Powernail 50P FLEX Guida all'installazione

50P FLEX

Powernail 50P FLEX Pneumatic Powernailer

POWERNAIL

CO.

OPERATION AND MAINTENANCE MANUAL

MANUAL DE OPERACION Y DE MANTENIMIENTO

MANUEL D’INSTRUCTIONS ET D’ENTRETIEN

Read this manual before you use this Powernailer®. Follow all safety warnings and

instructions. If you are uncertain about the operation of the nailer, call us directly

at 1-800-323-1653 for assistance or contact the closest Powernail Dealer for help.

Please retain this information for future reference.

WARNING

rev. 2019.04.18

REV 3 MASTER

The Powernail 50P FLEX Pneumatic Nailer is designed

to bring Powernail quality to a pneumatic nailer. For

those looking for the ease of use of a pneumatic tool, the

Powernail 50P FLEX is designed for use with only 1" ,

1-1/4", 1-1/2" and 1-3/4" (18 gauge) Powercleats® nails.

The Powernail 50P FLEX is recommended for use on

thinner 3/8", 1/2", 5/8" and 3/4" solid tongue and groove

hardwood as well as some other hard exotics, bamboo,

and engineered woods. For a superior pneumatic Nailer,

look to the company that has been the industry’s quality

leader, POWERNAIL® COMPANY, INC.

INTRODUCTION

INDEX

LIMITED WARRANTY

POWERNAIL® Company, Inc. warrants to its customer, and to the ﬁrst end-use purchaser of

POWERNAIL ﬂooring nailers purchased from an authorized POWERNAIL distributor, that

each serialized manufactured nailer by POWERNAIL®, for a period of 12 months from the

date of purchase, and with respect to the nailer body (speciﬁcally Models 200, 445, and 50P),

for a period of 10 years from date of purchase, (“warranty period”); shall be free of defects in

materials and workmanship and will meet POWERNAIL’s speciﬁcations in effect at the time

of Product shipment. POWERNAIL will repair or replace, at its option, any Powernailer®

that does not conform to this warranty. Claims must be made no later than ﬁfteen (15) days

after the end of the warranty period. POWERNAIL will perform all repair or replacements

itself or through its authorized contractors. POWERNAIL is not responsible for shipping,

labor or other direct or indirect costs. Damage caused by abuse, misuse, unusual or excessive

wear is excluded. Repair or modiﬁcation of the Products by unauthorized parties will void this

warranty. The customer is responsible for returning Products to POWERNAIL for veriﬁcation

of nonconformance. Warranties for Products not manufactured by POWERNAIL are limited to

warranties provided to POWERNAIL by the manufacturer of such product that are assignable

to customer.

THESE WARRANTIES AND REMEDIES ARE EXCLUSIVE OF ALL OTHERS, EXPRESS

OR IMPLIED. THE WARRANTIES OF MERCHANTABILITY AND FITNESS FOR

PURPOSE ARE EXPRESSLY EXCLUDED. IN NO EVENT SHALL POWERNAIL’S

LIABILITY FOR A WARRANTY CLAIM EXCEED THE PRICE PAID TO POWERNAIL

FOR THE NONCONFORMING PRODUCT, REGARDLESS OF THE FORM OR BASIS OF

THE CLAIM OR CAUSE OF ACTION.

Index..................................... 2

Warranty............................... 2

Safety Instructions................ 3

Powernail Company Info...... 3

Operating Instructions.......... 4-9

Top Load Channel................. 5

Parts & Service.................... 6-9

Drive Blade........................... 7

Seal Replacement................. 7-9

Parts List.............................. 10-12

Rear Load Channel and

Original Foot Parts List......... 12

Schematic ........................... 13

Seal Locations Diagram....... 14

Safety Labels........................ 15

Depth Chart.......................... 16

Clear a jam with the R2 foot.. 18

Troubleshooting Chart......... 19

SAFETY INSTRUCTIONS

POWERNAIL COMPANY, INC.

1300 Rose Road, Lake Zurich, IL 60047 US

Phone: 1-800-323-1653 OR 847-847-3000

www.powernail.com

Always use approved SAFETY GLASSES and EAR PROTECTION when operating this Nailer. The

operator and others in the work area should always wear approved FRONT and SIDE eye protection

when operating this Nailer. Eye protection will help guard against ﬂying nails and debris, which could

cause severe eye injury.

