Power Electronics Profipower Manuale utente
PROFIPOWER
PROFIBUS - GATEWAY
Communication Network
profibus gateway
modbus – profibus gateway
Communication Network
Edition: June 2007
GBC02CI Rev. C
PROFIPOWER POWER ELECTRONICS
2
POWER ELECTRONICS PROFIPOWER
SAFETY SYMBOLS 3
SAFETY SYMBOLS
Always follow safety instructions to prevent accidents and potential hazards
from occurring.
This symbol means improper operation may results in
serious personal injury or death.
Identifies shock hazards under certain conditions.
Particular attention should be given because dangerous
voltage may be present. Maintenance operation should be
done by qualified personnel.
Edition of June 2007
This publication could present technical imprecision or misprints. The
information here included will be periodically modified and updated, and all
those modifications will be incorporated in later editions.
To consult the most updated information of this product you might access
through our website www.power-electronics.com where the latest version of
this manual can be downloaded.
Revisions
Date Revision Description
16 / 06 /2006 A Software version Profipower 1.0
31 / 10 /2006 B Wiring updating for SD700 and V5
13 / 06 /2007 C Misprints update
PROFIPOWER POWER ELECTRONICS
4
POWER ELECTRONICS PROFIPOWER
INDEX 5
INDEX
SAFETY INSTRUCTIONS..............................................................................7
1. INTRODUCTION ....................................................................................10
1.1. Equipment Description...............................................................10
2. TECHNICAL CHARACTERISTICS ........................................................11
2.1. General Information ...................................................................11
2.2. Dimensions................................................................................12
3. INSTALLATION AND CONNECTION....................................................13
3.1. Installation of Profipower Gateway.............................................13
3.2. Connections of Profipower Gateway..........................................14
3.3. Setting of Profibus Address........................................................23
3.4. Display and Faults Code............................................................24
4. TRIAL RUN ............................................................................................26
4.1. Introduction................................................................................26
4.2. Trial Run with Siemens (Step 7 Set-up).....................................31
4.3. Configuration and Set up ...........................................................33
5. PROGRAMMING FOR STEP 7..............................................................43
5.1. Example of program for Step 7 ..................................................44
5.2. Monitoring and Modification of Modbus Registers......................45
6. DIAGNOSIS............................................................................................46
PROFIPOWER POWER ELECTRONICS
6 INDEX
POWER ELECTRONICS PROFIPOWER
SAFETY INSTRUCTIONS 7
SAFETY INSTRUCTIONS
IMPORTANT!
Safety instructions showed in this manual are useful to teach user
how to use the product in a correct and safety way with the purpose
of preventing possible personal injuries or property damages.
Safety messages included here are classified as it follows:
WARNING
Do not remove the cover while the power is applied or the unit is in
operation.
Otherwise, electric shock could occur.
Do not run the inverter with the front cover removed.
Otherwise, you may get an electric shock due to the high voltage
terminals or exposure of charged capacitors.
Do not remove the cover except for periodic inspections or wiring,
even if the input power is not applied.
Otherwise, you may access the charged circuits and get an electric shock.
Wiring and periodic inspections should be performed at least 10
minutes after the equipment that is going to be connected to this
gateway is disconnected from the input power and after checking
the DC Link voltage is discharged with a meter (below 30VDC).
Otherwise, you may get an electric shock.
Operate the switches with dry hands.
Otherwise, you may get an electric shock.
Do not use cables with damaged insulation.
Otherwise, you may get an electric shock.
Do not subject the cables to the abrasions, excessive stress, heavy
loads or pinching.
Otherwise, you may get an electric shock.
PROFIPOWER POWER ELECTRONICS
CAUTION
Do not allow lint, paper, wood chips, dust, metallic chips or other
foreign matter into the gateway.
Otherwise, fire or accident could occur.
WARNINGS
RECEPTION
Material of Power Electronics is carefully tested and perfectly
packed before leaving the factory.
In the even of transport damage, please ensure that you notify
the transport agency and POWER ELECTRONICS: 902 40 20 70
(International +34 96 136 65 57) or your nearest agent, within
24hrs from receipt of the goods.
UNPACKING
Make sure received merchandise corresponds with delivery note,
models and serial numbers.
Each gateway is supplied with a technical manual.
8 SAFETY INSTRUCTIONS
Indice
Altri manuali Power Electronics Portale
Manuali Portale popolari di altre marche
LST
LST M500RFE-AS Manuale utente
Kinnex
Kinnex Media Gateway Manuale utente
2N Telekomunikace
2N Telekomunikace 2N StarGate Manuale utente
Mitsubishi Heavy Industries
Mitsubishi Heavy Industries Superlink SC-WBGW256 Manuale utente
ZyXEL Communications
ZyXEL Communications ZYWALL2 ET 2WE Manuale utente
Telsey
Telsey CPVA 500 - SIP Manuale utente
