Pro Force PWF0102000.03 Manuale utente

PWF0102000.03

Operator Manual

Manuel de L’opérateur

Manual del operador

pro-forceproducts.com 101-3162 3/1/11

DO NOT RETURN TO

STORE!

CALL US FIRST!

CUSTOMER HOTLINE

1-888-895-4549

FOR QUESTIONS OR

SERVICE INFORMATION

STOP

NE PAS RETOURNER AU

MAGASIN!

APPELEZ–NOUS D’ABORD!

ASSISTANCE TELEPHONIQUE

A LA CLIENTELE

1-888-895-4549

POUR L'INFORMATION DE

QUESTIONS OU SERVICE

NO LO DEVUELVA A LA

TIENDA!

¡PRIMERO LLÁMENOS!

LÍNEA DIRECTA DE ATENCIÓN

AL CLIENTE

1-888-895-4549

PARA la INFORMACION de

PREGUNTAS O SERVICIO

ARRÊT

A L T O

IMPORTANT - Please make

certain that everyone who uses

the Pro Force® Pressure Washer

thoroughly reads and under-

stands these instructions prior to

operation.

IMPORTANT - Veiller à ce que

toute personne amenée à utiliser cet

appareil de Pro Force® lise soi-

gneusement ces instructions et les

comprenne avant de procéder à son

utilisation.

IMPORTANTE - Favor de

ceciorarse de que toda persona

que use el Lavador de presión

Pro Force® lea y entienda todas

las instrucciones antes de la

operación.