EYE AND EAR PROTECTION should be used to prevent hearing damage when there are high noise

levels in the work area.

ALWAYS use ear plugs with a noise reduction rated at 29 db or highter at a construction site.

Nailer noise ratings are at LPA-1sd=90.6,

LWA-1sd=99.3 and LPA-1s,1m=86.3.

Nailer vibration rating: m/s2=3.05.

Always DISCONNECT THE AIR SUPPLY before making any adjustments, repairing, clearing jams or when the

Nailer is not in use. Do not use on scaffolding or ladders and disconnect nailer from air supply when transporting

between installation areas.

Never attach the female end of a quick disconnect to the Nailer. This will trap air inside the Nailer and permit it to

be discharged. Only the unrestricted male connection should be attached to the Nailer.

Nailer requires an air source that can continuously deliver 80 to 110 psi at 3-1/2 cubic feet of air per minute for

operation.

Normal air pressure should not exceed 120 psi or damage to the Nailer and seals may occur. Excess air pressure

can cause the Nailer to explode.

To prevent ﬁre or explosion, use only regulated compressed air—do not use bottled gases of any kind (no oxygen

or combustible gasses) to power this Nailer.

Nailer is intended for use installing wood ﬂooring and is not to be used for purposes not speciﬁed in the operations

manual.

Do not use any nails other than Powernail Powercleats Nails which are speciﬁcally designed for use in any

Powernailer. Powercleats Nails are available in various lengths. Contact your Powernail Dealer for Powercleats

Nails.

Use only Powernail replacement parts in the repair or maintenance of this nailer. Parts or repair services are

available from the manufacturer or from agents authorised by the manufacturer. Repairs should be carried out

only by trained service personel in the ﬁeld of fastener driving tools who will observe proper safety controls while

performing maintenace. Service personel should be qualiﬁed to to asses the safe working condition of fastener

driving tools.

Never place any part of the body in the discharge path of the Nailer when air is connected to the Nailer. Always

make sure Nailer is empty of cleats before connecting air hose so as to prevent any accidental discharge from

occurring.

Never leave the Nailer unattended while it is connected to an air supply.

Whenever air is connected to the Nailer, keep body parts away from the nail discharge path. Disconnect

the air line before making adjustments or repairs on the Nailer. Only connect air to an unloaded Nailer

so as to prevent accidental discharge.

Nailer is activated by striking the plunger. Do not work on scaffolding, ladders, elevated

or uneven surfaces where the nailer could fall and self-activate. Do not leave air

attached to the Nailer when moving from one install location to another.

Figure 2.

Set the nailer on a sample of your ﬂooring.

Raise the nailer foot above the tongue

to line up the nail pocket.

Read these instructions carefully before you use the Nailer.

1. Loosen 2 hex screws.

2. Raise or lower the FLEX to your wood sample.

3. Match the Locating Ear to the nail pocket.

4. Tighten 2 hex screws.

5. Test wood sample with new adjustment.

Hex Allen Wrench

FLEX

Adjustment Lever

Figure 1.

FLEX Tri-Glide Foot Adjustment:

Wood varies from one manufacturer to the next. The

different wood proﬁles may be due to height and

length of the ﬂooring tongue and whether or not there

is a nail pocket.

To use the Powernail 50P Flex, adjust the nailer FLEX foot to a sample of your ﬂooring (see instructions below).

When the nailer foot is adjusted to your ﬂooring, simply place the nailer on the ﬂoor and pull nailer back so the

triangles (Figure 2) catch the edge of the ﬂoor above the tongue. Hit the plunger with the rubber-capped mallet-end

to let the Nailer drive and set the nail at the correct 45 degree angle.

First, loosen the two hex bolts under the FLEX foot with

the Allen Wrench supplied with the nailer. (Figure. 1.)

Next, set the nailer on a sample of your ﬂooring

Use the adjustment lever at the back of the nailer foot to

raise or lower the nailer to the wood.

Match the Adapter Foot Triangles so that it is pointing

into the 90° angle created

by the tongue and the top of the wood (see Figure 2).

