ProFusion EH-4604 Manuale utente

INSTRUCTION MANUAL

Heavy Electric Utility Heater

Model：EH-4604

Figure 1

Technical Support: 1-866-206-0888

IMPORTANT INSTRUCTIONS

When using electrical appliances, basic precautions should always be followed

to reduce the risk of fire, electric shock, and injury to persons, including the

following:

1. Read all instructions before installing or using this heater.

2. This heater is hot when in use. To avoid burns, do not let bare skin touch hot

surfaces.

Keep combustible materials, such as furniture, pillows, bedding, papers,

clothes, and curtains at least 3 feet (0.9 m) from the front of the heater and

keep them away from the sides and rear.

3. Extreme caution is necessary when any heater is used by or near children

or invalids and whenever the heater is left operating and unattended.

4. Always turn off the power of heater when not in use.

5. Do not operate any heater with the heater malfunctions, has been dropped

or damaged in any manner. Return heater to authorized service facility for

examination, electrical or mechanical adjustment, or repair.

6. Do not use outdoors.

7. This heater is not intended for use in bathrooms, laundry areas and similar

indoor locations. Never locate heater where it may fall into a bathtub or other

water container.

8. To disconnect heater, turn controls to off.

9. Do not insert or allow foreign objects to enter any ventilation or exhaust

opening as this may cause an electric shock or fire, or damage the heater.

10. To prevent a possible fire, do not block air intakes or exhaust in any

manner. Do not use on soft surfaces, like a bed, where openings may become

blocked.

11. Aheater has hot and arcing or sparking parts inside. Do not use it in areas

where gasoline, paint, or flammable liquids are used or stored.

12. Use this heater only as described in this manual. Any other use not

recommended by the manufacturer may cause fire, electric shock, or injury to

persons.

13. This heater may include an audible (a visual) alarm to warn that parts of

the heater are getting excessively hot. If the alarm flashes, immediately turn

the heater off and inspect for any objects on or adjacent to the heater that may

cause high temperatures. DO NOT OPERATE THE HEATER WITH THE

ALARM FLASHING.

SAVE THESE INSTRUCTIONS

DESCRIPTION

Electric utility heaters are designed to meet a variety of heating requirements

by switching a few wires located in the base of the unit. Heat output is 17 065

BTU per hour. Features horizontal and vertical flow horizontal air flow. Built-in

thermostat with overheating safety thermal cutout.

SPECIFICATIONS

Rating

AMPS

BTU/hour

5000W III 240-1-60

20.9

17065

4000W II 240-1-60

16.7

14105

3000W I 240-1-60

12.5

11285

GENERAL SAFETY INFORMATION

WARNING: This heater requires hardwire installation (no plug).

The installation of this product must be carried out by a

Certified Electrician and in accordance with all local and

national electrical codes.

Read and understand all installation & operation

instructions prior to operating this unit. Observe all safety instructions.

1. Use only copper wires rated for at least 60ºC.

2. Heater air flow must be directed parallel to or away from adjacent wall.

3. Observe all wall, floor and ceiling clearance requirements.

4. All wiring must be done according to national and local electrical codes.

The heater must be grounded as a precaution against possible electrical

shock. Heater circuit must be protected with proper fuses.

5. The mounting structure and the anchoring hardware must be capable of

supporting the weight of the heater and the mounting bracket (if used).

6. All electrical power must be disconnected at the main service box, which

must be locked before connecting, inspecting, cleaning or servicing the

hater. This is an important precaution to prevent serious electric shock.

7. This is heater is not suitable for use in hazardous locations containing

explosive liquids or vapours. This heater has hot or arcing or sparking

pads inside. Do not use it in areas where gasoline, paint or flammable

liquids are used or stored.

8. This heater is not suitable for use in corrosive atmospheres such as

marine greenhouses or chemical storage areas.

9. This heater must be mounted at least 8 feet off the floor. For specific

clearances, please see next page.

Improper installation or failure to follow the procedures

outlined in this instruction manual can result in serious electrical shock.

