Progress Lighting AirPro P250099 Manuale utente

P250099

93165620_A

Limited Lifetime Warranty

Date Purchased

Store Purchased

UL Model No.

Serial No.

Vendor No.

UPC

111017

P250099

Progress Lighting fan motors are warranted to the original purchaser to be free of electrical and/or mechanical

defects for so long as the original purchaser owns the fan. Pull chain switches, reverse switches, capacitors and

metal nishes are warranted to be free from defects in materials or workmanship for a period of 1 year from

the date of purchase. Warping of wooden or plastic blades is not covered by this warranty nor is corrosion and/

or deterioration of any nishes for fans installed within ten miles of any sea coast. Extended warranties for

ENERGY STAR® qualied products may apply.

Progress Lighting ceiling fans with built-in LED light sources, when properly installed and under normal

conditions of use, are warranted to be free from defects in material and workmanship which cause the light

sources to fail to operate in accordance with the specications for (i) ve (5) years from the date of purchase

on the LED Light modules and electrical components for fans used in single family residences, and (ii) three

(3) years from the date of purchase on the LED Light modules and electrical components for fans used in

multi-family or commercial applications. LED bulbs supplied by Progress Lighting carry no warranty other

than manufacturer’s warranty. Non-LED bulbs carry no warranty.

With proof of purchase, the original purchaser may return the defective fan to the place of purchase during the

rst 30 days for replacement. After 30 days, the original purchaser MUST contact Progress Lighting at (864)

678-1000 for repair or replacement which shall be determined in Progress Lighting’s sole discretion and shall

be purchaser’s sole and exclusive remedy.

Labor and Shipping Excluded. This warranty does not cover any costs or fees associated with the labor

(including, but not limited to, electrician’s fees) required to install, remove, or replace a fan or any fan parts.

This warranty shall not apply to any loss or damage resulting from (i) normal wear and tear or alteration,

misuse, abuse or neglect, or (ii) improper installation, operation, repair or maintenance by original purchaser

or a third party, including without limitation improper voltage supply or power surge, use of improper parts or

accessories, unauthorized repair (made or attempted) or failure to provide maintenance to the fan.

THE FOREGOING WARRANTIES STATE PROGRESS LIGHTING’S ENTIRE WARRANTY OBLIGATION

AND ORIGINAL PURCHASER’S SOLE AND EXCLUSIVE REMEDY RELATED TO SUCH PRODUCTS.

PROGRESS LIGHTING IS NOT RESPONSIBLE FOR DAMAGES (INCLUDING INDIRECT, SPECIAL,

INCIDENTAL OR CONSEQUENTIAL), DUE TO PRODUCT FAILURE, WHETHER ARISING OUT OF

BREACH OF WARRANTY, BREACH OF CONTRACT, OR OTHERWISE. THIS WARRANTY IS GIVEN

IN LIEU OF ALL OTHER WARRANTIES, WHETHER EXPRESSED OR IMPLIED, INCLUDING THOSE

OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE OR NON INFRINGEMENT.

Some states do not allow limitations on how long an implied warranty lasts or the exclusion or limitations

of incidental or consequential damages, so the above limitations and exclusions may not apply to you. This

warranty gives you specic rights and you may have other rights which vary from state to state.

785247255474

785247255481

Safety Rules

Unpacking Your Fan

Installing Your Fan

Making the Electrical Connections

Operating Your Fan

Care of Your Fan

Troubleshooting

Specications

Table of Contents

1. To reduce the risk of electric shock, insure electricity has been

turned off at the circuit breaker or fuse box before beginning.

2. All wiring must be in accordance with the National Electrical

Code ANSI/NFPA 70-1999 and local electrical codes.

Electrical installation should be performed by a qualied

licensed electrician.

3. CAUTION: To reduce the risk of personal injury, use only the

screws provided with the electrical box.

4. The outlet box and support structure must be securely

mounted and capable of reliably supporting 35 lbs. (15.9 kg).

Use only cUL Listed outlet boxes marked “Acceptable for Fan

Support of 35 lbs. (15.9 kg) or less.”

5. CAUTION: The fan must be mounted with a minimum of 7

feet clearance from the trailing edge of the blades to the oor.