For wood with a nail pocket, line up the Triangles at the

top of the nail pocket.

When the adjustment lever is in the correct position

for your wood sample, tighten the two hex bolts to

lock the FLEX foot into place.

Always check your adjustment with a sample to

ensure the nail is driving into the nail pocket.

OPERATION

Adjust so the Triangles

sit slightly above ﬂooring tongue

OPERATION, continued...

Figure 4. Figure 5.

Figure 6.

To Load the Powernail Flex:

Pull back the spring loaded nail pusher towards the end of the channel until the pusher plate locks (Figure 4).

Place up to one stick (100) of Powercleats® (18-gauge) nails, 1" , 1-1/4" , 1-1/2" or 1-3/4" long into the nail

feed slot located on the top of the channel (Figure 5). Release nail pusher from locked position and gently

guide it down until it meets the end of the cleat strip (Figure 6).

To Unload

Pull back the spring loaded nail pusher towards the end of the channel until the pusher plate locks. Then turn

the nailer over so that the nails slide out of the top nail feed slot.

Loading Top Load Channel:

INSERT

CLEATS INTO

TOP FEED

SLOT

GENTLY RELEASE

PUSHER FROM LOCKED

POSITION AND GUIDE

IT TO THE END OF THE

CLEAT STRIP

OPERATION, continued...

WARNING: It is not necessary to hit the Nailer

hard to activate it. Never hit the Nailer with

excessive force or with the metal end of the

mallet, this will damage the Nailer.

Before each use check all screws to be sure

they are tight. Shock and vibration can loosen

screws. Do not over tighten any screw.

AIR SUPPLY:

The air must be clean and dry. Dirty and/or wet

air will damage the Nailer. A combination ﬁlter-

regulator-lubricator is required for proper Nailer

performance and should be placed close to the

Nailer per manufacturer’s recommendations.

The air source must continuously deliver 80 to

110 psi at 3-1/2 cubic feet of air per minute to

operate the Nailer. Connect a clean air hose

and air regulator to the Nailer.

Check for air supply leaks that waste air and

starve the Nailer of air thereby reducing its

performance.

LUBRICATION:

If you do not use an in line lubricator, you must

lubricate the Nailer manually. The frequency

of lubrication is dependent upon the duty cycle

of the Nailer. Continuous duty requires more

frequent oiling than intermittent duty.

At least every eight (8) hours place two to four

drops of Pneumatic Light Air Tool Oil into the

disconnected air line male connector attached

to the Nailer. WARNING: Detergent oil is not

recommended and may damage the seals.

WARNING: Do not over lubricate the Nailer,

excess oil mist or drops will be vented with

spent air when over lubricated. Excess oil could

stain the wood ﬂooring, walls or furnishings. Dry

ﬁre the Nailer, without nails, to purge excess oil,

before you begin to nail down ﬂooring. We will

not be responsible for oil stains. Before storing

the Nailer, lubricate and cycle the Nailer in insure

internal parts are oil protected from corrosion.

PARTS & SERVICE:

When ordering parts include the part number,

part description, Powernailer model and serial

number. Be sure to state the quantity of the

part(s) required. Contact your Powernail Dealer

for the necessary parts or service.

WARNING: Never work on the Nailer if the air line

is attached. Always disconnect the air line from

the Nailer ﬁrst.

NAILER DISASSEMBLY:

TO REPLACE RUBBER BUMPER (#24):

1. Disconnect the air supply

2. Remove the four (4) cap screws holding the

Adapter Foot, Foot and Nail Channel assembly to

the main Body.

3. Pull the Rubber Bumper out of the cylinder

bore. Replace the old Bumper if it shows signs of

wear or it is split.

4. Reverse these steps to reassemble the Nailer.

Be sure to align the Driving Blade with the slot in

the Nail Channel Assembly while you reassemble

the Nailer. NEVER FIRE THE NAILER WITHOUT

THE RUBBER BUMPER INSTALLED, IT WILL

DAMAGE THE NAILER.

