001
Part no. 75952 1
(5)
T09149
2
Height adjustment:
1. Push the machines together.
2. Place a scale (1) on the stainless plate (2) on the infeed unit at SR85. Adjust the
height to approximately 15 mm to the lower edge of the door of Model 306/310 by
adjusting the height on the castors of the Collator base.
Note: Do not adjust the height of the SR85.
Approx.15 mm 1
2Door
(5)
T09149
Attaching the labels:
1. Clean the surface where the labels should be placed.
2. Use the inner edge of the main frame on Model 306/310 as reference point when
placing the labels.
3. Place the label (1) on the door 130 mm from the inner edge of the main frame and use
the green A4 mark as reference.
4. Place the small label (2) on the stainless plate of SR85 85 mm from the outer edge of
the infeed unit and use the green mark as reference.
1
2
3
Main frame
(5)
T09149
Install the Model 306/310 to SR85.
1. Switch off the main power switch.
2. Disconnect the communication cable between the copier finisher
and SR85.
3. Roll the SR85 off the rails and place the SR85 against the Model
306/310.
4. Mount the communication cable (1) between Model 306/310 and
SR85 .
5. Switch on the main power switch.
1
4
(5)
T09149
Communication
cable between the
copier finisher and
the cover feeder.
Communication
cable between the
cover feeder and
the booklet maker.
Install the Model 306/310 to SR85 with fover feeder.
1. Switch off the main power switch.
2. Disconnect the communication cable (2) between the copier
finisher and the cover feeder.
3. Disconnect the communication cabel (1) from the SR85. It is not
necessary to disconnect the connector from the cover feeder.
4. Roll the SR85 off the rails and place the SR85 against the Model
306/310.
5. Mount the communication cable (3) between Model 306/310 and
SR85.
6. Switch on the main power switch.
3
5
12
Altri manuali per SR85 Cover Feeder
2
Questo manuale è adatto per i seguenti modelli
2
Indice
Altri manuali Plockmatic Stampante
