PR Lighting LED Studio 3200T Manuale utente

LED Studio 3200T

LED Studio 3200D

This product manual contains important information about the safe installation and use of this

projector. Please read and follow these instructions carefully and keep this manual in a safe place

for future reference.

PR LIGHTING LTD.

http://www.pr-lighting.com

2/14

INDEX

SAFE USAGE OF THE PROJECTOR 3

INSTALLING THE PROJECTOR 4

CONTROL CONNECTION 4

DMX TERMINATOR 5

SETUP OPTIONS-PROJECTOR CONFIGURATION 6

TO SET THE DMX START ADDRESS 6

TIMING SETUP FOR THE PROJECTOR 7

OPERATION MENU 7

DMX PROTOCOL 8

INDICATION OF LED DIGITAL TUBE 9

MAINTENANCE 9

TROUBLESHOOTING 9

TECHNICAL DATA 10

ELECTRICAL DIAGRAM 12

COMPONENT ORDER CODES 13

Please note that as part of our ongoing commitment to continuous product development, specifications are subject to change without

notice. Whilst every care is taken in the preparation of this manual we reserve the right to change specifications in the course of

product improvement. The publishers cannot be held responsible for the accuracy of the information herein, or any consequence

arising from them.

Every unit is tested completely and packed properly by the manufacturer. Please make sure the packing and / or the unit are in good

condition before installation and use. Should there be any damage caused by transportation, consult your dealer and do not use the

unit. Any damage caused by improper use will not be assumed by the manufacturer and / or dealer.

ACCESSORIES

These items are packed together with the projector:

Name Quantity Unit Remark

Barn door 1 Set

Clamp 1 Pc

Safety cord 1 Pc

XLR cable 1 Pc With 5-pin plug

Power cord 1 Pc

This manual 1 Pc

3/14

SAFE USAGE OF THE PROJECTOR

When unpacking and before disposing of the carton, check there is no transportation damage before using the projector.

Should there be any damage caused by transportation, consult your dealer and do not use the apparatus.

The projector can be used indoors and outdoors, IP20.

The projector is not designed or intended to be mounted directly on to inflammable surfaces.

The projector is only intended for installation, operation and maintenance by qualified personnel.

Do not project the beam onto inflammable surfaces, minimum distance is 2m. 2m

Avoid direct exposure to the light from the lamp. The light is harmful to eyes.

Do not attempt to dismantle and/or modify the projector in any way.

Electrical connection must only be carried out by qualified personnel.

Before installation, ensure that the voltage and frequency of power supply match the power requirements of the projector.

It is essential that each projector is correctly earthed and that electrical installation conforms to all relevant standards.

Do not connect this device to any other types of dimmer apparatus.

Make sure that the power-cord is never crimped or damaged by sharp edges. Never let the power-cord come into contact

with other cables. Only handle the power-cord by the plug. Never pull out the plug by tugging the power-cord.

When the projector is hanged to a high place, please use a safety cord provided to pass through the projector handles as

a secondary safety fixing for safety seasons. For details, refer to “INSTALL THE PROJECTOR “section.

Fresnel lens shall be changed if it has become visibly damaged to such an extent than their effectiveness is impaired, for

example by cracks or deep scratches.

Exterior surface temperatures of the projector after 5 minutes’ operation is 45℃, when achieving steady state it is 55℃.

There is no user serviceable parts inside the projector, do not open the housing and never operate the projector with the

covers removed.

Always disconnect from the mains, when the device is not in use or before cleaning it or

before attempting any maintenance work !

If you have any questions, don’t hesitate to consult your dealer or manufacturer.

4/14

INSTALL THE PROJECTOR

The unit was designed to make installation easy: The fixture’s head can be rotated within 240°manually,

before it rotates, two side retainers are loosened with care; after the head at a desired angle, tighten two

side retainers..

Take 1 clamps and 1 safety cord out from the package and mount 1 clamps on the handle of fixture with 1 retainer

attached to the clamp. Hang the fixture on the structure and fasten the screw attached to the clamp. Always ensure

that the projector is firmly anchored to avoid vibration and slipping whilst functioning. Always ensure that the

structure to which you are attaching the projector is secure and strong enough to support the weight of the

fixture. For safety the projector should have a secondary fixing with a safety cord through the handle of the

unit to ensure safe mounting.

Warning:

1. The projector MUST be lifted or carried by the HANDLES instead of clamps.

2. For safety the safety cord should afford 10 times of the unit’s weight.

CONTROL CONNECTION

5/14

Connection between the controller and a projector and between one projector and another must be made with a 2

core-screened cable, with each core having at least a 0.5mm diameter. Please use the projector’s cannon 5- pin signal

input and output cables as connection. The 5-pin signal connections are connected as shown in the figure above.