For Step-by-Step Videos and Instructions,

Visit our Web Site at: www.Powernail.com

FLEX Foot

Adjustment Video

Service and

Maintenance Videos

TO REPLACE DRIVING BLADE(#15):

1. Disconnect the air supply

2. Remove the four socket head cap screws

holding the Adapter Foot, Foot and Nail Channel

Assembly to the body.

3. Remove the Rubber Bumper

4. Pull the Driving Blade with pliers until the Piston

is fully extended outward towards the bottom of the

cylinder.

5. Use a 15/16” box wrench (Part #: 09-44529768)

to unscrew the Driving Blade Jam Nut and remove

it. Hold the Piston from turning while unscrewing

the Jam Nut by holding the piston hex with a 1-1/8”

box wrench (Part #: 09-44529768).

6. Push out the 1/4" diameter blade retaining

Dowel Pin and remove the broken Driving Blade

stub.

7. Install a new Driving Blade in the slot and

replace the Dowel Pin. Screw on the retaining Jam

Nut using the same tools. If the Jam Nut becomes

worn and loose after frequent removals, it should

be replaced.

8. Check the ﬁt, there should be some sideways

movement between the Driving Blade and the

Jam Nut assembly. This is desirable and helps the

blade to align itself with the mating parts.

9. Reassemble the components. Be sure to align

the Driving Blade with the slot in the Adapter Foot

Assembly, it goes in only one way.

SEAL REPLACEMENT:

There are 7 seals that may require replacement.

We recommend that you have your POWERNAIL

Dealer replace the Seals.

SEAL KIT:

You may choose to buy a Seal Replacement Kit

and replace the seals yourself. It is good practice

to replace all seals at one time regardless if only

one seal needs replacement.

SEAL DESCRIPTION & NUMBER:

1. Piston U cup Lip Seal (#21)

2. Return Cylinder U cup Lip Seal (#17)

3. Piston Rod U cup Lip Seal (#12)

4. Rubber Seat (#18)

5. Plunger Seal Set (#10)

6. Plunger Wiper Seal (#4)

7. Return Cylinder 0 Ring Gasket (#11)

To change Seals follow these procedures.

Be sure the air line is disconnected from the

Nailer ﬁrst before making any repairs. Consult

the illustration for the name and location of the

following component parts.

SEAL REPLACEMENT REQUIRES

REMOVAL OF THE DRIVING BLADE ASSEMBLY:

1. Disconnect the air supply.

2. Remove Rubber Plunger Cap (#7).

3. Unscrew & remove Body Cap (#2).

Unscrew the three 10-32 cap screws holding the

Plunger (#9) to the Return Cylinder (#16).

5. Pull the Plunger up and out of the Nailer Body

(#1) cavity.

6. Remove the Return Cylinder 0 Ring Gasket

(#11) located on the top of the Return Cylinder

under the Plunger.

7. Turn the Nailer over and remove the four foot

screws (#45), that fasten the Adapter Foot and

Nail Channel Assembly to the Nailer Body and lift

the Assembly off the Body.

8. Remove the Rubber Bumper (#24).

9. Pull the Driving Blade Assembly out of the

Nailer Body by pulling on the Driving Blade.

10. Hold the Piston Rod (#13) with an 11/16"

socket over its hex end opposite the Piston.

Do not use pliers or a vise anywhere on the

metal parts, they can damage the sealing

surfaces.

11. Use box wrenches to remove the 5/8-18 Jam Nut

(#22). Remove the Dowel Pin (#14) and Driving

Blade (#15).

OPERATION, continued...

12. Unscrew the Piston from the Piston Rod using box

wrenches and separate the Piston, Piston Rod and

Return Cylinder.

TO REPLACE THE SEALS:

Plunger Seal Set (#10):

1. Remove the Teﬂon®Seal and its O-ring

expander from the Plunger groove using a bent

paper clip or pick. Be sure not to scratch the inside

walls of the seal groove with the wire hook.

2. Clean out the seal groove. Place a new O-ring

into the seal groove by stretching it over the

Plunger body. Make sure the O-ring is not twisted

in the groove. Place a new Teﬂon®Seal Ring into

the seal groove over the O-ring.

