PPS RTAP2U Manuale utente
RTAP2U
GNSS Receiver
User Guide
Version 1.1.0
Last Revised September 2, 2021
All materials contained in this document are protected by the copyright law
and may not be reproduced in any form without prior written permission from PP-Solution Inc.
2
Contents
1. Overview ················································································································· 3
1.1 Receiver Overview ····································································································· 3
1.2 Receiver Features ······································································································ 4
2. Receiver Operation ······························································································· 6
2.1 Powering On and Off ······························································································· 6
2.2 Setting Up Connectivity ···························································································· 6
2.3 Receiving RTCM Messages ·················································································· 13
2.4 Checking Performance ···························································································· 16
2.4.1 Positioning Mode ···························································································· 16
2.4.2 Accuracy ··········································································································· 18
2.4.3 Satellite Tracking ···························································································· 19
2.4.4 Map ···················································································································· 22
2.5 Managing Log Files ································································································ 23
2.5.1 STOP and GO logging ················································································· 23
2.5.2 Saving Log Files ···························································································· 24
2.6 Updating Firmware ·································································································· 26
3. Specifications ······································································································· 28
4. Service ·················································································································· 29
4.1 Customer Service ···································································································· 29
4.2 Warranty ····················································································································· 29
3
1. Overview
1.1 Receiver Overview
Thank you for purchasing RTAP2U, a high-precision GNSS receiver. This user guide is
designed to assist users in configuring the receiver and utilizing its features.
RTAP2U is the dual-frequency multi-band GNSS receiver that uses a u-blox ZED-F9P
module. It can receive GPS, GLONASS, BeiDou, Galileo, and QZSS signals. The
receiver supports GPS L1 C/A, L2C, GLONASS L1OF, L2OF, Galileo E1B/C, E5b,
BeiDou B1I, B2I, QZSS L1 C/A, L2C, SBAS L1 C/A signals and can process 184
channels. The device supports RTCM protocol and RTK, VRS, FKP, and PPP-RTK
positioning are available. PPP-RTK positioning based on SSR correction messages can
be enabled through a simple firmware update. With PPP-RTK, more reliable and
accurate navigation is achievable.
RTAP2U delivers centimeter-level accuracy within a few seconds at a data output up
to 20 Hz and provides an accuracy of about 2 centimeters. The device is lightweight
and hand-held size which allows users to carry it and use it for not only surveying but
also drones, autonomous driving, precision agriculture, location monitoring, and more.
The receiver is controllable with a mobile device and a desktop through a user-friendly
web interface “RTAP2U Viewer”. It does not require an app download, and is designed
for both the general public and professionals.
4
1.2 Receiver Features
RTAP2U has an antenna connector for GNSS antennas in the front. The power button
is located on the back side, and UBX1), NMEA2) data are receivable through the USB
port.
GNSS
Antenna
Connector
LED
Power USB
Four LEDs are visible on the top and provide Wi-Fi, Positioning, GPS, and Power
status.
•
Wi-Fi ( )
: Wi-Fi connection
Positioning• ( ): GPS positioning type
GPS• ( ): Satellite signal
Power• ( ): On and off
1) UBX: u-blox module raw data protocol
2) NMEA: National Marine Electronics Association, a standard data format that includes the time, location,
and more from the GNSS device
LED Receiver Status
Wi-Fi
Red: Wi-Fi network connection error
Yellow: Connected to the internal Wi-Fi network but not an external
Wi-Fi network
Green: Connected to the internal and external Wi-Fi network
Positioning
Red: Standalone
Yellow: DGPS
Green blink: RTK-Float
Green solid: RTK-Fix
GPS Green: Receiving satellite signals
Power Green: Power on
5
The physical dimension of RTAP2U is 80.00 × 68.81 × 36.00 mm as described in the
image below.
RTAP2U received the KC certification (Registration of Broadcasting and Communication
Equipments) and the Japan MIC (Requirement for wireless radio communication
devices) certification.
R-R-R2U-RTAP2U
R-C-R2U-RTAP2U-B
6
2. Receiver Operation
2.1 Powering On and Off
Users can turn on RTAP2U by pressing the power button on the back side. The LED
indicator changes by each step as described in the table below. When the device is
completely booted, the Power LED ( ) turns green and the Wi-Fi LED ( ) turns
yellow. It takes about one to two minutes to reboot. You can turn off RTAP2U by
pressing the power button on the back side again.
Step Description
①Rebooting (1~2 minutes)
②Booting complete
2.2 Setting Up Connectivity
RTAP2U has both “AP” mode and “Station” mode. RTAP2U generates and provides
internal Wi-Fi through the AP mode, and users can also connect to the external Wi-Fi
network through the Station mode. With the AP mode, users can access RTAP2U
Viewer and check the accuracy, configure settings, and download data.
RTK and Network RTK positioning is available by receiving RTCM messages. RTAP2U
should be connected to an external Wi-Fi network to receive the messages through the
Internet. The steps below describe how to connect the receiver to an external Wi-Fi
network.
7
Search and connect to the internal Wi-Fi network①
Log in to RTAP2U Viewer②
Establish connection with an external Wi-Fi network③
The following steps (1) through (6) illustrates how to access the RTAP2U Viewer,
connect to the external Wi-Fi network, and receive RTCM messages.
※ This document is based on firmware (v1.1.0_kernel.fw), made in September, 2021.
(1) Connect to the internal Wi-Fi (AP Mode)
<Desktop>
When connecting to the network by a desktop, follow the two steps below. Also note
that the images may differ depending on the user’s PC type, operating system, and
settings.
①R2U-B11-XXXX will appear on the Wi-Fi list.
②Click on it and allow a few seconds to pair.
8
<Mobile Device>
When connecting to the network by a mobile device, follow the three steps below. The
receiver connects to your mobile hotspot for the external network. Also note that the
images may differ depending on the user’s mobile device type, operating system, and
settings.
Set up your mobile hotspot ID and password. The image below is an example.①
Note※
If there is a special character other than “_” included in the SSID, the receiver
may not be able to connect to the hotspot network.
Connection with a 5G network is not available, so please use a 2.4G network.
R2U-B11-XXXX will appear on the mobile Wi-Fi list.②
Tap on it and allow a few seconds to pair.③
9
(2) Open RTAP2U Viewer
Enter 192.168.73.1:5000 on the web browser.
(3) Enter the login information
Type in the below User ID and Password in the RTAP2U Viewer login window.
Then click SIGN IN.
User ID: root•
Password: rtap2u•
(4) Check the connection status with RTAP2U
RTAP2U connection status is visible on the bar at the top left of RTAP2U Viewer.
10
(5) Connect to the external network (Station mode)
The Station mode should be set up through RTAP2U Viewer to connect to an
external network.
①Click Config on the bottom bar and select WI-FI on the top bar.
②Enter the Wi-Fi name (SSID) and password (Security Key), and then click
SUBMIT. The image below is an example.
Note※
Connection with a 5G network is not available, so please use a 2.4G network.
If there is a special character other than “_” included in the SSID, the receiver
may not be able to connect to the external network.
Indice