pro-forceproducts.com

INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19

SERVICIO PARA LOS CLIENTES .............................19

SEGURIDAD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19

Símbolos de seguridad .....................................19

Precauciones generales de seguridad ..........................20

CARACTERÍSTICAS DE SEGURIDAD .........................21

Válvula de descarga de calor ................................21

Dispositivo de seguridad....................................21

Apagado por bajo nivel de aceite ...........................21

Silenciador apagachispas ...................................21

ESPECIFICACIONES ........................................21

SELECCIÓN DE BOQUILLA DE PULVERIZACIÓN .............21

ANTES DE LA OPERACIÓN ..................................22

Preparación incial .........................................22

Ensamblado de manguera y pistola ...........................22

Lubricación del motor......................................22

Combustible .............................................22

CARACTERISTICAS DE MOTOR Y BOMBA ...................22

CONEXIONES DE OPERACIÓN ..............................23

Manguera de alta presión ...................................23

Conexion de agua .........................................23

INSTRUCCIONES DE OPERACIÓN ...........................23

Procedimiento de arranque ..................................23

Encendido del motor.......................................23

INYECCION DE QUIMICOS ..................................23

TÉCNICAS DE LIMPIEZA....................................24

Aplicación de jabón y desgrasador............................24

Aplicación de cera ........................................24

FIN DE LA OPERACIÓN DE LIMPIEZA .......................24

MANTENIMENTO ...........................................24

Conexiones ..............................................24

Boquilla.................................................24

Rejilla de agua ...........................................24

Mantenimiento del motor ...................................24

ALMACENAMIENTO ........................................25

Almacenamiento de la bomba ...............................25

Almacenamiento del motor..................................25

GARANTIA LIMITADA ......................................25

RESOLUCION DE PROBLEMAS ..............................26

LISTA DE PIEZAS Y DIAGRAMA DE PIEZAS ...............28-31

INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11

SERVICE CLIENTELE .......................................11

SÉCURITÉ..................................................11

Symboles utilisés .........................................11

Précautions Générales de Sécurité ............................12

MESURES DE SÉCURITÉ ....................................13

Soupape de surpression thermique ............................13

Loquet de sécurité.........................................13

Arrêt suite au bas niveau d’huile .............................13

Silencieux Pare-étincelles...................................13

SPÉCIFICATIONS ...........................................13

CHOIX DE BUSE DE PULVÉRISATION ........................13

AVANT TOUTE UTILISATION ................................14

Préparation précédant la mise en marche.......................14

Montage du tuyau et du pistolet ..............................14

Lubrification du moteur ....................................14

Carburant................................................14

CARACTERISTIQUES DE MOTEUR ET POMPE ...............14

RACCORDEMENTS .........................................15

Tuyau haute pression ......................................15

Racordement d’eau ........................................15

UTILISATION ...............................................15

Procédure de lancement ....................................15

Mise en marche du moteur ..................................15

UTILISATION DE PRODUITS CHIMIQUES ....................15

TECHNIQUE DE NETTOYAGE ...............................16

Application de Savon ou de Dégraissant .......................16

Application de Cire........................................16

FIN DE L'ACTIVITÉ DE NETTOYAGE ........................16

ENTRETIEN DE L'APPAREIL ................................16

Raccords ................................................16

Ajutage .................................................16

Filtre à eau ..............................................16

Entretien du moteur .......................................16

RANGEMENT ...............................................17

Rangement de la pompe ....................................17

Rangement du moteur......................................17

GARANTIE LIMITÉE ........................................17

DÉPANNAGE................................................18

LISTE DES PIÈCES ET SCHEMA DES PIÈCES ..............28-31

INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3

CUSTOMER SERVICE .......................................3

SAFETY ....................................................3

Safety Symbols ...........................................3

General Safety Precautions..................................4

SAFETY FEATURES .........................................5

Thermal Relief Valve ......................................5

Safety Lock Off Latch .....................................5

Low Oil Shutdown ........................................5

Spark Arresting Muffler ....................................5

SPECIFICATIONS ...........................................5

SPRAY NOZZLE SELECTION.................................5

BEFORE OPERATION .......................................6

Pre-Start preparation.......................................6

Hose and Gun Assembly....................................6

Lubrication ..............................................6

Fuel ....................................................6

ENGINE AND PUMP FEATURES ..............................6

OPERATING CONNECTIONS.................................7

High Pressure Hose........................................7

Water Connection .........................................7

OPERATING INSTRUCTIONS ................................7

Start-up Procedure ........................................7

Starting the Engine ........................................7

CHEMICAL INJECTION .....................................7

CLEANING TECHNIQUES ...................................8

Application of Soap or Degreaser ............................8

Application of Wax........................................8

END OF CLEANING OPERATION.............................8

MAINTENANCE.............................................8

Connections..............................................8

Nozzle ..................................................8

Water Screen .............................................8

Engine Maintenance .......................................8

STORAGE ..................................................9

Pump Storage ............................................9

Engine Storage ...........................................9

WARRANTY ................................................9

TROUBLESHOOTING .......................................10

PARTS LIST AND PARTS DRAWING........................28-31

TABLE OF CONTENTS

TABLE DES MATIÈRES

INDICE

pro-forceproducts.com

English

Congratulations on purchasing a Pro Force®

Pressure Washer. Whether you are doing light

cleaning at home or are needing power to do the

tough jobs, Pro Force® pressure washers are built

to give you the power you need. By following

proper break-in procedures, using recommended

set-up and operating procedures, and performing

preventive maintenance as specified in this manual,

your Pro Force® pressure washer will serve you for

years to come.

Most important is the safety of you and those

around you. Remember that while the Pro Force®

pressure washer gives you the power you need to

complete your job, safety rules should always be

followed.

Thank you for selecting our product.

MAT Industries, LLC

Call our toll free number

1-888-895-4549

8 a.m. to 5 p.m. C.S.T.

or www.pro-forceproducts.com

to obtain warranty service information or

order replacement parts or accessories.

Please have the following information available:

1. Model Number.

2. Serial Number.

3. Date and where purchased.

4. Replacement numbers if you are ordering parts.

MAT Industries, LLC

6700 Wildlife Way

Long Grove, IL 60047

Attention: Warranty Service Department

www. pro-forceproducts.com

Safety Symbols

The following symbols are used throughout this

manual. Follow listed instructions to ensure your

safety.

NOTE: Indicates operation or maintenance

information helpful to improve performance or

operation.

CALIFORNIA PROPOSITION 65 WARNING

This product contains chemicals known to the State

of California to cause cancer, birth defects and/or

reproductive harm.

Indicates an imminently hazardous situation which, if

not avoided, will result in death or serious injury

Indicates a potentially hazardous situation which, if

not avoided, could result in death or serious injury.

Indicates a potentially hazardous situation exists,

which if not avoided, may result in minor or

moderate injury or product damage.

CUSTOMER SERVICE

pro-forceproducts.com

English

The following Safety Precautions apply whenever using,

storing or servicing Pro Force® Pressure Washers or their

engines to reduce the possibility of personal injury.

Overlooking or ignoring these precautions can lead to personal

injury or product damage.