3. Carefully push the Teﬂon® Seal Ring over the

edge of the Plunger with your thumbs and into the

groove. Do this as quickly as possible to reduce

stretching of the Teﬂon®Seal Ring. DO NOT

OVER STRETCH THE TEFLON®SEAL RING. Be

sure the Teﬂon®Seal Ring is centered all around

the seal groove and not twisted.

4. Wipe off the Seal surface with a clean rag and

lubricate it generously with Pneumatic Light air tool

oil lubricant.

Rubber Seat (#18):

1. Remove the Cylinder Sleeve (#23). The

Cylinder Sleeve would slide out of the Nailer Body

when you pull out the Driving Blade

2. Remove the metal Support Ring (#19) and

Rubber Seat from inside the Nailer body. NOTE

THAT THE CHAMFER ON THE INSIDE OF

THE RUBBER SEAT FACES THE BOTTOM OF

THE NAILER. Do not reverse the direction of the

chamfer when you replace the Rubber Seat.

3. Replace the Rubber Seat, Support Ring and

Cylinder Sleeve. Be sure to re install the steel

Cylinder Sleeve with the chamfered inside edge

facing the BOTTOM of the Nailer.

Piston U Cup Lip Seal (#21):

1. Remove the old Piston U Cup Lip Seal from the

Piston using a bent paper clip or pick, being

careful not to scratch the inside walls of the

seal groove or the edge of the Piston with the

wire hook.

2. Clean out the seal groove. Place a new

U-Cup Lip Seal into the groove. Make sure the

lip seal is not twisted in the groove and the lips

face the top of the Nailer. See the sketch on

page 12.

3. Carefully wipe off the U Cup Lip Seal surface

with a clean rag and lubricate it generously with

Pneumatic Light air tool oil lubricant.

Return Cylinder U Cup Lip Seal (#17):

1. Use a bent paper clip or pick to remove

the old U Cup Lip Seal from the internal seal

groove inside the Return Cylinder. Be careful

not to scratch the inside walls of the seal

groove with the wire hook.

2. Clean out the seal groove. Place a new

U Cup Lip Seal into the groove, be sure it is

not twisted in the groove. Be sure the lips are

facing the inside of the Return Cylinder as

shown on the Seal Placement sketch on page

12.

3. Carefully wipe off the Lip Seal surface with

a clean rag and lubricate it generously with

Pneumatic Light air tool oil lubricant.

WARNING: The U-Cup Lip Seals #17 and #12

look alike, but they are different, DO NOT mix

them up.

Piston Rod U-Cup Lip Seal (#12):

1. Remove the old U-Cup Lip Seal from the

seal groove with a bent paper clip or pick using

care not to scratch the inside walls of the seal

groove with the wire hook.

2. Clean out the seal groove and install a new

U-Cup Lip Seal. Be sure the Lips are facing the

right direction and are not twisted in the groove.

See the sketch on page 12.

3. Carefully wipe off the Lip Seal surface with

a clean rag and lubricate it generously with

Pneumatic Light air tool oil lubricant.

Plunger Wiper Metal Cap O-Ring (#4):

1. Use a bent paper clip to pick out the Wiper

Seal out of its groove in the Body Cap (#2).

2. Clean out the groove and insert the new

O-Ring (#4) in to the groove in the metal body

cap (#2).

Return Cylinder O-Ring Gasket (#11):

1. Place a new O-Ring Gasket in the groove

on top of the Return Cylinder when you

reassemble the Driving Blade Assembly.

2. Wipe off the O-Ring Gasket seal surface and

lubricate it generously with Pneumatic Light air

tool oil lubricant.

REASSEMBLING THE NAILER:

1. Be sure the Rubber Seat, Support Ring and

Cylinder are installed in the Body and are facing

the correct direction.

2. All seal surfaces must be clean and

lubricated generously with Pneumatic Light air

tool oil lubricant.

Replace any part that shows signs of wear.

3. Use care when installing the seals into their

respective cavities. Be sure the Seals are

contained in their groove and do not come out

as the parts slide together. Generous cavity

lead in chamfers have been provided to help

Seal installation.

4. Carefully insert the Piston Rod into the

Return Cylinder and screw the Piston onto the

rod. Be sure the Piston is facing the correct

way, ears up, hex down.

5. Assemble the Driving Blade, Dowel Pin and

Jam Nut on to the Piston Rod.