6. Do not wait for the fan to stop before pressing the reverse

button. The fan will not reverse direction if the fan is not

moving.

7. Avoid placing objects in path of the blades.

8. To avoid personal injury or damage to the fan and other items,

be cautious when working around or cleaning the fan.

9. Do not use water or detergents when cleaning the fan or fan

blades. A dry dust cloth or lightly dampened cloth will be

suitable for most cleaning.

10. After making electrical connections, spliced conductors should

be turned upward and pushed carefully up into electrical box.

The wires should be spread apart with the grounded conductor

and the equipment-grounding conductor on one side of the

electrical box and ungrounded conductor on the other side of

the electrical box.

11. Electrical diagrams are for reference only. Light kits that

are not packed with the fan must be UL Listed and marked

suitable for use with the model fan you are installing. Switches

must be UL General Use Switches. Refer to the instructions

packaged with the light kits and switches for proper assembly.

12. All set screws must be checked and retightened where

necessary before installation.

13. WARNING: To reduce the risk of re or electric shock, this

fan should only be used with speed controller UC7312RE,

manufactured by Rhine Electronic Co., Ltd.

1. Safety Rules

READ AND SAVE THESE INSTRUCTIONS

TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK OR PERSONAL

INJURY, MOUNT TO OUTLET BOX MARKED “ACCEPTABLE FOR FAN

SUPPORT OF 35LBS. (15.9 KG) OR LESS”, AND USE SCREWS PRO-

VIDED WITH THE OUTLET BOX.

TO REDUCE THE RISK OF PERSONAL INJURY, DO NOT BEND THE

BLADE BRACKETS (ALSO REFERRED TO AS (“FLANGES”) DURING

ASSEMBLY OR AFTER INSTALLATION. DO NOT INSERT OBJECTS IN

THE PATH OF THE BLADES.

TO REDUCE THE RISK OF SHOCK, THIS FAN MUST BE INSTALLED

WITH AN ISOLATION WALL CONTROL/SWITCH.

a. Blade arm attachment hardware

(19 screws)

b. Electrical hardware and balancing kit

(3 plastic wire connector, blade balancing kit)

c. Blade bracket attachment hardware

(1 extra screw for attaching blade arm to the

fan motor assembly)

6. Light Kit Pan

7. Light Kit Fitter Assembly

8. Light Shade

9. Remote Control

1. Mounting Plate

2. Fan Motor Assembly

3. Housing

4. Blade Arm

5. Blade

2. Unpacking Your Fan

Unpack your fan and check the contents. You should have the following items:

3. Installing Your Fan

Tools Required

Phillips screw driver or straight slotted screw

driver, adjustable wrench, step ladder, and

wire cutters.

Mounting Options

If there isn’t an existing electrical box, then

read the following instructions. Disconnect

the power by removing fuses or turning off

circuit breakers.

Secure the electrical box directly to the building

structure. Use appropriate fasteners and

building materials. The electrical box and

its support must be able to fully support the

moving weight of the fan (at least 35 lbs.).

Do not use plastic electrical boxes.

Figures 1, 2, and 3 are examples of different

ways to mount the electrical box.

Note: You may need a longer downrod to

maintain proper blade clearance when installing

on a steep, sloped ceiling. The maximum

angle allowable is 20˚. If the canopy touches

downrod, turn the canopy 180˚ before

attaching the canopy to the mounting plate.

To hang your fan where there is an existing

xture but no ceiling joist, you may need an

installation hanger bar as shown in Figure 4.

TO REDUCE THE RISK OF FIRE, ELECTRIC

SHOCK OR PERSONAL INJURY, MOUNT

TO OUTLET BOX MARKED “ACCEPTABLE

FOR FAN SUPPORT OF 35LBS. (15.9 KG) OR

LESS”, AND USE SCREWS PROVIDED WITH

THE OUTLET BOX. ELECTRICAL BOXES

COMMONLY USED FOR THE SUPPORT OF

LIGHTING FIXTURES MAY NOT BE ACCEPT-

ABLE FOR FAN SUPPORT AND MAY NEED TO

BE REPLACED. CONSULT A QUALIFIED ELEC-

TRICIAN IF IN DOUBT.

