Precor EFX 825 Manuale utente

EFX 885, 835, 825

Service Manual 20039-166

Page 1

EFX 885, 835, 825

Warning: This service manual is for useby Precor trained service providers only.

If you are not a Precor Trained Servicer, you must notattempt to service any Precor Product; Call your dealer for service.

This documentcontains information required to perform the majority of troubleshooting, and replacement procedures

required to repair and maintainthis product.

This document contains general product information, software diagnostic procedures (when available), preventative

maintenance procedures, inspection and adjustment procedures, troubleshooting procedures, replacement procedures

and electrical block and wiringdiagrams.

To move directly toa procedure, click the appropriate procedure in the bookmark section to the left of this page. You

may drag the separator bar betweenthis page and the bookmark section to change thesize of the page being viewed.

EFX 885, 835, 825

Service Manual 20039-166

Page 2

Section One - Things you Should Know

Right, Left, Front,and Back Conventions

In this manual, right, left, front, and back are fromthe perspective of a user standing on the C576ifacing thedisplay

enclosure.

General SystemInformation

The generator performs three functions in the EFX. First, by controlling the amount of electrical load applied to

internal battery. Lastly, one ofthe generators six phase outputwindings is monitored to determinewhen the

unit is in use and when it is idle. This system also determines the stride rate by determining the operating speed

(output frequency) of themonitored generatorwinding.

Warning and Caution Statements and General Safety Guidelines

Warning statements indicate a particularly dangerous activity. Warning statements you will find in this manual include:

If the EFX hasbeen in recent use, the load resistors and load resistor mounting bracket may be extremelyhot.

Because thisis a self powered unit, it will either be necessary to either equip theunit with the optional external

power supply orhave an assistant pedal on the unitwhile voltagemeasurementsare being taken. Because of the

danger of working onthe unit while it is in motion using the optional external power supply is strongly

recommended.

When the unit isused, stairarms are in motion; the generator will operate and produce potentially hazardous

voltages even when the battery is disconnected.

To remove power from the EFX, the optional external power supply (whenequipped) mustbe disconnected

from the wall outlet and the red (positive) lead must be disconnected from the battery. Always ensure that the

EFX external power supply is unplugged from the wall outlet and thered (positive) lead is removed from the

battery when you inspect or adjust theEFX, or whenyou isolate, remove, or replace anEFX component.

Removing the covers exposes high voltage components and potentially dangerousmachinery. Exercise extreme

caution when you perform maintenance procedureswith the cover(s) removed.

During service operations you will bevery close to moving machinery and voltagebearing components. When

you perform maintenance procedures with the covers removed, remove jewelry (especially from earsand neck),

tie up long hair, removeneck ties, and do notwear loose clothing.

Exercise caution when touching any wire or electrical component during EFX operation.

EFX 885, 835, 825

Service Manual 20039-166

Page 3

A pinching hazard exists when the unit is operatedby turning thecrankarms by hand. Itis possible to seriously

pinch a finger between thecrankarm and stairarm. The stairarms should be removed beforeoperating the

crankarms by hand.Caution statements are intended to prevent damage to theEFX as a result ofthe current

activity. Caution statements included in this manual are listed below.

When it is necessary to lift or move the EFX, ensure that the EFX has adequate support and that you useproper

lifting techniques.

Safety guidelines you should know and follow include:

manual and follow all operating instructions.

Operate the EFX on asolid, level surface.Visually check the EFX before beginningservice or maintenance

operations. If it isnot completelyassembled or isdamaged in any way, exercise extreme caution while operating

and checking the EFX.

When operating the EFX, do not wear loose clothing. Do not wear shoes with heels or leather soles.Check the

soles of your shoesand removeany embedded stones. Tie long hairback.

Do not rock the unit. Do not stand or climb on the handlebars, display enclosure, or cover.

Do not set anything on the handlebars, display enclosure, or cover. Never place liquids on any part of the EFX,

while performing service.

To prevent electrical shock, keep all electrical components away from water and other liquids.

Do not use accessory attachments that are notrecommended by themanufacturer-such attachments might

cause injuries.

GeneralInformation

For the latest exploded view, part number and part pricing information, visit the Precor dealer website at

www.precor.com/connection.

Tools Required

Multimeter Allen wrench set

Anti-static kit Screwdriver set

4 - 6 gear puller 7/16 allen key, socket wrench mounted

Precor part number 20030-108 belt gauge Straight edge

US and metric endwrench set

US and metric socket wrench set

Torque wrench, 200 in./lbs.

Torque wrench, 200 ft./lbs

EFX 885, 835, 825

Service Manual 20039-166

Page 4

Section Two Precor Console line

Console Line

The EFX with the upper body exercise andthe adjustable incline system will beavailable with two different console

options, the P80 and the P30. The following sections will provideprocedures on replacing components and

troubleshooting the three consoles. Choose the console section that applies toyour EFX.

