POSIFLEX CD-3200U Manuale utente

Package Contents

CD-3200U/3201U

CD-3200U/3201U 2D image scanner

ST-8000 scanner holder stand (Optional)

USB cable

Quick setup guide for CD-3200U/R

CD-3200R/3201R

CD-3200R/3201R 2D image scanner

ST-8000 scanner holder stand (Optional)

RS-232 cable

Quick setup guide for CD-3200U/R

18160900030 Ver. B0

http://www.posiflex.com

CD-3200U/R & CD-3201U/R

2D Image Scanner

Quick Setup Guide

Product Overview

Front View

Rear View

Scanner Maintenance

The scanner is designed for long-term trouble-free operation and rarely

requires any maintenance. Only an occasional cleaning of the scanner window

is necessary in order to remove dirt and fingerprints.

Wipe the scan window with a soft lint-free cloth and a non-abrasive cleaner to

avoid the scan window from being scratched and damaged. The scan window

can be cleaned while the scanner is running.

The standard interface cable is attached to the scanner with a 10-pin modular

connector. When the connector is properly seated, it is secured in the scanner

by a flexible retention tab. The cable is designed to be field replaceable.

Replacement cables can be obtained from your authorized distributor. To

replace the cable, take the following steps.

1. Make sure the power of both the host terminal and the scanner is powered

off.

2. Disconnect the old scanner cable from the host terminal.

3. Press down the retention tab, and gently pull out the cable.

4. Insert the new interface cable into the bottom of the scanner until it clicks.

Then, plug the new cable into the host.

LED Indication

Status

Explanation

Red LED flashes one time

Power On

Blue LED flashes one time

Good read

Trigger Button

Scan

window

Status LED

Troubleshooting

This section contains information about how to solve problems that you may

encounter when operating the scanner. If a trouble occurs, please refer to the

following diagnostic tips as a mean to solve the trouble. However, before

referring to the tips, make sure that the scanner is installed well. If the problem

remains, contact your dealer.

Problem

Diagnostic Tips

The scanner is on but cannot read

any barcode.

The scanner window is dirty. Clean the scanner

window as described in the Scanner

Maintenance section.

The presented barcode type is not enabled. Use

this guide to tell the scanner to accept that type

of barcode.

The host terminal has disabled the scanner.

Check the setup of host terminal.

The barcode type presented is not supported by

the scanner.

The scanner does not accept more

than two or three barcode labels.

Determine whether the required barcode types

are enabled or not.

A stray barcode is sitting somewhere in the

scanner field of view. Remove all barcode labels

from the scanner’s scan volume and try again.

The scanner cannot send the data to the POS

system. Make sure that the scanner is installed

well and your host POS system is ready to

receive data.

A barcode is read by the scanner

but not accepted by the POS

system.

The communication settings of the system port

and the scanner do not match. Adjust the settings

to make them match to each other.

The scanner is not installed well. Contact your

dealer for the proper installation. The software

running on the POS system does not support the

data format of the barcode label.

When a barcode stays close to the

scanner, the barcode cannot be read

automatically by the scanner.

Check whether or not you have enabled the

Manual Trigger mode. If you have enabled this

mode accidentally, please disable the Manual

Trigger mode by scanning the “Disable trigger”

barcode in the advanced user manual.

Programming Codes

Below are some suggestion you need to bear in mind while scanning labels:

1. The barcode labels shown in bold and black are default factory

settings.

2. Please cover the unwanted codes for scanning the specific barcode

required for the programming to prevent confusion in code scanning.

3. Use the user manual downloaded from our global website or taken from

the Information DVD for advanced programming.

4. Two operational modes, Auto Trigger and Manual Trigger, are provided

to help you manage your daily activities more efficiently via CD-3200

series scanners. By default, both of CD-3200U/R and CD-3201U/R are

set to Manual Trigger.

5. While scanning the setup barcode labels provided in the quick guide, you

need to pull the trigger to initiate the decoding process.

Firmware Version

Scan the below barcode label to retrieve the current firmware version.

Firmware Version

User Interface Switch Barcodes with Defaults Setting

Three types of user interface, including RS-232, USB-HID, and USB

virtual COM, are available for you to select. However, after the interface

type is changed, the current settings will be removed and reset to the default

factory settings. If the scanner fails to switch to the desired interface type,

please either re-plug the I/O cable or restart your host terminal, and then

scan the same barcode label to resolve the problem.

RS232

USB-HID

USB-VCP

Defaults Barcode Setting

To restore the default factory settings, please select one of three barcodes

listed below.

