PMI Ventilator Manuale utente
Instructions > PMI Ventilator
REMOVAL FROM SERVICE
The PMI Ventilator provides the protection you need working in
a vertical rope world. It features a Kevlar shell giving your head
maximum protection. It meets ANSI Z89.1, Type 1 Fully adjustable
three point chinstrap and ratchet system provide a perfect fi t.
Weight: 1.13 lbs (513 g)
If any of the following occur, this helmet must be removed from service
and destroyed:
• If the helmet received a signifi cant impact.
• If the helmet shows cracks that are more than superfi cial.
• If any part of this helmet shows signifi cant damage or excessive wear.
• If the helmet is has been visibly damaged by heat, chemicals, etc.
• If this helmet has been in service for 5 years, regardless of condition.
• If this helmet cannot be properly adjusted.
INSPECTION
MAINTENANCE AND CARE
Inspect the helmet for obvious damage. Check the shell for cracks
and dents. Minor surface cracks will not impair the effectiveness of
this helmet. Check the webbing and buckles for damage or excessive
wear.
This helmet should be assigned to a single user who is responsible for
inspecting it after each use. Make sure that the surface of the helmet
has no dents or signifi cant cracks. Inspect the webbing and buckles
for damage or excessive wear. If needed, wash the helmet with clear
water or a mild soap, such as PMI Rope Soap. Ordinary laundry
detergent, or solutions that may contain bleach, should not be used on
life safety gear.
Air dry in a cool, dry place out of direct sunlight. Store the helmet in
a cool place where it will be protected from exposure to potentially
damaging chemicals. Repair or modifi cation of this product without
the manufacturers written consent is strictly forbidden. You should
establish a record of the inspections of this equipment. You may need
to develop your own inspection log format depending on your needs.
HELMET TECH INFO
A comfortable, well-fi tting helmet that is designed specifi cally for
vertical work is essential. Helmets must have a secure chin strap and
a three-point suspension to keep the helmet on the head when it is
needed most. A three point suspension refers to a helmet with webbing
support points on both sides of the helmet and one at the rear. The
chin strap should also be designed so that a relatively high force is
required to cause a release. This helps keep the helmet on the user’s
head in a tumbling fall. The inside suspension of the helmet should hold
the shell away from the skull during a blow to the helmet and should
provide air circulation and comfort, particularly during hot weather.
The shell should have the rigidity to resist impact to the helmet and
penetration by sharp objects but be fl exible enough to absorb some
of the blow that otherwise would be directly transmitted to the skull
and spine.
The design of the helmet should protect the head against objects
falling from above and hitting from the side. A slight brim helps
prevent rainwater or spray from dripping into your face. However,
your helmet should have a narrow enough profi le to allow you a good
upward fi eld of vision and to ensure that the back of the helmet does
not catch on a backpack when you raise your head.
This helmet is not designed to provide protection from the following hazards:
non-ionizing radiation, ionizing radiation, external radiation or any condition
not expressly stated in this use information.
CERTIFIED ANSI Z89.1, Type 1
WEBV1-0411
PMI LIMITED WARRANTY
PMI products are warranted to the original retail purchaser to be free from defect in material and workmanship for a period of one year. PMI will repair or replace the item without charge provided
inspection at our factory discloses no misuse or alteration, which, in our judgment, has affected the condition or functioning of the product. All implied warranties imposed by law in connection with the sale
of PMI products are also limited in duration to a period of one year. PMI expressly excludes and shall not be liable for any consequential damages arising out of any breach of the express or implied
warranties on sales of PMI products. Because of the high risks involved in high angle rope work such as, but not limited to, rescue, rope access, caving, rappelling, rock climbing and mountaineering, no further
warranties exist or are implied by PMI. Regulations issued under the Magnuson-Moss Warranty Act require us to include the following statement: some states do not allow limitations on how long an implied
warranty lasts nor the excluding or limitation of incidental or consequential damages, so the above limitations may not apply to you.
WARNING CAUTION
Use this PMI Helmet only if you have been properly trained by an instructor
who is well qualifi ed in all phases of vertical rope work. Good instruction
includes evaluation of the students comprehension of and ability to safely
and effi ciently perform the task(s) being taught.
A
B
C
For additional information about this or other PMI products, contact us.
Pigeon Mountain Industries, Inc.
PO Box 803
LaFayette, GA 30728
Toll Free: 888.764.1437
Phone: 706.764.1437
Fax: 800.952.3747 or 706.764.1531
Email: info@pmirope.com
Web: www.pmirope.com
Equipment Inspection Log
Item: Model #
Size:
Date Use or Maintenance Comments Name
INSTRUCTIONS
Fitting and use:
Place the helmet on your head and turn the knob to adjust the head
band. The fi t should be snug, but not tight. Snap the chin strap under
your chin using the quick disconnect buckle. Adjust the chin strap
by sliding the webbing through the ladder lock side of the quick
disconnect buckle. Excess length of the chin strap can be kept out of
the way with the Velcro fastener. Adjust the nape strap by sliding the
rear webbing though the ladder lock buckle. Always keep the chin
strap fastened while wearing this helmet.
Removal:
To remove the helmet, squeeze both sides of the quick release buckle.
The female side of the buckle should automatically eject from the
buckle.
Strap Retainers:
Use the small bungees at the front and rear of your Ventilator Helmet
to attach a headlamp or the strap of your goggles if desired.
Other Features:
The Ventilator features a built in goggle mount designed for use with
ESS goggles (Product# HL33021 & HL33023), and an optional mount
for ear protection.
Three Point Suspension:
Three points of suspension means that
in addition to the support points on
both sides of the helmet (A/B), a third
point of support is positioned at the
rear (C). The additional point helps to
prevent the helmet from falling forward
over the user’s eyes.
COLORS
Red
HL33068
White
HL33069
SIZING
The PMI Ventilator Helmet is designed to fi t head circumference from
50 to 64cm (20 to 25in).
ADDITIONAL INFORMATION
CAUTION
Always keep the chin strap fastened while this helmet is being worn. An
unfastened chin strap will greatly reduce the ability of this helmet to protect
your head.
WARNING
• YOU COULD BE KILLED OR SERIOUSLY INJURED IF YOU DO NOT READ
AND UNDERSTAND THIS BOOKLET BEFORE USING PRODUCT.
• SPECIAL TRAINING AND KNOWLEDGE ARE REQUIRED TO USE THIS
PRODUCT.
• YOU MUST THOROUGHLY READ AND UNDERSTAND ALL
MANUFACTURERS INSTRUCTIONS BEFORE USE.
• USE AND INSPECT THIS PRODUCT ONLY IN ACCORDANCE WITH THE
MANUFACTURERS INSTRUCTIONS.
• YOU CAN CONTACT THE MANUFACTURER AT 706-764-1437 FOR
IMPORTANT SAFETY INFORMATION.
Altri manuali PMI Accessori per motociclette
