Pro-Lift F1500A Manuale utente

OWNER’S MANUAL

WORKING LOAD LIMIT 1500KG

• Safety Instructions

• Operation Procedures

• Maintenance Procedures

READ RULES FOR SAFE OPERATION

AND INSTRUCTIONS CAREFULLY

Model: F1500A

THIS JACK CONFORMS TO MANDATORY

STANDARD AS 2615:2016

Shinn Fu (Australia) PTY. LTD.

15 Viewtech Place, Rowville, Victoria 3178, Australia

FLOOR JACK

WARNING: THE JACK MUST BE USED ONLY ON HARD LEVEL

SURFACES AND BE FREE TO ROLL DURING LIFTING AND LOW-

ERING. DO NOT GET UNDER A VEHICLE THAT IS SUPPORTED

BY A TROLLEY JACK - USE THIS HYDRAULIC TROLLEY JACK

WITH SUITABLY RATED VEHICLE SUPPORT STANDS.

SAFETY INSTRUCTIONS

INSPECTIONS

This hydraulic trolley jack is designed to be used with a 48mm diameter head cap.

1. BEFORE EACH USE

Visual inspection should be made before each use of the trolley jack for abnormal

conditions such as cracked welds, leaks and damaged, loose, or missing parts.

2. AFTER EACH USE

Trolley jack should be inspected immediately if the lift is believed to have been

subjected to an abnormal load or shock. It is recommended that inspection be made

by manufacturer’s or supplier’s authorised repair facility.

3. ANNUAL INSPECTION

Annual inspection of the trolley jack is recommended and is recommended to be

made by the manufacturer’s or supplier’s authorised repair facility to ensure that

your trolley jack is in optimum condition.

RECOMMENDATION FOR SAFE USAGE OF THE JACK

1. Consult the vehicle manufacturer’s manual prior to the lifting of the vehicle.

2. Conduct a pre-operational check of the equipment.

3. Use the hydraulic trolley jack for lifting and lowering only; the raised vehicle should

be supported on suitably rated vehicle support stands.

4. Use the hydraulic trolley jack on a hard level surface and ensure it is free to roll

during lifting and lowering.

5. No person should remain in a vehicle that is being lifted.

6. Chock the unlifted wheels of the vehicle.

7. Centrally locate the load on the head cap.

8. Support the vehicle on suitably rated vehicle support stands and remove the hydraulic

trolley jack prior to commencement of work on the vehicle.

9. No person should get bodily under a vehicle that is supported only by a hydraulic

trolley jack.

10. Make sure that lift point is stable and properly centered on jack saddle.

11. Vehicle should be clear of all passengers. Transmission should be in gear (or park

for automation transmission) and the emergency brake should be engaged.

12. Familiarize yourself thoroughly with this owner manual before operation to prevent

damage to jack and property, or personal injury.

Modications: Modications must not be carried out or accessories added.

SAFETY INSTRUCTIONS

CAUTION BEFORE USE

Due to shipment and/or handling air can be trapped in the hydraulic system, which can

interfere with the jacks lifting. To release air from the hydraulic system:

• Open release valve by turning the jack handle counterclockwise.

• Remove the oil ller plug from the cylinder.

• Rapidly pump jack handle through several full strokes.

• Replace the oil ller plug into the cylinder.

WARNING

DEATH OR

INJURY FROM

INCORRECT USE

USE TWO

SUPPORT

STANDS

FLAT HARD

LEVEL GROUND

FREE TO ROLL

DURING LIFTING

AND LOWERING

REFER TO VEHICLE MANUFACTURER’S

MANUAL FOR INSTRUCTIONS

OPERATION PROCEDURES

Before using

1. Remove cover plate (friction t, easily

removes) and open Oil Filler Plug to

allow air to be vented.

2. Open Release Valve with the handle.

Turn it counterclockwise.

3. Pump handle rapidly several times.

4. Close oil ller plug, then replace cover

plate.

5. No person should remain in the vehicle

that is being jacked.

Raising the jack

1. Place car in park, apply emergency

brake and chocked wheel in “straight

ahead” position.

2.Close Release Valve TIGHTLY (by

applying handle turning clockwise).

3. Position jack under load so that saddle

will contact load rmly and is centered

so it cannot slip. Avoid off-centered load

on the saddle.

4. Operate jack handle until saddle almost

approaches to contact with load. Once

again check to see that the saddle is

correctly positioned.