• Readthismanualcarefully.Knowyourequipment.

Consider applications, potential hazards and

limitations for your unit.

 • Knowyourequipment.Considertheapplications,

limitations, and the potential hazards specific to your

unit.

 • Storethepressurewasherinawellventilatedarea

with the fuel tank empty. Fuel should not be stored

near the pressure washer.

 • Neveroperateunderthesesconditions:

a. A noticeable change in engine speed.

b. A noticeable loss of pressure.

c. The engine misfires.

d. Smoke or flames are present.

e. Enclosed compartment.

f. Excessive vibration.

g. Rain or inclement weather.

 • Waterspraymustneverbedirectedtowardsany

electric wiring or directly towards the pressure

washer.

 • Donotallowthehosetocomeincontactwithhot

muffler.

 • Equipmentmustbeplacedonafirm,supporting

surface.

• Removethesparkplugorcablefromthesparkplug

to prevent accidental starting when not in use or

prior to detaching the high pressure hose.

 • Keepthepressurewashercleanandfreeofoil,mud

and other foreign matter.

 • Donotwearlooseclothing,jewelry,oranythingthat

may be caught in the engine.

 • Neverdirectsprayatpeopleorpets.

 • Neverallowchildrentooperatepressurewasherat

any time.

 • Usebothhandstocontrolthewand.

• Donottouchnozzleorwaterspraywhileoperating.

 • Wearsafetygoggleswhileoperating.

 • Onlyapprovedhosesandnozzlesshouldbeused.

 • Thetriggergunmustnotbejammedin“ON”

position during operation.

 • Nevertieknotsorkinkthehighpressurehose.

 • Allhoseconnectionsmustbeproperlysealed.

 • Priortostartingthepressurewasherincoldweather,

be sure ice has not formed in any part of the

equipment.

 • Useonlyrecommendedchemicals.

 • Outdoorsuseonly.

 • Placethepressurewasherawayfromcleaningsite

during operation.

 • Topreventaccidentaldischarge,thespraygunshould

be secured by locking trigger when not in use.

 • Donotrunthepressurewasherformorethanfive

minutes without depressing the trigger or damage to

the pump may result.

 • Checkthefuelsystemperiodicallyforleaksorsigns

of deterioration such as chafed or spongy hose, loose

or missing clamps, or damaged tank or cap. All

defects should be corrected before operation.

 • Donottouchhotmuffler.

 • Service,operateandrefuelunderthefollowing

conditions.

a. Good ventilation.

b. Refuel the pressure washer in a well lighted area.

c. Avoid fuel spills and never refuel while the

pressure washer is running.

d. Avoid an ignition source when refueling.

  e. Useleadfreefuelwithaminimumof85octane.

 • Donotsmokenearthepressurewasher.

 • Donotusedamagedhigh-pressurehoses.

THERMAL RELIEF VALVE

A thermal relief valve is provided to protect the pump

from overheating if the spray gun is closed for an extended

length of time or the nozzle becomes plugged. However, it is

intended to be used as a backup system and every effort

should be made to not permit the pump to heat up.

We recommend turning the pressure washer off if it will

not be used for more than five minutes. This saves wear on

the unit, reduces fuel consumption and extends the life of the

pump by avoiding heat.

SAFETY LOCK OFF LATCH

To prevent accidental discharge of high pressure water,

the safety latch on the trigger should be engaged whenever the

pressure washer is not in use. (Refer to Operating

Instructions.)

LOW-OIL SHUTDOWN

The unit is equipped with a low oil sensor. If the engine

oil level becomes lower than required, the pressure washer

will automatically shut off. (Refer to the engine manual for

this feature.) This protects your pressure washer engine from

operating without proper lubrication.

If the pressure washer engine shuts off and the oil level is

according to specification, check to see if the pressure washer

is sitting at an angle that forces oil to shift. Place on an even

surface to correct this. If the engine fails to start, the oil level

may not be sufficient to deactivate low oil level switch. Be

sure the engine is completely full of oil. See engine manual.

SPARK ARRESTING MUFFLER

THIS PRODUCT MAY NOT BE EQUIPPED WITH A

SPARKARRESTINGMUFFLER.Iftheproductwillbeused

around flammable materials, such as agricultural crops, forests,

brush, grass, or other similar items, then an approved spark

arrester should be installed and is legally required in the State

of California. The California statutes requiring a spark arrester

are Sections 13005(b), 4442 and 4443. Spark Arresters are also

required on some U.S. Forest Service land and may also be

legally required under other statutes and ordinances. For more

information, contact our Customer Service Department at

1-888-895-4549 or www.pro-forceproducts.com.

