Posi Pin CR-R885-A Manuale utente

PIN and Proximity Reader

For Access Control Systems

(CR-R885-A)

Installation and Operating Instructions

Version 1.0

PosiPin 1

TABLE OF CONTENTS

Installation ............................................................................2

Technical Specifications .......................................................3

Feedback ..............................................................................5

Programming ........................................................................5

Card/Code Options ...............................................................6

Keypad Communication Format ...........................................6

Transfer Limit for 4-bits Buffered Format .............................7

Display on Card Read ..........................................................7

Keypad Lockout ....................................................................8

26-bit Wiegand Card Family Code Setting ...........................8

Reader’s Interface ................................................................9

Check-in Supervision ...........................................................9

Buzzer Setting ....................................................................10

Face Light Intensity ............................................................10

Face Light Operation ..........................................................10

Face Light Colour ...............................................................10

Changing the Installer Code ...............................................11

Panic Alarm ........................................................................11

Resetting to Default ............................................................11

Card Presentation Test ......................................................12

Warranty .............................................................................12

2 Installation and Operating Instructions

INSTALLATION

For PosiPin to function correctly with the access control system,

some programming may be required in the controller or control

panel of the host system. For further instructions, refer to the

appropriate manual. Only explanations directly concerning

PosiPin’s programming will be included in this manual.

Selecting an Installation Site:

• Avoid wiringthe PosiPin cablesin the same conduit asAC power

cables, lock power or signal wiring.

• Reader wiring must remain a minimum of 30cm (12in) away from

other wiring, such as wiring for AC power, computer data,

telephones, electric locks, etc.

• Avoid sites within 1.1m (3.5ft) of computer monitors or CRTs.

• Avoid sites near sources of broad spectrum EMI noise, such as

motors, pumps, generators, DC to AC converters, AC switching

relays, power supplies, and light dimmers.

• Avoid sites near potential sources of RF signals, such as cellular

phones, two-way radios, etc.

Mounting and Wiring

After selecting a site for the PosiPin, use the mounting plate as a

guide to drill two holes to secure the mounting plate and a hole for

the cable 0.95cm to 2.54cm (0.375in to 1in) wide. Place a grommet

around the edge of the hole for the cable. Prepare PosiPin’s cable

by cutting the cable jacket back 3.175cm (1.25in) and stripping the

wires back 0.635cm (0.25in). Splice PosiPin’s wires with a

recommended cable wire. Route the cable to the controller and

connect as shown in Figure 1: Connection drawing on page 4.

PosiPin 3

Mounting on Metal Surfaces

Although the read range may slightly decrease, PosiPin can be

mounted on metal. However, do not box in or surround the card

reader with any kind of metal. If the reader must be installed in a

metal enclosure, ensure that the face of the card reader is not

covered and that at least 1.6" (4cm) remain between the card

reader and the metal on all sides of the card reader.

TECHNICAL SPECIFICATIONS

Input Voltage: Typical: 13.8Vdc, min.: 11.0Vdc, max: 14.5Vdc

Input Current: Typical: 65mA @ 12.5Vdc, with card: 105mA

Consumption: Typical: 812mW @ 12.5Vdc, with card 1.31mW

Frequency: Exciter Field: 125KHz Pulse Modulated, receive low:

12.500KHz, Receive high: 15.625KHz

Operating Temp: -35°C (-31°F) to +65°C (+149°F)

Output formats: Reader: 26- and 37-bit Wiegand

Keypad: 8-, 26- and 37-bit Wiegand, 4-bit with or

without parity, and 4 bits buffered with or without parity

Cable Distance: 152.4m (500ft.)

Suggested Cables: 22AWG, 0.8mm, Multi-conductor, Alpha 5196, 5198

18AWG, 1.2mm, Multi-conductor, Alpha 5386, 5388

Belden 9553, 18AWG, 6-conductor, stranded w/

overall shield

Indicators: Beeper, red LED, green LED, red or green Face Light

Weight: 280g (9.8 oz.)

Material: Black, UV resistant, ABS plastic

Dimensions: 99.5mm (5.75in.) x 118.5mm (2in.) x 19.5mm (1in.)

4 Installation and Operating Instructions

Figure 1: Connection drawing

PosiPin 5

FEEDBACK

Visual Feedback: When information is entered on the reader’s

keypad, the red and/or green LEDs will flash, remain constant or

extinguish depending on the operation.

Confirmation Beep: When an operation is successfully entered,

the reader emits a rapid series of beep tones (“beep-beep-beep-

beep-beep”).

Rejection Beep: When the system reverts to a previous status or

an operation is incorrectly entered, the reader emits one long beep

tone (“beeeeeeeeeep”).

PROGRAMMING

Ensure that corresponding programming is completed in the

control panel or controller connected to the PosiPin. To program:

1. Press and hold the [CLEAR]key for 4 seconds.

The reader emits a confirmation beep and the green LED illuminates.

2. Enter the [INSTALLER CODE]. Press the [ENTER]key.

(default:000000) Reader emits a confirmation beep and the green LED

flashes.