EFX 885 with P80 Console

EFX 835 with P30 Console

EFX 825 with P20 Console

EFX 885, 835, 825

Service Manual 20039-166

Page 5

Section Three P80 Console EFX

EFX 885, 835, 825

Service Manual 20039-166

Page 6

Procedure 3.1 P80 Systems Settings

Procedure

1. The Welcome screenwill be the first screen you seewhen you approach the P80 console. Press the Pausekey

and continue holdingit down while youdouble press (prior to 1.1versionsoftwarerelease) or single press (1.1

version or after software release) in sequential order an Xconfiguration on theVolume and Channel key pad (

Channel Up, Volume Down,Volume Up,Channel Down). See Diagram 3.1.1. Release thePause key when

done pressing the arrows. Note: The keypad X configuration sequence should be not faster than 1 second

between each key stroke. Any speed faster than1 second mayresult in an unsuccessful access to thesign-in

screen.

2. The sign-in screen will be displayed. Type in the technician access code and then touch OK. The Settings menu

will be displayed. See Settings Table.

3. Use the System modeto configure settings inways that benefit theusers and the facility. Changes madeto these

settingssave to the fitness equipment. To select a Setting touch on an item in the Settings menu.

Diagram3.1.1

Volume &

Channel Key Pad

Pause Button

EFX 885, 835, 825

Service Manual 20039-166

Page 7

4. Touch BACK to the Welcome screen.

Settings

Menu Item

Description

Navigation

Configure/View/Test

About

System information

settings provide

basic information

including equipment

models and serial

numbers. Most of

these settings are

for informational

purposes only and

cannot be modified.

Touch About

See Procedure 3.2, About

EquipmentUsage

The Equipment

Usage settings

provide information

on individual usage

as well as

cumulative

equipment usage.

This information and

these settings are

accessible only to

administrators and

registered service

technicians.

Touch Equipment

Usage

See Procedure 3.3,

EquipmentUsage

SystemSettings

Use the System

Settings to test your

equipment and set

parameters that

benefit your users

and your facility. The

System Settings

menu is visible only

to administrators

and registered

service technicians.

Touch System

Settings

See Procedure 3.4, System

Settings

Software

Downloads

Allows software to

be automatically

downloaded.

It is recommended

that this remain ON

at all times. Contact

Precor Customer

Service before this

setting is disabled.

Touch Software

Downloads

Touch radio button next to

On to Enable Automatic

Downloads.

DefaultisON

Touch radio button next to

Off to Disable Automatic

Downloads.

Reflashing

Used in advanced

troubleshooting.

Contact Precor

Customer Service

before changing

these settings.

Touch Reflashing

Contact Precor Customer

Service

Available Updates

No Available

Updates(Default)

The default is No

Available Updates.

When Software

Downloads is

enabled and aUSB

flash drive is

installed that

contains a valid

software package,

Available Updates

will be displayed.

Touch Available

Updates

Touch nexttoany of the

available updates.

Touch View to see the

details of the update. Touch

BACK to updates list.

Touch Install toload the

update intothe console.

See Procedure 3.5, Updating

Software.

EFX 885, 835, 825

Service Manual 20039-166

Page 8

Procedure 3.2 P80 About

1. Refer to Procedure 3.1 Settings, to access theAbout menus.

2. About settings providebasic information includingequipment models and serialnumbers. Most of these

settingsare for informational purposesonly and cannot be modified. See About Table. To select a About

item, touch on an item in the About menu.

About

Menu Item

Descriptions

Navigation

Configure/View/Test

EventLog

Provides a list of the most recent

hardware and software events, and

equipment status. If no events have

occurred since the last time the

event log was cleared, the event log

screen will be empty.

Touch Event Log

Details of the Event will belisted.

Touch REFRESH to update the list

in the log.

Touch SAVE to save the log to a

Flash drive device.

Touch BACK to About

EventCount

Number of events recorded by

equipment over its lifetime.

None

Console Serial Number

Set by Precor and stored in the

console's memory.

None

Lower Serial Number

Stored in the console's memory.

Note: This information is not

currently available to be displayed.

None

Location

Entered on console at the time of

registration.

Touch Location

Displays location information.

Touch BACK to About

Release Bundle Version

Shows current version of software.

Automatically updatesas part of

each software upgrade.

Touch Release

Bundle Version

Displays detailed information about

the current software.

Touch BACK to About

Etag Check Interval:

Determines how often the console

will check for updates.

None

HeartbeatInterval

Determines how often the console

communicates with the Server.

None

MinimumHeartbeat

Interval

Minimum amountof time between

heartbeats to the Preva server.

None

MaximumHeartbeat

Interval

Maximum amount of time between

heartbeats to the Preva server.

None

Mfe MAC Address

Stored in the consolesmemory. Set

at factory

None

Network Time Server 1

These addresses are set at the

factory and will notneed to be

changed in the field.

None

Network Time Server 2

These addresses are set at the

factory and cannot be changed in

the field.

None

Network Time Server 3

These addresses are set at the

factory and cannot be changed in

the field.

None

Machine Type

Type of equipment (AMT, RBK,

UBK, EFX, & TRM). Set at factory.