Maximum Inlet Pressure .................. Upto90PSIG

RPM ......................................3600 RPM

Temperature of Pumped Fluids ................ Upto80°F

Inlet Ports...............................3/4”GHT(F)

Discharge Ports ................................. M22

 Yourpressurewasherhasamaintenance-freepump.

There is no need to change the pump oil.

Consult the factory for special requirements that must be

met if the pump is to operate beyond one or more of the limits

specified above.

Following this information concerning the three nozzles

provided with your pressure washer.

NOTE: The force of the spray on the surface you are

cleaning increases as you move closer to the surface.

15° High Pressure (Yellow): This is the nozzle used for

most cleaning applications. It provides narrow coverage and a

highly powerful water stream.

40° High Pressure (White): This nozzle is used for

cleaning with the widest coverage over a larger area with a

powerful water stream.

65° Low Pressure (Black): Provides low pressure spray

andawidecoverage.Usedprimarilywhenoperatingthe

chemical injector to apply chemicals.

English

pro-forceproducts.com

The pump will overheat and may be damaged, or cause

damage if allowed to circulate more that five minutes.

SAFETY FEATURES

SPRAY NOZZLE SELECTION

SPECIFICATIONS

NOTE: The engine and pump on your Pro Force®

Pressure Washer will often have improved performance

after a break-in period of several hours.

PRE-START PREPARATION

Before starting the pressure washer, check for loose or

missing parts and for any damage which may have occurred

during shipment.

HOSE AND GUN ASSEMBLY

NOTE: Align threaded connections carefully to

prevent damaging threads during assembly. Tighten

connections securely to prevent leaks during operation.

Attach the hose to the inlet of the trigger gun.

LUBRICATION

DO NOT attempt to start the pressure washer engine

without filling the engine crank case with the proper amount

and type of oil. (See the accompanying engine manual for this

information.)Yourpressurewasherenginehasbeenshipped

from the factory without oil in the engine crankcase.

Operating the unit without oil will ruin the engine.

The pump is not equipped with a dipstick or side glass

window. Check oil leaks from the pump. Pump oil is shipped

in the pump from factory.

FUEL

Fill the tank with clean, fresh unleaded automotive

gasoline. (See Figure 1). Regular grade gasoline may be used

provided a high octane rating is obtained (at least 85 pump

octane).

Gasoline is very dangerous. Serious injury may result from

fire caused by gasoline contacting hot surfaces.

Donotoverfillthetank.Keepmaximumfuellevel1/2

inch below the bottom of the filler neck. This will allow

expansion in hot weather and prevent overflow.

pro-forceproducts.com

English

BEFORE OPERATION

ENGINE AND PUMP FEATURES - FIGURE 1

HIGH PRESSURE HOSE

Attach the high pressure hose to the outlet connection

located on the pump. (See Figure 1, page 6).

NOTE: DO NOT use a high pressure hose from

another manufacturer.

WATER CONNECTION

Before connecting to unit, run water through the garden

hose (not supplied) to flush out any foreign matter. Check that

the screen is clean and is in the inlet of the pump. Attach

garden hose to the inlet connection located on the pump. (See

Figure 1, page 6).

NOTE: The water supply must provide a minimum of

4 g.p.m. at 40 to 80 p.s.i. or the pump will be damaged.

START-UP PROCEDURE

1. Ensure water supply is connected and turned on.

2. Release gun safety lock.

3. To allow air to escape from the hose, squeeze trigger on

the gun until there is a steady stream of water coming

from the nozzle.

4. Remove any dirt or foreign matter from the gun outlet and

the male connector of the wand.

5. Insert the nozzle wand into the gun wand and tighten the

twistfast fitting securely by hand.

STARTING THE ENGINE (See Figure 1, page 6)

1. Check oil and fuel level.

2. Adjust choke as necessary.

3. Settheengineswitchtothe“ON”position.

4. Squeeze trigger on pressure washer to release pressure

while pulling on the engine starter rope with a fast steady

pull. Pressure may otherwise build up making starting the

unit difficult.

5. As the engine warms up, open the choke to full.

1. Attach injection tube assembly to the siphon injector on

the pump. (See Figure 1, page 6).

