PRESIDIUM MINI Manuale di istruzioni

I. Disclaimers, Exclusions and Limitations pg. 03

of Liability

II. About this book pg. 04

III. About your Presidium Inside Ring pg. 05

Engraving Machine - Mini

IV. IMPORTANT NOTICE pg. 07

1. GETTING STARTED with your Presidium pg. 08

Inside Ring Engraving Machine - Mini

2. USING your Presidium Inside Ring pg. 10

Engraving Machine - Mini

3. TAKING CARE of your Presidium Inside pg. 11

Ring Engraving Machine - Mini

Contents

(English Version)

I. Disclaimers, Exclusions and Limitations of Liability

PLEASE READ AND NOTE PRESIDIUM WARRANTY

TERMS AND CONDITIONS as stated in the warranty

card. Presidium warranty for its testers are subject to

proper use by its users in accordance with all the terms

and conditions as stated in the relevant user handbook

and shall cover only manufacturing defects.

Due to continuous product improvement, Presidium

reserves the right to revise all documents including the

right to make changes to the handbook without notice and

without obligation to notify any person of such revisions

or changes. Users are advised to check Presidium’s

website from time to time http://www.presidium.com.sg/

Presidium shall not be responsible for any damage or

loss resulting from the use of this tester or handbook.

Under no circumstances shall Presidium, its

manufacturer or any of its subsidiaries, licensors,

distributors, reseller, servant and/or agent be liable for

any direct or indirect damages, resulting from the use of

this tester.

TO THE MAXIMUM EXTENT PERMITTED BY

APPLICABLE LAW, under no circumstances shall

Presidium, its manufacturer or any of its

subsidiaries, licensors, distributors, reseller, servant

and/or agent be responsible for any special,

incidental, consequential or indirect damages

howsoever caused.

The engraver or Presidium Inside Ring Engraving

Machine (PIREM) referred to in this handbook is provided

and/or sold on an “as is” basis. Except as required by

applicable law, no warranties of any kind, either

expressed or implied, including, but not limited to, the

implied warranties of merchantability and tness for a

particular purpose.

II. About this Book

Thank you for purchasing the Presidium Inside Ring

Engraving Machine (“PIREM” or “engraver”).

This handbook is designed to help you set up your

engraver and describes all you need to know about how

to use your engraver accurately and take care of it in

line with its requirements. Please read these instructions

carefully and keep them handy for future reference.

This book also contains the terms and conditions in

relation to the use of the tester including the Disclaimer,

EXCLUSION and Limitation of Liability clauses stated

above in Section I.

III. About your Presidium Inside Ring Engraving

Machine - Mini

The Presidium Inside Ring Engraving Machine - Mini is

a new and improved, even more compact and sturdy

engraving machine, that provides ease of customization

by engraving lettering on inside ring surfaces.

Presidium Inside Ring Engraving Machine - Mini

features the following:

• Wide ring-holding capacity of ring sizes from diameter

Ø13-26mm

• Adjustable letter spacing

• Hardened powder-coated paintwork

• Compact size

Note: Rings of width 2mm and less are not recommended

for engraving.

Product specications:

Description Presidium Inside Ring Engraving

Machine - Mini (mPIREM)

Ring Holding

Capacity

Ring size from approximately

13-26mm

Template Engraving Dial (2-sided)

- Side-1 produces 1mm letters

- Side-2 produces 2mm letters

Letter-spacing

(Pitch)

3-6 teeth movement (2-3mm)

Net Weight 5.5 kg

Gross Weight 6.5 kg

Unit Dimensions 290mm L x 152mm W x 316mm H

Packaging

Dimensions

320mm L x 280mm W x 360mm H

Included in your package:

• One (1) piece Dust Cover

• One (1) piece Engraving Dial (2-sided)

• Five (5) pieces Sample Rings

• User Handbook

• Warranty Card

1 PIREM 1 Lock Nut

2 PIREM 2 Self-centering Jaw

3 PIREM 3 Diamond Cutter

4 PIREM 4 Chucking Knob

5 PIREM 5 Wing Nut

6 PIREM 6 Spacing Adjusting Screw

7 PIREM 7 Pitch Center

8 PIREM 8 Stylus Arm

9 PIREM 9 Tracing Stylus Shaft

10 PIREM 10 Lever

11 PIREM 11 Engaging Lever

12 PIREM 12 Stopper

13 PIREM 13 Engraving Dial

14 PIREM 14 Tightening Knob

IV.IMPORTANT NOTICE

• Do not use, store or expose the engraver in dusty and

dirty areas. Its moving parts can be damaged.