LOCATING HEATER

Install heater away from traffic areas, maintaining clearances stated in figure 2

(below). The air flow direction should not be restricted (ie. by columns or

machinery). The air flow should wipe exposed walls rather than blowing

directly on them. When more than one heater is used in an area, heaters

should be installed so that the air discharge of each heater supports the air

flow of the others, to provide best warm air circulation as shown in figure 3.

Figure 2

Figure 3

INSTALLATION

MOUNTING THE BRACKET

Refer to Figures 4a and 4b.

1. Locate a wood stud in the wood ceiling joist. If you cannot locate a wood

stud, you have to install a wood piece on the ceiling as this heater must be

securely fastened.

2. Remove the mounting bracket from the heating unit by loosening bracket

screws with a wrench and slipping the handle off over the screw heads.

3. Place a washer on screws before inserting through the holes in the

mounting bracket and screw them securely into a ceiling joist.

NOTE: If you want to swivel the heater either to the right or left adding a

washer to both sides of the bracket is recommended. Alonger lag bolt may be

required to properly secure the unit. See Figure 4a.

HANGING THE HEATER

1) Attach the heating unit to the mounting bracket.

2) Lift the heater up and into the mounting bracket.

3) Align the bracket screws with the keyhole slots in the mounting bracket.

4) If the heater is to be tilted it must be positioned in the keyhole slots - see

figure 5.

5) Tighten the bracket screws with a wrench so the unit is securely

suspended at horizontal or vertical level.

Wood Ceiling

Figure 5

CONNECTING THE POWER

Warning: This appliance must be grounded!

Warning: The appliance must connect to a current protection circuit or

device at 50Amp or less before being connected to power supply!

1. Remove the screw from the front of the unit to connect the power to the

heater.

2. Attach the cable connectors to the unit (See Figure 6) and slide the

10-gauge wire through the cable connector.

NOTE: All wiring must be accordance to national and local electrical codes in

the United States. For certain applications conduit may be required See Figure

6. Check local electrical codes. If you run the wiring in conduit and wish to be

able to turn the heater be sure to purchase enough flexible conduit to allow the

heater to be turned.

3. Connect the wire to the power block located in the base of the heater - See

Figure 7.

4. Turn on the power at the main service.

CAUTION:

High temperatures –risk of fire. Keep flammable materials, such as furniture,

pillows, bedding, papers, clothes and curtains at least 3 ft. (0.9 m) from the

front and top of the heater and keep them away from the sides and rear.

To reduce the risk of fire, do not use it in areas where gasoline, paint or flammable

liquids are used or stored.

OPERATING INSTRUCTIONS

WARNING: the heater must be properly installed before it is used.

SETTING THE THERMOSTAT

1) Rotate thermostat knob clockwise to high position, POWER INDICATOR

will turn yellow.

2) After room reaches desired comfort level rotate thermostat knob counter

clockwise until the thermostat to OFF position.

NOTE: Heater will cycle on and off to maintain room temperature.

SELECTION SWITCH

Using the SELECTION SWITCH, you can control the heating

output: I for 3000W, II for 4000W, III for 5000W.

THERMAL CUT-OUT

The heater will automatically shut off when parts of it overheat. The heater will

turn ON again when the abnormal temperature returns to normal levels.

Should the unit overheat and cause the thermal cut-out to cycle, the cause of

the overheating should be determined and corrective action taken before

further operation.

NOTE: When the thermal cut-out is activated, the caution indicator will turn red.

In this case, immediately turn the heater OFF and inspect for any objects on or

adjacent to the heater that may cause high temperatures. DO NOT OPERATE

THE HEATER WITH THE CAUTION INDICATOIR GLOWING RED.

THERMOSTAT

SELECTION

SWITCH

POWER

INDICATOR

(yellow)

CAUTION

INDICATOR

(red)

III I II

selection switch

ADJUSTING AIR FLOW DIRECTION

1. To turn the unit when it has been installed with a single lag bolt (as shown in

figure 4a), simply turn the entire heater as needed. The unit cannot be turned

horizontally if it has been installed with 2 lag bolts.