RS232

USB-HID

USB-VCP

Trigger Mode

In general, two trigger modes, Auto Trigger and Manual Trigger, are

offered to help you engage in routine works efficiently using CD-3200

series scanners. While Auto Trigger Mode is activated, the light source of

your scanner will always stay on in order to detect barcode data any time.

On the other hand, with enabled Manual Trigger Mode, the barcode label

will not be decoded unless the trigger button is pulled.

Auto Trigger

Manual Trigger

Auto Trigger Detection Mode

Detection Mode allows you to adjust illumination settings to facilitate the

process of detecting a target code. Through the configurable option, the

status of aiming light can be set to enable or disable. What is more, you

may also arrange the color of illumination in response to the lighting

condition to enhance your scanning performance. However, please be

reminded that Detection Mode only works under the condition that

Trigger mode of CD-3200U/R and CD-3201U/R is set to Auto Trigger.

Regarding each type of available detection modes, the following are related

description for your reference.

Green aiming detection

When a target code falls within the aiming range while the green

aiming light is emitted, the target is detected. It is recommended to

use this mode indoors because the detectability is reduced in an

environment of higher illuminance levels than indoor’s.

Red illumination detection

When a target code falls within the range of the field of view while

the red illumination light is emitted, the target is detected. This mode

can be used in a lighted environment.

No illumination detection

A target code is detected without illumination light. The power

consumption can be reduced, but the response of detection will also

be reduced. Ambient light is used for detection in this mode, so this

cannot be used in a dark place while it can be used in a lighted

environment.

Green aiming detection

Red aiming detection

No illumination detection

Enabling of readable codes

Enable UPC

Enable EAN

Enable Code 39

Enable Codabar

Enable Interleaved 2of5

Enable Chinese Post Matrix 2of5

Enable POSTNET

Enable MSI/Plessey

Enable UK/Plessey

Enable Code 128

Enable GS1-Databar

Enable GS1-Databar Limited

Enable GS1-Databar Expanded

Enable QR Code

Enable PDF417

Setting code specific options

UPC-A, No leading zero, transmit CD

UPC-A, No leading zero, not transmit CD

UPC-A, Leading zero, transmit CD

UPC-A, Leading zero, not transmit CD

Options for UPC-E

UPC-E, No leading digit, transmit CD

UPC-E, No leading digit, not transmit CD

UPC-E, Leading digit, transmit CD

UPC-E, Leading digit, not transmit CD

Options for EAN-13 and EAN-8

EAN-13 not transmit CD

EAN-13 transmit CD

EAN-8 not transmit CD

EAN-8 transmit CD

Disable ISBN translation

Enable ISBN translation

Case conversion

No case conversion

Convert to upper case

Convert to lower case

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali POSIFLEX Lettore di codici a barre

POSIFLEX

POSIFLEX PG-200/2D Manuale utente

POSIFLEX

POSIFLEX PG-200/1D Manuale utente

POSIFLEX

POSIFLEX CD-4860 Foglio di istruzioni

POSIFLEX

POSIFLEX CD-3870 Manuale utente

POSIFLEX

POSIFLEX CD-3830 Manuale del proprietario

POSIFLEX

POSIFLEX CD-3860 Manuale utente

POSIFLEX

POSIFLEX CD-3860 Manuale utente

POSIFLEX

POSIFLEX SK-200 Manuale utente

POSIFLEX

POSIFLEX CD-3860 Manuale utente

POSIFLEX

POSIFLEX LS-1000 Series Manuale utente

Manuali Lettore di codici a barre popolari di altre marche

POSMicro

POSMicro Datalogic PowerScan D7100 Manuale utente

Marson

Marson MT780 Guida rapida alla configurazione

NCR

NCR RealPOS Manuale utente

Motorola

Motorola SE3300 Guida rapida alla configurazione

Element

Element P130BT Manuale utente

Motorola

Motorola Symbol LS3008 Manuale di installazione e funzionamento

Meec tools

Meec tools OBD-II / VAG Manuale utente

SICK

SICK CLP 100 Manuale utente

Royal Tag SA

Royal Tag SA I-Read Manuale utente

Welch Allyn

Welch Allyn IMAGETEAM 3800 Manuale utente

Meteor

Meteor 8310 Manuale utente

Denso

Denso BHT-500B Manuale utente

Datalogic

Datalogic Heron HD3130 Manuale utente

Motorola

Motorola MP6000 Istruzioni di montaggio

Newland

Newland NLS-HR15-BT Manuale utente

ARTDEV

ARTDEV AS-1310 Manuale utente

Aopos

Aopos AS290 Manuale utente

ENS

ENS 367-5455 Manuale utente