Note: Care should be taken to ensure that none of the pins touch the metallic body of the plug or each other. The body of

the plug is not connected in any way. The projector accepts digital control signals in protocol DMX512 (1990).

Connect the controller’s output to the first fixture’s input, and connect the first fixture’s output to the second fixture’s input

and connect the rest fixtures in the same way. Eventually connect the last fixture’s output to a DMX terminator as shown

in the figure below.

Not more than five units can be connected to power supply in series. The units can be connected to power supply in

parallel. i the voltage and frequency of the power supply should match those indicated on its nameplate.

DMX TERMINATOR

In the Controller mode, at the last fixture in the chain, the DMX output has to be connected with a DMX terminator. This

prevents electrical noise from disturbing and corrupting the DMX control signals.

The DMX terminator is simply an XLR connector with a 120Ω(ohm) resistor connected across pins 2 and 3, which is

then plugged into the output socket on the last projector in the chain. The connections are illustrated below.

6/14

SETUP OPTIONS-PROJECTOR CONFIGURATION

Projector configuration can be set conveniently via push-button switch and LED display.

Launch the projector and press button ENTER for more than 3 seconds to unlock the panel, the LED will show the

function menu of the projector, each main menu has its submenus and each submenu has a specific function. For

details, please see the “OPERATION MENU” section.

Press button FUNC if you want to browse through the various Setup Options.

Press button ENTER to save your settings or enter the next menu. Press button UP or DOWN to shift.

Press button FUNC, it will return to the main menu or browse through the main menu.

TO SET THE DMX START ADDRESS

Each projector must be given a DMX start address so that the correct projector responds to the correct control signals.

This DMX start address is the channel number from which the projector starts to “listen” to the digital control information

being sent out from the controller. The projector has 1 DMX channel, so set the No. 1 projector’s address 001, No. 2

projector’s address 002, No. 3 projector’s address 003, and so on.

Launch the projector. Press button ENTER for more than 3 seconds to unlock the panel.

Press button FUNC to find “AddR” menu.

Then press ENTER to show DMX address and press UP or DOWN to set DMX address.

At this time, DMX address will flash continuously. Press button ENTER to confirm and it means the setting has been

enabled.

Press button FUNC, it will return to the main menu.

7/14

TIMING SETUP FOR THE PROJECTOR

After the fixture is powered on after FUNC ，DOWN，ENTER buttons pressed together, the first digit of the digital

display is flashing”0” , which means hour counting is cleared and becomes zero and hour counting is ready. After a

fixture is re-powered on , hour counting starts to work.

OPERATION MENU

1st LEVEL 2nd LEVEL 3rd LEVEL 4th LEVEL

AddR

(DMX address)

XXX

（XXX:001~512）

CNFG

(Config settings)

Disp

(Display settings, default

ON)

(

Alwa

s ON

)

(Shut off digital CRT without

pressin

buttons in 3 minutes

)

FACT

(Reset factory setup)

YES

INFO

(Information)

VER

(Software version)

X.X.X

(Display software version)

TEMP XXX

(Display Temperature)

TIME

(Power on hours)

XXXX

(Display power on hours)

(Operation mode)

TEST

(Test mode)

BRVL

(Brightness) V000-255

DMX

(DMX mode)

PRG1

(Preset memory 1）

PRG2

(Preset memory 2）

PRG3

(Preset memory 3）

8/14

DMX PROTOCOL

CHANNEL FUNCTION DMX DESCRIPTION

1 Dimmer 000-255 Dimming from dark to light

9/14

INDICATION OF LED DIGITAL TUBE

Decimal point of the first digital tube On DMX signal OK

Off No DMX signal

The first digital “0” chase mode DMX signal OK

“0” flash mode No DMX signal

Parameters that LED digital tubes

display Flash Parameters not saved, press “ENTER” to save

them

MAINTENANCE

To prolong the life of the projector, it is very important to do the maintenance work. If the projector is idle for a long time,

damp, smoke or particularly dirty surroundings can cause greater accumulation of dirt on its cover and housing. So it

should be cleaned to maintain an optimum light output and at the same time to prevent it from corrupted by acid

gas.

Cleaning frequency depends on the environment in which the fixture operates. Soft cloth and typical glass cleaning

products should be used for cleaning. It is recommended to clean projector at least once every 20 days.

Do not use any organic solvent, e.g. alcohol, to clean housing of the apparatus.

TROUBLESHOOTING

PROBLEM ACTION

The projector doesn’t switch on

¾Power connection is not correct.