5. Raise load to desired height. Transfer

the load to Jack Stands immediately.

Lowering the jack

Open Release Valve VERY SLOWLY (by

applying handle turning counterclockwise)

and never more than 1/2 turns. When

Release Valve is opened, saddle will lower

easily due to spring tension on the Lift Arm

Assembly.

Moving the jack

Place handle in Handle Sleeve. DO NOT

move the jack when handle is on the

Release Valve as this may cause damage

to the pump unit of the jack. DO NOT move

the jack when it is under load.

CAUTION

Keep clear from the vehicle when

lowering the jack.

PARTS KEY

1. Oil Filler Plug

(Not shown, under Cover Plate)

2. Castor

3. Base

4. Release Valve

5. Pump Cylinder

6. Pump Piston

7. Handle Sleeve

8. Cover Plate

9. Lifting Arm

10. Saddle

11. Link Rod

12. Front Wheel

13. Frame

14. Middle Spindle

15. Reservoir

(Not shown, under Cover Plate)

16. Handle

17. Carrying Handle

815

MAINTENANCE PROCEDURES

MAINTAINING OIL LEVEL

Important Note:

When adding or replacing oil, always

use a good grade Hydraulic Jack Oil (or

transmission oil, turbine oil etc.). Avoid

mixing types of oil. DO NOT use Brake

Fluid, Alcohol, Glycerine, Detergent, Motor

Oil or Dirty Oil. Improper uid can cause

serious internal damage to Jack.

ADDING OIL:

With saddle fully lowered & jack on level

ground, remove cover plate then open

Oil Filler Plug. Oil level should be approx.

12mm below valve hole. If low, add oil

as needed then close Oil Filler Plug and

replace cover plate.

REPLACING OIL:

For better performance and longevity,

replace oil supply once a year. To drain

oil, remove cover plate, open Oil Filler

Plug and loosen the Release Valve by

applying handle turning counterclockwise.

BE VERY CAREFUL not to permit dirt or

foreign matter to get into the system. Close

Oil Filler Plug and replace cover plate.

SPECIFICATIONS

Working Load Limit : ......................................................................................... 1500Kg

Jack Dimension : ...............................................................445mm x 202mm x 135mm

Height Lowered : ...............................................................................................135mm

Height Raised : ..................................................................................................330mm

Oil Capacity : ...................................................................................................70+/-5cc

Net Weight : .........................................................................................8.4Kg. (approx.)

202mm

445mm

65mm40mm

330mm

135mm

130mm

TROUBLESHOOTING

(USING JACK WITHIN RATED LOAD CAPACITY)

POSSIBLE JACK PROBLEMS

POSSIBLE CAUSES AND

SOLUTIONS

(Refer to Operation and

Maintenance procedures

for detailed information)

Release valve not tightly

closed.

To close or tighten, turn

release valve clockwise.

Air is in hydraulic system.

Release air from system.

Oil level is low in jack

Add oil as required

1. Oil reservoir is over-lled

Drain out some oil.

2. Lubrication of moving

parts is necessary.

Power unit is

malfunctioning.

Replace the power unit.

Jack will

not lift

load

Jack will

lift load,

but will

not hold

Jack will

not lower

completely

Poor jack

lifting.

Pump

feels

spongy

Jack will

not lift to

full height

Handle

raises by

itself when

jack is

under load

LUBRICATION

• Add lubrication oil to all moving parts

every 3 months.

PREVENTING RUST

• Check Piston Rod & Pump Piston

every 3 months for any signs of rust or

corrosion. Clean as needed and wipe

with an oily cloth.

• When not using the jack, always leave

the saddle & pump piston all the way

down.

KNOW YOUR JACK

Compare these illustrations with your

jack before operation and/or oil level

maintenance to become familiar with

the location of jack components.

RELEASE

VALVE

PUMP PISTON

DOWN

PROPER OIL

LEVEL

OIL FILLER

PLUG

PISTON ROD ALL

THE WAY IN

WARRANTY

1. This product is covered by an express warranty for 12 months from the date of purchase by

the original purchaser. Subject to the conditions of this warranty Shinn Fu Australia Pty Ltd

will replace the product or provide necessary parts on the product if the product is found to be

faulty within the warranty period due to defect in material or workmanship.

2. This warranty only applies to products imported by Shinn Fu Australia Pty Ltd and used within

Australia. Shinn Fu products imported by other importers are specically excluded.

