PR Lighting PR-4500 Manuale utente
TRANSMITTER
PR-4500
This product manual contains important information about the safe installation and use of this
transmitter. Please read and follow these instructions carefully and keep this manual in a safe
place for future reference.
PR LIGHTING LTD.
http://www.pr-lighting.com
2/8
INDEX
SAFE USAGE OF THE DEVICE 3
PRODUCTSTRUCTURE 4
CONTROLCONNECTIONS 4
SETTRANSMITTER’S FUNCTION 5
LED INDICATION 5
EXAMPLE INSTRUCTION 5
MAINTENANCE 5
TECHNICALDATA 6
ELECTRICALDIAGRAM 7
Please note that as part of our ongoing commitment to continuous product development, specifications are subject to change without
notice. Whilst every care is taken in the preparation of this manual we reserve the right to change specifications in the course of product
improvement. The publishers cannot be held responsible for the accuracy of the information herein, or any consequence arising from
them.
Every unit is tested completely and packed properly by the manufacturer. Please make sure the packing and / or the unit are in good
condition before installation and use. Should there be any damage caused by transportation, consult your dealer and do not use the
unit.Any damage caused by improper use will not be assumed by the manufacturer and / or dealer.
ACCESSORIES
These items are packed together with the transmitter:
Name Quantity Unit Remark
External power adapter 1 Pc
This manual 1 Pc
3/8
SAFE USAGE OF THE DEVICE
When unpacking and before disposing of the carton check there is no transportation damage before using the transmitter.
Should there be any damage caused by transportation, consult your dealer and do not use the apparatus.
The transmitter is for indoor use only, IP20. Use only in dry locations. Keep this device away from rain and moisture,
excessive heat, humidity and dust. Do not allow contact with water or any other liquids.
The transmitter is only intended for installation, operation and maintenance by qualified personnel.
Do not attempt to dismantle and/or modify the transmitter in any way.
Electrical connection must only be carried outby qualified personnel.
Before installation, ensure that the voltage and frequency of power supply match the power requirements of the
transmitter.
Make sure that the power-cord is never crimped or damaged by sharp edges. Never let the power-cordcomeintocontact
withothercables.Only handle the power-cord by the plug. Never pull out the plug by tugging the power-cord.
If you have any questions, don’t hesitate to consult your dealer or manufacturer.
4/8
PRODUCT STRUCTURE
Signal wire interface
Power interface
Transmitting antenna
Function button/Indicater LED
CONTROLCONNECTION
Equipment 1
Controller
Signal output Signal input (Lighting or others equipment)
Signal output
Connect the controller’s DMX output to the DMX input of the transmitter. Connect the transmitter’s output to any other
transmitter input or other equipment input.
5/8
SETTRANSMITTER’S FUNCTION
BUTTON OPERATION BUTTON FUNCTION
Do not press Idle/ Normal operation
Momentary (Closure for >100mS-3S) Add receivers
Press button for a long time（Closure for >3S）Unlink all receivers
LED INDICATION
Continuously On DMX present
On 900ms / Off 100ms No DMX present
On 100ms / Off 100ms Linking receivers
On 500ms / Off 500ms Unlinking all linked receivers
EXAMPLE INSTRUCTION
◆Remove paired receiver from transmitter:
1. To remove the pairing of one single wireless receiver from the transmitter: This is easiest to accomplish from the
operation menu of the lighting fixture or by holding the pair/unpaired button on the lighting fixture.
2. To remove the wireless signal from all paired receivers: Press the button on the transmitter for a few seconds until
green LED turns off. When the LED goes out, it shows that all paired devices have been removed.
◆Add wireless receivers to transmitter:
Insure that the receiver to be paired isnot paired with another transmitter. If the receiver is paired with another transmitter,
remove the pairing using the steps 1 or 2 above. Then create a new pairing in accordance with the following description.
1) Pair between transmitter and wireless signal of one light.
Power on the transmitter and the receiver to be paired. Press the button on the transmitter to add receivers. At this time
you will see the green indicator LED on the transmitter begins to flash. The pairing between receiver and transmitter has
been completed when the receivers indicator LED turns on or starts to flash.
2) Pair between transmitter and wirelesssignal of multiple lights.
Power on the transmitter and the receiver to be paired. Press the button on the transmitter to add receivers. At this time
you will see the green indicator LED on the transmitter begins to flash. The pairing between receiver and transmitter has
been completed when the receivers’indicator LED turns on or starts to flash.
MAINTENANCE
Any maintenance work should only be carried out by qualified technicians.
6/8
TECHNICALDATA
POWER ADAPTER INPUT VOLTAGES:
100-240VAC, 50/60Hz
POWER ADAPTER OUTPUT VOLTAGES:
9V DC
POWER CONSUMPTION:
MAX 9W
TRANSMISSION DISTANCE:
700m (Barrier-free)
Maximum number of units on the DMX bus
32
CONTROL MODE:
DMX512, 5-Pin interface
HOUSING:
Composite plastic, IP20
WEIGHT:
0.4kg
SIZES:
197
50
107
GND
SW+
LED+
1
23
4
51
2
3
4
5
DMX-INDMX-OUT
SW
LED
DC JACK
RF
Antenna chassis connector
8/8
PR LIGHTING LTD.
1582 XingyeAvenue,NancunPanyu
Guangzhou, 511442 China
TEL: +86-20-3995 2888
FAX: +86-20-3995 2330
P/N: 320020032
Version: 20110310
Indice
Altri manuali PR Lighting Trasmettitore