• Do not attempt to open the engraver other than as

instructed in this handbook.

• Do not use harsh chemicals, cleaning solvents, or

strong detergents to clean the engraver.

• Do not paint the engraver. Paint can clog the moving

parts and prevent proper operation.

If the engraver is not working properly, kindly contact

Presidium Customer Service at [email protected].

sg or:

Presidium Instruments Pte Ltd

No. 6 Penjuru Lane

Singapore 609187

Singapore

(65) 6379 5000

Attn: Customer Service Executive

1. GETTING STARTED with your Presidium Inside

Ring Engraving Machine - Mini

To prepare this machine for use, remove all packaging

material and untie the wire that secures the Stylus Arm

(9) to its catch.

Changing the Engraving Dial

Pull and hold the Engaging Lever (12) to disengage the

stopper (13) from the V-groove of the Engraving Dial (14).

Loosen the tightening knob (15) and change to the

reverse side of the Engraving Dial. Retighten the

Tightening Knob (15).

After changing the Engraving Dial (14), release the

Engaging Lever (12) to allow the stopper (13) to engage

the V-groove of the Engraving Dial.

Setting up the Ring Holding

The self-centering chuck is the only workholding device.

Each Self-centering Jaw (2) has a narrow and a wider

groove, to hold narrow and wide rings respectively.

For desired ring holding setup, loosen all three Locknuts

(1) and reverse the three Self-Centering Jaws

according to the diagram below. Secure the ring rmly in

the grooves of the three Self-Centering Jaws by turning

the Chucking Knob (5) clockwise (Fig. 1.1).

Fig. 1.1

Adjusting the Letter Spacing

Letter spacing adjustment is done by loosening the

Wingnut (6) and turning the Adjusting Screw (7). This

adjustment can be set from 3 to 6 teeth movements.

Be sure to tighten the Wingnut in order to lock the

Adjusting Screw together.

For a standard engraving, this machine is set to a

minimum of 3 teeth movements.

Indexing

In order to disengage the Stopper (13) from the V-groove

of the Engraving Dial (14), lift the Lever (11) to its

maximum, till spring resistance is felt, and hold it steady.

Push the Stylus Arm (9) back into its catch and manually

rotate the Engraving Dial (Fig. 1.2).

Fig. 1.2

Slowly release the Lever to activate pitching and to allow

the stopper to engage any of desired template letter.

2. USING your Presidium Inside Ring

Engraving Machine - Mini

The Tracing Stylus Shaft (10) is used to trace the

template letters and the Engraving Diamond (4) to

engrave letters onto the ring surface.

• Pull the Stylus Arm (9) out of its catch.

• With your right hand, depress the Tracing Stylus Shaft

(10) against any desired template letter (Fig. 2.1).

Fig. 2.1

• Push the Lever (11) down with your left hand to allow

the Engraving Diamond to rest against the ring surface.

• With both Tracing Stylus Shaft and Lever depressed,

proceed to engrave letter by letter.

Note: Very light pressure is required to trace with the

stylus. More pressure is required for the lever.

Indice

Manuali Stampante popolari di altre marche

Lexmark

Lexmark 1400 Series Manuale

Canon

Canon i70 Series Manuale utente

Evolis

Evolis Elypso Manuale utente

Kyocera

Kyocera FS-9530DN Manuale utente

Canon

Canon LASER SHOT LBP-1210 Manuale utente

Samsung

Samsung BIXOLON SRP-350plusF Manuale utente

Canon

Canon PIXMA PRO-1 Series Manuale utente

Canon

Canon PIXMA G3560 Guida all'installazione

Dell

Dell Color Laser Printer 2130cn Manuale utente

Tektronix

Tektronix Phaser 840 Manuale utente

Epson

Epson ET-7750 Istruzioni operative

Canon

Canon CLBR 460ps Manuale utente

Eltron

Eltron P210 Guide Manuale utente

Ricoh

Ricoh MD-P1 Manuale utente

Epson

Epson SC-F7100 series Manuale utente

Epson

Epson Stylus C40UX Manuale utente

Canon

Canon imagePASS-A2 Manuale utente

Canon

Canon S820D Manuale utente