2. To tilt the unit vertically, loosen the bracket screws (see figure 5).

NOTE: For the heater to be tilted vertically, it must be mounted in bottom

keyhole slots of mounting brackets to maintain adequate clearance and

prevent possible overheating.

1. Adjust louvers to the desired position.

NOTE: The louvers are designed so they cannot be completely closed. Do not

attempt to defeat this feature; damage to the unit can result.

To prevent possible electric shock, disconnect power to the

heater at the main service box before attempting to adjust the heat output of

this unit.

MAINTENANCE INSTRUCTIONS

MAINTENANCE AND CLEANING

1. Before cleaning, make sure the power has been turned off at the circuit

breaker panel and that the heating element of the heater is cool.

2. To maintain the external appearance of the radiator, it need only be wiped

over occasionally with a dry duster. During the summer months, or at other

times when the appliance is not in use and is completely cold, It should be

the best opportunity to wipe over with a damp cloth.

3. Do not use abrasive clearing powders or furniture polish. Do not use

chemical or abrasive products, metallic scourers and so on, which may

deteriorate the surface, to clean the appliance.

4. All other servicing should be performed by qualified service personnel. Do

not try to repair the heater yourself.

Indice

Altri manuali ProFusion Stufa

ProFusion

ProFusion DQ1016A Manuale utente

ProFusion

ProFusion HA24-50MB Manuale utente

ProFusion

ProFusion HA24-50E Manuale utente

ProFusion

ProFusion PH-934 Manuale utente

ProFusion

ProFusion PH-960XNR Manuale utente

ProFusion

ProFusion SHAG-L02F Manuale utente

ProFusion

ProFusion HA24-75MB Manuale utente

ProFusion

ProFusion GD8110BP-M Manuale utente

ProFusion

ProFusion PH-960N Manuale utente

ProFusion

ProFusion HA22-48M Manuale utente

ProFusion

ProFusion PH-9100WN Manuale utente

ProFusion

ProFusion PH-9100WS Manuale utente

ProFusion

ProFusion WH-50B Manuale utente

ProFusion

ProFusion QH-1 Manuale del proprietario

ProFusion

ProFusion PH-931 Manuale utente

ProFusion

ProFusion HFU15-E Manuale utente

ProFusion

ProFusion TV15LR Manuale utente

ProFusion

ProFusion PH-960 Manuale utente

ProFusion

ProFusion HA11-20M Manuale utente

ProFusion

ProFusion PH-9100WRN Manuale utente

ProFusion

ProFusion H-5511 Manuale utente

ProFusion

ProFusion NDB-1Y Manuale utente

ProFusion

ProFusion GD9315BC1-N Manuale utente

ProFusion

ProFusion EH-4601 Manuale utente

Manuali Stufa popolari di altre marche

oventrop

oventrop Regucor Series Manuale utente

Blaze King

Blaze King CLARITY CL2118.IPI.1 Manuale utente

ELMEKO

ELMEKO ML 150 Manuale utente

BN Thermic

BN Thermic 830T Manuale utente

KING

KING K Series Guida

Empire Comfort Systems

Empire Comfort Systems RH-50-5 Guida rapida

Well Straler

Well Straler RC-16B Manuale utente

EUROM

EUROM 333299 Manuale utente

Heylo

Heylo K 170 Manuale utente

Eterna

Eterna TR70W Manuale utente

Clarke

Clarke GRH15 Manuale di istruzioni

IRSAP

IRSAP The Radiator Company Ovali Manuale utente

Empire Heating Systems

Empire Heating Systems WCC65 Manuale utente

Wetekom

Wetekom 92 86 43 Manuale utente

Desa

Desa SPC170-F Manuale utente

Watlow

Watlow Watrod Electric Tubular Heaters Manuale utente

Haverland

Haverland ECO-DRY GPS Series Manuale elenco delle parti

Stelpro

Stelpro ASILVC2060 Series Manuale utente