2. Open a container of pressure washer chemical and place

next to the unit near the injection tube.

3. Visually inspect strainer at the end of the injection tube to

verify that it is not clogged.

4. Insert the injection tube into the container all the way to

the bottom.

5. Remove the high-pressure nozzle from the wand

and install the black injection nozzle. The solution will

automatically be mixed with the water and discharged

through the nozzle.

NOTE: For certain models, if the engine throttle is not in

the “fast” position, the injection of the solution

may be decreased or stopped.

If the wand or nozzle is not securely locked into place, it

could be ejected under high pressure when operating the

gun, possibly causing injury or damage.

This pressure washer is intended for use only with

liquid car wash detergents, developed specifically for

pressure washer and with mild soaps. Only use chemicals

compatible with the aluminum and brass parts of the

pressure washer. Powdered soaps may clog the injection

system. Always use chemicals according to manufacturer

directions. MAT Industries, LLC assumes no responsibility

for any damages caused by chemicals injected through this

pressure washer.

OPERATING CONNECTIONS

OPERATING INSTRUCTIONS

CHEMICAL INJECTION

English

pro-forceproducts.com

Cleaning Techniques

When cleaning with the pressure washer, many cleaning

tasks can be solved with water alone, but for most tasks it is

advantageous to use a detergent also. A detergent ensures a

quick soaking of the dirt allowing the high pressure water to

penetrate and remove the dirt more effectively.

Pressure washer chemicals are specially formulated to be

used with your pressure washer.

APPLICATION OF SOAP OR DEGREASER

1. ApplythesolutiontoaDRYworksurface.

On a vertical surface, apply horizontally from side to side

starting from the bottom to avoid streaking.

NOTE: Wetting the surface first is not recommended,

as it dilutes the detergent and reduces its cleaning

ability. Avoid working on hot surfaces or in direct

sunlight to minimize the chances of the chemical

damaging painted surfaces. Damage may occur to

painted surface if chemical is allowed to dry on the

surface. Hold nozzle far enough away from surface to

prevent damage to the surface.

2. Allow chemical to remain on the surface for a short time

before rinsing.

3. Rinse with clean water under high pressure. On a vertical

surface, first rinse from the bottom up, then rinse from the

top down. Hold nozzle 6 to 8 inches from the work sur

 faceata45°angleusingtheflatsprayasapeelingtool 

rather than a scrub brush.

APPLICATION OF WAX

1. Immediately after cleaning, apply pressure washer wax.

Place injection tube in container of wax.

2. Apply the wax sparingly in an even layer. Apply to wet

surfaces from the bottom up for even distribution and to

avoid streaking.

3. Remove the suction tube from the wax bottle and rinse off

the surplus wax.

NOTE: IF SURPLUS WAX IS NOT REMOVED, A

HAZY FINISH MAY RESULT.

4. Wipe dry to reduce water spotting.

End of Cleaning Operation

When you have completed use of the chemical injection

system, remove tube from container. Continue to run in low

pressure position and inject clean water through the tube and

injection system by placing end of tube in a container of clean

water. Continue to run until it is thoroughly cleaned.

CONNECTIONS

Connections on pressure washer hoses, gun and spray

wand should be cleaned regularly and lubricated with silicon

grease to prevent leakage and damage to the o-rings.

NOZZLE

Clogging of the nozzle causes the pump pressure to be too

high and cleaning is immediately required.

1. Remove the nozzle from the wand.

2. Clear the nozzle with the nozzle cleaner pin provided with

the pressure washer.

3. Flush the nozzle backwards with water.

4. Re-install the nozzle into the wand.

Restart the pressure washer and depress the trigger on the

spray gun. If the nozzle is still plugged or partially plugged,

repeat above items 1-4.

If the previous procedure does not clear the nozzle,

replace with a new nozzle.

WATER SCREEN

The pressure washer is equipped with a water inlet screen

to protect the pump. If the screen is not kept clean, it will

restrict the flow of water to the pressure washer and may

cause damage to the pump. Do not damage the screen while

removing or cleaning screen. Any foreign particles entering

the pump may damage the pump. Do not operate pressure

washer without the screen in place.

Remove the screen and back flush to remove impurities

from screen. Replace immediately.