6. Insert the Driving Blade Assembly up into the

bottom of the Nailer Body Cylinder.

7. Be sure there is a new O-Ring Gasket in the

top groove of the Return Cylinder.

8. Insert the Plunger into the top cavity of the

Body. Line up the holes and install the three

Plunger retaining screws. It is important that the

three #10-32 screws are tight or air leakage will

occur. Our recommendation is to use 1-2 drops

of blue Loctite® or similar on the 3 screws.

9. Install the Body Cap and Plunger Rubber Cap.

10. Turn the Nailer upside down. Install the

Rubber Bumper, Nail Channel Assembly and

Adapter Foot. Be sure to align up the Driving

Blade with the slot in the Foot before the Nailer is

closed up.

11. NEVER FIRE THE NAILER WITHOUT

THE RUBBER BUMPER INSTALLED, IT WILL

DAMAGE THE NAILER BEYOND REPAIR.

For Step-by-Step Videos and Instructions,

Visit our Web Site at: www.Powernail.com

OPERATION, continued...

For this parts list and other Powernailer schematics, please visit the

Powernail Parts Store at www.powernail.com

POWERNAIL 50P FLEX PARTS LIST

KEY: S=Sold Separately, A= Sold as part of assembly, SEAL=Seal Kit, TU=Tune-up Kit, F=Factory Only

ITEM # PART NO. DESCRIPTION QTY TU SOLD SEPERATE OR

ASSEMBLY / KIT #

1 09-50P3001 BODY 1 F

2 09-50P3150 CAP (LOW PROFILE) 1 S

3 09-50P3202 1/4-20 X 5/8" S.H.C.S. W/ PATCH (COVER) 4 S

4 09-44529729 PLUNGER WIPER METAL CAP O-RING 1 TU S, A-1

5 09-44529759 3/8 NPT 45 DEGREE STREET ELBOW 1 S

6 09-4455418 1/4" AIR FITTING 3/8" NPT 1 S

7 09-44529722 RUBBER CAP 1 TU S

8 09-44529832 #10-32 X 3/4” S.H.C.S. W/PATCH (PLUNGER) 3 S, A-6

9 09-50P3014 PLUNGER (LOW PROFILE) 1 S, A-6

10 09-44529725 PLUNGER SEAL SET 1 TU S, A-1, A-6

11 09-44529731 RETURN CYLINDER O-RING GASKET 1 TU S, A-1, A-6

12 09-2003028 PISTON ROD U-CUP LIP SEAL 1 TU S, A-1, A-6

13 09-50P3010 PISTON ROD 1 S, A-6

14 09-44529740 1/4 X 1/2 DOWEL PIN (DRIVING BLADE) 1 TU S, A-6

15 09-50P3018 DRIVING BLADE 1 TU S, A-6

16 09-2003013 RETURN CYLINDER 1 S, A-6

17 09-2003027 RETURN CYLINDER U-CUP LIP SEAL 1 TU S, A-1, A-6

18 09-44529723 RUBBER SEAT 1 TU S, A-1, A-6

19 09-44529721 SUPPORT RING 1 S

20 09-2003011 PISTON 1 S, A-6

21 09-2003026 PISTON U-CUP LIP SEAL 1 TU S, A-1, A-6

22 09-44529748 5/8-18 JAM NUT (DRIVING BLADE) 1 TU S, A-6

23 09-2003015 CYLINDER SLEEVE 1 S

24 09-44529724 RUBBER BUMPER 1 TU S

25XL 09-50P3201 HANDLE, X-LONG 1 S

25L 09-50P3200 HANDLE, LONG 1 S

26 09-44529744 1/4-20 x 3/4" SHCS W/PATCH 4 S

27L 09-50P3058 NAIL CHANNEL (TOP LOAD), LONG 1 S, A-20

27S 09-50P3056 NAIL CHANNEL (TOP LOAD), SHORT 1 S, A-16

28 09-50P3042R2 GATE (Revision 2) 1 TU S, A-14, A-16, A-20

29 09-50P3017R2 GATE PLATE (Revision 2) 1 TU S, A-14, A-16, A-20

30 09-50P3006R2 STEEL FOOT (Revision 2) 1 S, A-14, A-16, A-20

31 09-44529750 #8-32 X 1-1/2" FHCS (SPACER) 2 S, A-16, A-20

32 09-44529756 1/4 X 1" SPACER (CHANNEL) 2 S, A-16, A-20

33 09-44529751 #8-32 LOCKNUT (SPACER) 2 S, A-16, A-20

34 09-50P3046 1/4-20 x 5/8" SHCS w/patch Torx Drive T27 (R2) 2 S, A-14, A-16, A-20