3. Enter the 3-digit [SECTION]. Press the [ENTER]key.

Reader emits a confirmation beep and the green LED stops flashing.

4. Enter the required [DATA]. Press the [ENTER]key.

The reader emits a confirmation beep and the green LED flashes.

5. To program another section, repeat steps 3 and 4. To exit

programming mode, press and hold the [CLEAR]key for 4 sec.

The reader emits a rejection beep and the green LED extinguishes.

6 Installation and Operating Instructions

CARD/CODE OPTIONS

Section [001]

[001][001]

[001] - Default: [3]

[3][3]

[3]

PosiPin can function as a reader, a keypad or as both combined.

KEYPAD COMMUNICATION FORMAT

Section [002]

[002][002]

[002] - Default: [1]

[1][1]

[1]

PosiPin must use the same keypad communication format as the

controller.

Enter Description

[0] Keypad and reader disabled.

For programming only.

[1] Reader only enabled. A user must present a valid

card to the reader for Access Granted.

[2] Keypad only enabled. A user must enter a valid

code on the keypad for Access Granted.

[3] Keypad and reader enabled. A user must present

a valid card and enter a valid code for Access

Granted.

Enter Description

[0] 8-bit Wiegand

[1] 26-bit Wiegand (also see section [006])

[2] 37-bit Wiegand

[3] 4 bits without parity

[4] 4 bits with parity

[5] 4 bits buffered without parity

(also see section [003])

[6] 4 bits buffered with parity (also see section [003])

PosiPin 7

TRANSFER LIMIT FOR 4-BITS BUFFERED FORMAT

Section [003]

[003][003]

[003] - Default: [00]

[00][00]

[00]

This feature sets the number of digits retained in memory before

the data is sent to the controller. For example, if section [003] is set

at05,PosiPinwilltransmitonce5digitsareenteredon thekeypad.

This feature only applies when the format programmed in

Section [002] is set for Option [5]: 4 bits buffered without

parity or Option [6]: 4 bits buffered with parity.

DISPLAY ON CARD READ

Section [004]

[004][004]

[004] - Default: [3]

[3][3]

[3]

PosiPin’s response to a card being presented to the reader can be

adjusted according to the installation’s requirements.

Enter Description

[01] to [11] If section [002] is Option [5]: 4 bits buffered

without parity

[01] to [10] If section [002] is Option [6]: 4 bits buffered with

parity.

Enter Description

[0] Display on Card Read disabled

[1] Red Status LED flashes

[2] Green Status LED flashes

[3] Red and green Status LEDs flash

[4] Face Light flashes

[5] Face Light and red Status LED flash

[6] Face Light and green Status LED flash

[7] Face Light and both Status LEDs flash

8 Installation and Operating Instructions

KEYPAD LOCKOUT

Section [005]

[005][005]

[005] - Default: [0]

[0][0]

[0]

The PosiPin keypad comes with a feature that will lock the keypad

for 60 seconds when an installer code is entered incorrectly 3

consecutive times.

26-BIT WIEGAND CARD FAMILY CODE SETTING

Section [006]

[006][006]

[006] - Default: [000]

[000][000]

[000]

When the keypad is enabled, the card’s family code must be

programmed in order for the keypad to recognize the user’s PIN.

When auser enters a PIN on the keypad, PosiPin will automatically

add the family code programmed in section [006] to the beginning

of the PIN before transmitting the data to the controller. Therefore,

also ensure that all cards to be used with the PosiPin contain the

same family code.

This feature only applies when the communication format

programmed in Section [002] is set for Option [1]: 26-bit

Wiegand.

Enter Description

[0] Keypad Lockout disabled

[1] Keypad Lockout enabled

Enter Description

[0] to [255] Cards’ Family Code

Indice

Altri manuali Posi Pin Lettore di schede

Posi Pin

Posi Pin CR-R885-SB Manuale utente

Manuali Lettore di schede popolari di altre marche

Lindy

Lindy 43185 Manuale utente

Lindy

Lindy 43185 Manuale utente

ViziT

ViziT RD-4F Manuale utente

Jinmuyu Electronics

Jinmuyu Electronics MR811 Series Manuale utente

AVID ID

AVID ID AVID1043 Manuale utente

Conrad

Conrad PCMCIA Manuale utente

Rosslare

Rosslare DR-6255 Manuale utente

Lindy

Lindy 51541 Manuale utente

Diapro T?bbi Ürünler

Diapro T?bbi Ürünler Across System Manuale utente

Johnson Controls

Johnson Controls Kantech tyco ioSmart Manuale utente

ACS

ACS ACR122L Manuale utente

Secukey

Secukey S2-MF Manuale utente

Elecom

Elecom MR-SMC07 series Manuale utente

Alien

Alien ALR-9800 Manuale utente

ACS

ACS ACR310 Manuale utente

Datamars

Datamars R-IN1300 MID Manuale utente

Alarm Lock

Alarm Lock AL-PRE2 Manuale utente

xpr

xpr B100PROX-AH Guida utente