ENGINE MAINTENANCE

During the winter months, rare atmospheric conditions

may develop which will cause an icing condition in the

carburetor. If this develops, the engine may run rough, lose

power, and may stall.

NOTE: Refer to the engine manufacturer’s manual

for service and maintenance of the engine.

A nozzle cleaner must only be used when the spray nozzle

is disconnected from the gun or personal injury could result.

CLEANING TECHNIQUES MAINTENANCE

END OF CLEANING OPERATION

pro-forceproducts.com8

English

PUMP STORAGE

If you must store your pressure washer in a location where the

temperatureisbelow32°F,youcanminimizethechanceofdamage

to your machine by utilizing the following procedure:

1. Shut off water supply and relieve pressure in the spray gun

by depressing the trigger. Disconnect the garden hose

from the pressure washer, but leave the high-pressure hose

connected.

2. Tip the unit on its side with the inlet connection pointing up.

3. Insert a small funnel (to prevent spilling) into the inlet

and pour in approximately 1/4 cup of RV antifreeze.

4. Disconnect spark plug wire.

5. Without connecting garden hose pull the recoil several

times to circulate the antifreeze in the pump system.

Continue to add antifreeze and pull the recoil until the

antifreeze is expelled when the trigger is pulled.

6. Turn the unit upright.

Another method of reducing risks of freeze damage is to drain

your pressure washer as follow:

1. Stop the pressure washer and detach supply hose and high

pressure hose. Squeeze the trigger of the discharge gun to

drain all water from the wand and hose.

2. Restart the pressure washer and let it run briefly (about 5

seconds) until water no longer discharges from the high

pressure outlet.

ENGINE STORAGE

When the pressure washer is not being operated or is being

stored more than one month, follow these instructions:

1. Replenish engine oil to upper level.

2. Drain gasoline from fuel tank, fuel line, fuel valve and

carburetor.

3. Pour about one teaspoon of engine oil through the spark

plug hole, pull the recoil starter several times and replace

the plug. Then pull the starter slowly until you feel

increased pressure which indicates the piston is on its

compression stroke and leave it in that position. This

closes both the intake and exhaust valves to prevent the

inside of the cylinder from rusting.

4. Cover the pressure washer and store in a clean, dry place

that is well ventilated away from open flame or sparks.

NOTE: We recommend always using a fuel stabilizer. A fuel

stabilizer will minimize the formulation of fuel gum deposits

during storage. The fuel stabilizer can be added to the gasoline

in the fuel tank, or into the gasoline in a storage container.

Warranty Coverage: MAT Industries, LLC (the Company)

warrants to the original retail customer in North America that it will

repair or replace, free of charge, any parts found by the Company or

its authorized service representative to be defective in material or

workmanship. This warranty covers the cost of replacement parts

and labor for defects in material or workmanship.

Not Covered:

·Transportation charges for sending the product to the Company

or its authorized service representative for warranty service, or

for shipping repaired or replacement products back to the

customer; these charges must be borne by the customer.

·Engine may be covered exclusively by a separate warranty from

the engine manufacturer as set forth in the engine Manual (if

included).

·Damages caused by abuse or accident, and the effects of

corrosion, erosion and normal wear and tear.

·Warranty is void if the customer fails to maintain and operate

the product as instructed and recommended by the Company in

the owner's manual.

·Warranty applies only if the product is used solely for consumer

applications, and does not apply if the product is used for

commercial or business applications, or as rental equipment.

·The Company will not pay for repairs or adjustments to the

product, or for any costs or labor, performed without the

Company's prior authorization.

Warranty Period: One (1) year from the date of purchase. For

warranty service, the customer must provide dated proof of purchase

and must notify the Company within the warranty period.

For warranty service: Call toll free 1-888-895-4549, or write to

MAT Industries, LLC, 6700 Wildlife Way, Long Grove, IL 60047.

EXCLUSIONS AND LIMITATIONS:THECOMPANYMAKES

NOOTHERWARRANTYOFANYKIND,EXPRESSOR

IMPLIED.IMPLIEDWARRANTIES,INCLUDING

WARRANTIESOFMERCHANTABILITYANDOFFITNESSFOR

APARTICULARPURPOSE,AREHEREBYDISCLAIMED.THE

WARRANTYSERVICEDESCRIBEDABOVEISTHE

EXCLUSIVEREMEDYUNDERTHISWARRANTY;LIABILITY

FORINCIDENTALANDCONSEQUENTIALDAMAGESIS

EXCLUDEDTOTHEEXTENTPERMITTEDBYLAW.