35 09-50P3047 1/4-28 x 1/2" SHCS w/patch (R2 Gate Plate) 2 TU S, A-14, A-16, A-20

36 09-50P3045 #10-32 x 3/4" FHCS w/patch (R2 Gate) 3 TU S, A-14, A-16, A-20

37 09-50P3050 NAIL PUSHER (TOP LOAD) 1 S, A-9, A-15, A-16, A-20

38 09-50P3054 PUSHER PLATE (TOP LOAD) 1 S, A-15, A-16, A-20

39 09-50P3057 #10-32 x 1-1/2" SHCS (TOP LOAD) 1 S, A-15, A-16, A-20

40 09-44529735.2 NAIL PUSHER KNOB 1 S, A-9, A-15, A-16, A-20

41 09-50P3055 NAIL PUSHER SPRING (TOP LOAD) 1 S, A-9, A-15, A-16, A-20

42 09-445297341 SPOOL (TOP LOAD) 2 S, A-9, A-15, A-16, A-20

Altri manuali per 50P FLEX

Indice

Altri manuali Powernail Pistola sparachiodi

Powernail

Powernail 445 XLL Manuale utente

Powernail

Powernail 45R Manuale utente

Powernail

Powernail 445FS Manuale utente

Powernail

Powernail 2000TN Manuale utente

Powernail

Powernail 445 Manuale utente

Powernail

Powernail PowerTacker Manuale utente

Powernail

Powernail 1890U PowerStapler Manuale utente

Powernail

Powernail 445 XLS Manuale utente

Powernail

Powernail 50P FLEX Manuale utente

Powernail

Powernail 2000 Manuale utente

Powernail

Powernail POWERNAILER 50M FLEX Manuale utente

Powernail

Powernail PowerPalm 02-PALM001 Manuale utente

Powernail

Powernail Powernailer 50M Manuale utente

Powernail

Powernail 445 XLL Manuale utente

Powernail

Powernail BR50 Manuale utente

Powernail

Powernail 445 Manuale utente

Powernail

Powernail PowerStapler 20FS Manuale utente

Powernail

Powernail 15FS Manuale utente

Powernail

Powernail 101R Manuale utente

Powernail

Powernail 445 XLL Manuale utente

Powernail

Powernail 200 Manuale utente

Powernail

Powernail 2000 Pneumatic Powernailer Manuale utente

Powernail

Powernail Powernailer 2000F Manuale utente

Powernail

Powernail 250 Manuale utente

Manuali Pistola sparachiodi popolari di altre marche

Performance Tool

Performance Tool M643 Manuale utente

Hitachi

Hitachi VH650 - Fencing Nailer, Full Head Manuale utente

Parkside

Parkside PET 25 B1 Manuale utente

Senco

Senco Fusion Technology F-35XP Manuale utente

Grizzly

Grizzly G1847 Manuale utente

Ryobi

Ryobi R18N18G Manuale utente

Black & Decker

Black & Decker 492848-00 Manuale utente

HOLZMANN MASCHINEN

HOLZMANN MASCHINEN TN90 Manuale utente

Metabo HPT

Metabo HPT NR 3690DC Manuale di istruzioni

Surtek

Surtek CN650 Dimensioni e guida di installazione

Makita

Makita GF600 Manuale utente

Parkside

Parkside PET 25 B1 Manuale utente

Senco

Senco AirFree 25 Manuale utente

Freeman

Freeman P50LSLW Manuale utente

Aicon PRO

Aicon PRO DAC4507 Manuale utente

DAJ

DAJ XR150A Manuale utente

Makita

Makita AN923 Manuale utente

Grizzly

Grizzly T20644 Manuale utente