3. This warranty only applies if the product has been used under normal conditions and in

accordance with the User Manual and that, in the opinion of Shinn Fu Australia Pty Ltd,

reasonable care has been taken of the product.

4. This warranty is void if the product has been tampered with or repaired by any unauthorised

person or has been modied in any way. Any abuse, misuse or subject to normal wear and tear

is not covered by this warranty.

5. If a warranty service is required the purchaser should:

a. Take the product to the nearest Shinn Fu Australia Pty Ltd repair agent or return it to the

place of purchase, at purchaser cost.

b. Provide evidence of proof of purchase and the date of purchase.

c. Provide details of the problem encountered.

6. The benets provided to the consumer by this warranty are in addition to other rights and

remedies available to the consumer under the law.

IF YOU REQUIRE ANY ASSISTANCE REGARDING WARRANTY CONDITIONS PLEASE

CONTACT THE SHINN FU AUSTRALIA PTY LTD COMPLIANCE OFFICER ON (03) 9755 8277

OR EMAIL: [email protected]

Consumer Guarantees

Our goods come with guarantees that cannot be excluded under the Australian Consumer Law.

You are entitled to a replacement or refund for a major failure and compensation for any other

reasonably foreseeable loss or damage. You are also entitled to have the goods repaired or replaced

if the goods fail to be of acceptable quality and the failure does not amount to a major failure.

Shinn Fu (Australia) PTY. LTD.

15 Viewtech Place, Rowville, Victoria 3178, Australia

Indice

Altri manuali Pro-Lift Jack

Pro-Lift

Pro-Lift F-2332A Istruzioni per l’uso

Pro-Lift

Pro-Lift T-2501 Manuale utente

Pro-Lift

Pro-Lift G2000SA Manuale utente

Pro-Lift

Pro-Lift SG-5625 Istruzioni per l’uso

Pro-Lift

Pro-Lift F-2330BMC Istruzioni per l’uso

Pro-Lift

Pro-Lift F1650 Manuale utente

Pro-Lift

Pro-Lift F1650A Manuale utente

Pro-Lift

Pro-Lift F1500A Manuale utente

Pro-Lift

Pro-Lift F2000 Manuale utente

Pro-Lift

Pro-Lift F2000A Manuale utente

Pro-Lift

Pro-Lift G-737 Istruzioni per l’uso

Pro-Lift

Pro-Lift B-002NC Istruzioni per l’uso

Pro-Lift

Pro-Lift PL3300 Istruzioni per l’uso

Pro-Lift

Pro-Lift G-4630JSC Istruzioni per l’uso

Pro-Lift

Pro-Lift PL1002 Manuale utente

Pro-Lift

Pro-Lift PL3200 Istruzioni per l’uso

Pro-Lift

Pro-Lift F1800A Manuale utente

Pro-Lift

Pro-Lift T-9446 Istruzioni per l’uso

Pro-Lift

Pro-Lift B-1850 Manuale utente

Pro-Lift

Pro-Lift B-033D Istruzioni per l’uso

Pro-Lift

Pro-Lift F1800 Manuale utente

Pro-Lift

Pro-Lift Garage in a Box Istruzioni per l’uso

Pro-Lift

Pro-Lift T-9400 Istruzioni per l’uso

Pro-Lift

Pro-Lift PRO-A1200 Manuale utente

Manuali Jack popolari di altre marche

Omega Lift Equipment

Omega Lift Equipment 18122C Istruzioni per l’uso

Pittsburgh

Pittsburgh 58816 Istruzioni per il montaggio

Unimec

Unimec TP Manuale utente

Sonic

Sonic 4800703 Manuale utente

BGS technic

BGS technic 70039 Manuale utente

TradeQuip

TradeQuip 1128T Manuale utente

VEVOR

VEVOR TJD-12000SP-F Manuale utente

ULTIMATE SPEED

ULTIMATE SPEED URW 2 A1 HYDRAULIC TROLLEY JACK Manuale utente

Stels

Stels 51131 Manuale utente

Bushranger

Bushranger RJX01 Manuale utente

Clarke

Clarke CTJ2500QLG Manuale di installazione e funzionamento

Valex

Valex 1650520 Manuale utente

Pfaff

Pfaff Merkur M0 Manuale utente

Beta

Beta 3050/K Supplemento

Sealey

Sealey 1050CXHV Manuale utente

Jung

Jung JH Series Manuale utente

URIAH

URIAH UC200020 Manuale utente

Kennedy

Kennedy KSJ010 Manuale utente