This warranty gives you specific legal rights, and you may also have

other rights which vary from state to state. Some states do not allow

a disclaimer of implied warranties, or the exclusion or limitation of

incidental and consequential damages, so the above disclaimers and

exclusions may not apply to you.

Prior to restarting, thaw out any possible ice from the

pressure washer hoses, spray gun and wand.

STORAGE LIMITED WARRANTY

English

pro-forceproducts.com

PROBLEM

Engine will not start or stops while

operating.

Engine is overloaded.

Water or oil leaking from bottom of pump.

Pressure increases when gun is closed.

Engine running but pump not building

maximum pressure or has irregular

pressure.

No intake of chemicals

Trigger will not move.

Water in crankcase.

Noisy operation.

Rough/pulsating operation with pressure

drop.

High crankcase temperatures.

POSSIBLECAUSE

Low-oil shutdown.

Engineswitchnotinthe“ON”position.

Pressure build up in hose.

Nozzle partially blocked.

Excessive pressure.

A small amount of leakage is normal.

Bypass valve not operating properly.

Faucet closed

Unithasbeenstoredinfreezing

temperatures.

Inadequate water supply.

Water inlet screen clogged.

Kinkingardenhose.

Wand nozzle worn or damaged.

Air in pump.

Suction or discharge valves clogged or

worn out.

By-pass valve not operating effectively.

Injection tube not securely inserted into

unit.

Tube cracked or split.

Wrong nozzle.

Injection tube strainer clogged.

Nozzle blocked.

Dried chemicals in injector.

Gun safety lock engaged.

High humidity.

Worn seals.

Worn bearings

Air mixed with water.

Worn packing.

Inlet restriction.

Unloader.

Air mixed in water.

Wrong grade of oil.

Improper amount of oil in crankcase.

CORRECTION

Fill engine with oil.

Turnswitch“ON”.

Squeeze trigger.

Clean nozzle.

Reduce pressure by using pressure

adjustment knob

If excessive leaking occurs call the

Customer Service Department.

Call the Customer Service Department.

Open faucet.

Thaw out unit completely including hose,

gun and wand.

Provide a minimum of 4 gpm at 20 psi.

Clean screen.

Straighten hose

Replace nozzle,

Let run with gun open and wand removed

until steady stream of water is released.

Call the Customer Service Department.

Push firmly into injector.

Replace tubing.

Switch to low pressure nozzle.

Clean strainer.

Clean nozzle.

Dissolve by running warm water trough the

injection tube.

Release safety lock.

Change oil more frequently.

Call the Customer Service Department.

Check inlet lines for restrictions and /or

proper sizing.

Call the Customer Service Department.

Check system for stoppage, air leaks,

correctly sized inlet plumbing to pump.

Check unloader for proper operation.

Check inlet lines for restrictions and/or

proper sizing.

Userecommendedoil.

Adjust oil level to proper amount.

pro-forceproducts.com10

English

Altri manuali per PWF0102000.03

Indice

Lingue:

Altri manuali Pro Force Idropulitrice

Pro Force

Pro Force PWF0102000.03 Manuale utente

Manuali Idropulitrice popolari di altre marche

Shark

Shark RG-232637 Manuale utente

Shakti Technology

Shakti Technology S3 Manuale utente

Kärcher

Kärcher K 4 Pure Manuale utente

Porter-Cable

Porter-Cable D25806-025-2 Manuale utente

REM POWER

REM POWER HDEm 662 Manuale utente

Landa

Landa HS-3000 Manuale utente

Craftsman

Craftsman 580.752270 Manuale utente

HIKOKI

HIKOKI AW 100 Manuale utente

Delco

Delco DC 1302 Manuale utente

Kärcher

Kärcher K 3 Full Control Manuale utente

BIEMMEDUE

BIEMMEDUE 120/10 - 170/13 Manuale utente

ARKSEN

ARKSEN 014-HG-14141-HR Manuale utente

Black & Decker

Black & Decker PW1700SPX Manuale utente

Kärcher

Kärcher 595 - SPARE Guida

Kranzle

Kranzle B 10 200 Manuale utente

Stihl

Stihl RE 90 Manuale utente

Husky

Husky HU80911 Manuale utente

PowR-Quip

PowR-Quip PQ-2600 Manuale utente