¾Power supply is damaged or abnormal. Call a qualified personnel

to fix it.

¾Connection of control board is not correct. Call a qualified

personnel to fix it.

The projector can be turned on, but LEDs do

not emit light and are out of control.

¾Connection of LED board is not correct. Call a qualified

personnel to fix it.

The lamp comes on but the projector

doesn’t respond to the controller

¾Make sure that the projector is correctly configurated.

¾Replace or repair the DMX cable.

The beam appears dim

¾The projector is too hot. Take ventilation measures to make it

cool.

10/14

TECHNICAL DATA

VOLTAGES:

100~240V AC, 50/60Hz

POWER CONSUMPTION:

120W@220V

LED:

Power consumption 200W

Quantity 1pc

Manufacturers Rated LED Life More than 30000 Hours

COLOUR TEMPERATURE:

PR-3200T 3000K

PR-3200D 5000K

DIMMER:

0-100% linearly adjustable

BEAMANGLE:

Spot Light

Field angle(one-tenth-peak) θ29°

Soft light

Field angle(one-tenth-peak) θ97°

CONTROL:

DMX512, 5 pin interfaces

3 preset memories

OTHER FUNCTIONS:

Software version display

fixture usage time display

Disconnect the signal cable, the projector automatically switch off .

HOUSING:

High-intensity die-casting aluminum, IP20

WORK ENVIRONMENT TEMPERATURE:

-20°C~40°C

WEIGHT:

6kg

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali PR Lighting Attrezzatura per DJ

PR Lighting

PR Lighting PILOT 300 Manuale utente

PR Lighting

PR Lighting XLED 3007 Manuale utente

PR Lighting

PR Lighting AQUA LED 1800 FRAMING Manuale utente

PR Lighting

PR Lighting XR480 BWS Manuale utente

PR Lighting

PR Lighting LED Studio 3201D Manuale utente

PR Lighting

PR Lighting XL 1200 Manuale utente

PR Lighting

PR Lighting XR480S BWS Manuale utente

PR Lighting

PR Lighting XR 1700 FRAMING Manuale utente

PR Lighting

PR Lighting PR-2302 Manuale utente

PR Lighting

PR Lighting MEGA 4000 Manuale utente

PR Lighting

PR Lighting JUNIOR JNR PAR ZOOM 3618 Manuale utente

PR Lighting

PR Lighting AQUA 350 BEAM PR-2368 Manuale utente

PR Lighting

PR Lighting XRLED 300 SPOT Manuale utente

PR Lighting

PR Lighting JNR-8119A Manuale utente

PR Lighting

PR Lighting SOLO 575 Manuale utente

PR Lighting

PR Lighting XLED 250 BEAM Manuale utente

PR Lighting

PR Lighting XR 380 Beam Manuale utente

PR Lighting

PR Lighting OMEGA Manuale utente

PR Lighting

PR Lighting XR440 BEAM Manuale utente

PR Lighting

PR Lighting AQUA LED 600 SPOT Manuale utente

PR Lighting

PR Lighting XPar 348 Manuale utente

PR Lighting

PR Lighting CSL 1037 Manuale utente

PR Lighting

PR Lighting MEGA COLOUR 2000 Manuale utente

PR Lighting

PR Lighting XLED 300 Beam Manuale utente

Manuali Attrezzatura per DJ popolari di altre marche

ALPHA LITE

ALPHA LITE ALPHA 1500 Manuale del proprietario

Chauvet

Chauvet OVATION E-930VW Manuale utente

Zumtobel

Zumtobel APHRODITE Home Manuale utente

Snow Masters

Snow Masters Zig Oscillator Manuale utente

EuroLite

EuroLite 50530554 Manuale utente

Beamz

Beamz BUV243 Manuale utente

thomann

thomann Stairville DJ Lase 40-G MK-III Manuale utente

Eagletone

Eagletone 6 Eyes Flower Manuale utente

EuroLite

EuroLite FLD-1508 Manuale utente

Technical Pro

Technical Pro LG8xSEA Manuale utente

JB Systems

JB Systems Lounge Laser DMX Manuale utente

Lightmaxx

Lightmaxx Vega Halo 90 Manuale utente

Elation

Elation FUZE WASH Z350 Manuale utente

Maverick

Maverick MK3 WASH Manuale utente

Infinity

Infinity TF-260C7 Fresnel Manuale utente

Chauvet

Chauvet EVE E-50Z Manuale utente

Eliminator Lighting

Eliminator Lighting E 138 Manuale utente

EuroLite

EuroLite Mini Multicolor LED Flashing Light SC Manuale utente