None

3. Touch BACK to Settings. Procedure 3.1.

EFX 885, 835, 825

Service Manual 20039-166

Page 9

Procedure 3.3 P80 Equipment Usage

1. Refer to Procedure 3.1 Settings to access theEquipment Usage menus.

2. The Equipment Usage settings provide information on individual usage as well as cumulative equipment

usage. See EquipmentUsage Table.

3. The Equipment Usagescreen currently does not have additionaldetail or test screens.

4. Touch BACK to Settings. Procedure 3.1.

Equipment Usage

Menu or Information Item

Description

Navigation

DetailorTest

Cumulative Workout Seconds

Total number of seconds. Seconds are countedwhen

the workout clock starts

None

Cumulative Workout Distance

Treadmills will report miles of use.

AMTs will reporta horizontal distance as

miles.

Ellipticals will convert total strides to

miles.

Bikes will convert total revolutions to

miles

None

Cumulative WorkOut Sessions

Total number of sessions. A session is countedif the

summary screen displays.

None

Last Workout StartDate Time

The date of the start of the last workout.

None

Last Workout End Date Time

The date of the end of the last workout.

None

EFX 885, 835, 825

Service Manual 20039-166

Page 10

Procedure 3.4 P80 System Settings

1. Refer to Procedure 3.1 Settings, to access theEquipment Usage menus.

2. Use the System Settings to test your equipmentand set parameters that benefityour users and your facility.

System Settings

Menu or Information Item

Description

Navigation

Configure/View/Test

SystemsTest

The systems tests allow you

to check specific functions of

the equipment.

Touch

Systems

Test

See Procedure 3.6

Connectivity

The connectivity screens

allow you to configure or

provides information about

connection.

Touch

Connectivity

See Procedure 3.7

Display

The display settings allow

you to configure,

Measurement units, Standby

Mode Delay, Time Zone, and

Closed Captioning.

Touch

Display

See Procedure 3.8

TV Settings

TV Settings help you setup

television channels for your

users.

Touch TV

Settings

See Procedure 3.9

Work out Limits

The Workout Limit settings

give you control over how the

equipment is used.Use these

settings to create reasonable

limitations for equipment

usage including speed,

incline, resistance, and

duration.

Touch

Workout

Limits

See Procedure 3.10

Manage Settings

Use this setting to save your

equipment settings to a USB

flash drive, or to import

settings from aUSB flash

drive.

Touch

Manage

Settings

See Procedure 3.11

(Cloning)

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali Precor Ellittica

Precor

Precor Resolute RSL 515 Manuale utente

Precor

Precor Resolute RSL 621 Manuale utente

Precor

Precor Resolute RSL 314 Manuale utente

Precor

Precor Resolute RSL 619 Manuale utente

Precor

Precor EFX 556i Istruzioni per l'installazione e il funzionamento

Precor

Precor Crosstrainer 800 Manuale utente

Precor

Precor AMT Series Manuale utente

Precor

Precor PRECISION SERIES Manuale utente

Precor

Precor Elliptical Fitness Crosstrainer Experience 700... Manuale utente

Precor

Precor 5.17 Manuale utente

Precor

Precor Experience Series Manuale utente

Precor

Precor HANDBOEK EFX 546i Manuale utente

Precor

Precor Resolute RSL 504 Manuale utente

Precor

Precor EFX 815 Manuale utente

Precor

Precor EFX EFX 5.23 Manuale utente

Precor

Precor C534i Manuale utente

Precor

Precor EFX 5.17i Manuale utente

Precor

Precor EFX524 Manuale utente

Precor

Precor C576i Manuale utente

Precor

Precor C532i Manuale utente

Precor

Precor Elliptical Fitness Crosstrainer EFX 5.21 Manuale utente

Precor

Precor Experience EFX 700 SERIES Manuale utente

Precor

Precor HANDBOEK EFX 556i Manuale utente

Precor

Precor EFX 833 Manuale utente

Manuali Ellittica popolari di altre marche

Weslo

Weslo Momentum 4.0 Elliptical Manuale operativo e di manutenzione

Progear Fitness

Progear Fitness Air elliptical pro 1307 Manuale utente

Torque Fitness

Torque Fitness XPLLP Manuale utente

Octane Fitness

Octane Fitness PRO3700C Manuale utente

Xterra

Xterra FS5.8e Manuale utente

Bodyguard

Bodyguard E-40 Manuale utente

Bonn Germany

Bonn Germany Concept 2.2 Manuale utente

NordicTrack

NordicTrack E 9.2 Elliptical Manuale utente

Vision Fitness

Vision Fitness X6600iNetTV Manuale utente

Matrix

Matrix MX-A5x Manuale utente

SportsArt Fitness

SportsArt Fitness ECO-NATURAL Elite E874 Manuale utente

Sears

Sears FREE SPIRIT C249 30737 0 Manuale utente

True

True FS-64 Manuale utente

Sport-thieme

Sport-thieme ST 310 Manuale utente

VIRTUFIT

VIRTUFIT CTR 1.1 Manuale utente

Kettler

Kettler GIRO C 1 Manuale utente

CIRCLE FITNESS

CIRCLE FITNESS E7 Manuale utente

Reebok

Reebok 1000 Zx Elliptical Manuale utente