Figure 1

Figure 2

Figure 4

Figure 3

4. Hanging the Fan

Figure 5 Figure 6

Figure 7

Hanging the fan-motor

assembly

1. Carefully lift the fan-motor assembly and

engage the slot in the motor bracket on the

top of the fan-motor assembly with the

hook on the mounting plate so that it is

securely suspended. (Figure 6)

Then connect the wiring to your fan

according to step 5 “Making the Electrical

Connections” found on next page.

2. Once the wiring is completed, lift the fan-

motor assembly.

3. Align the holes in the mounting plate

with the pre attached screws on the motor

bracket.

4. Securely tighten the screws.

Washers

UL listed

electrical box

Mounting

screws

Mounting

plate

Hook

Fan-motor

assembly

Slot

Motor

bracket

Mounting plate

Fan-motor

assembly

Motor

bracket

Screw

REMEMBER to turn off the power. Follow

the steps below to hang your fan properly.

NOTE: For better fan performance, make

sure the mounting plate is level. Additional

washers (not included) may be needed to

insert between the outlet box and mounting

plate.

Attaching the fan to the

electrical box

1. Turn the power off.

2. Securely attach the mounting plate to the

outlet box using the two screws supplied

with the outlet box. Pull the 120-volt

supply wires (black, white and ground

wires) out of the outlet box and through

the hole in the mounting plate and lay

them to the side. (Figure 5)

5. Electrical Connections

Making the electrical

connections

1. Connect the ground conductor of the 120-

Volt supply (this may be a bare wire or a

wire with green colored insulation) to the

green wire from the motor bracket using a

plastic wire connecting nut. (Figure 8)

2. Connect the fan motor white wire to the

household white wire using a plastic wire

connecting nut. (Figure 8)

3. Connect the fan motor black wire wire to

the household black wire using a plastic

wire connecting nut. (Figure 8)

4. Secure each wire connecting nut using

electrical tape. Turn the wire connecting

nut upward and push the wiring into the

outlet box.

EACH WIRE CONNECTING NUT SUPPLIED

WITH THIS FAN IS DESIGNED TO ACCEPT UP

TO ONE 12-GAUGE HOUSE WIRE AND TWO

WIRES FROM THE FAN. IF YOU HAVE LARGER

THAN 12-GAUGE HOUSE WIRING OR MORE

THAN ONE HOUSE WIRE TO CONNECT TO THE

FAN WIRING, CONSULT AN ELECTRICIAN FOR

THE PROPER SIZE WIRE NUTS TO USE.

Figure 9

Figure 8

BLACK

WHITE

GREEN

Outlet

box

BLACK

WHITE

Installing the motor housing

1. Remove two of the four screws (located

diagonally from each other) from the top

of the mounting plate and loosen the other

two screws.

2. Align the two key slots in the top of the

motor housing with the two loosened

screws on the mounting plate. Push the

motor housing up and turn it clockwise to

lock in the mounting plate. Tighten the two

screws.

3. Install the two screws that were removed

at the beginning of this step into the

remaining two holes and tighten the four

screws rmly. (Figure 9)

Screws

Motor Assembly

Blade arm

1/8”. Run the fan for 10 minutes.

3. Make sure that canopy is tightened

securely to ceiling mounting bracket

and that the ceiling mounting bracket is

tightened securely to the electrical box.

4. Interchanging two adjacent blades can

redistribute the weight and possibly result

in the smoother operation.

5. Use the enclosed blade balancing kit if the

blade wobble is still noticeable.

Figure 10

6. Attaching the Blades

Figure 11

Attaching the blade

brackets to the blades

1. Attach blade to blade bracket using the

screws as shown in gure 10. Start a

screw into the bracket. Repeat for the two

remaining screws.

2. Tighten each screw securely.

Attaching the blade

1. Fasten the blade assembly to the motor by

inserting the alignment post into the slot

on the bottom of the motor and tightening

the motor screws. Please note that the

motor screws are pre-attached into the

blade brackets (Figure 11).

2. Repeat step 1 for the remaining blades.

Blade balancing

All blades are grouped by weight. Because

materials vary in density, the fan may wobble

even though the blades are weight matched.

The following procedure should correct most

fan wobble. Check after each step.

1. Check that all blade screws are secure.

2. Most fan wobble problems are caused

when blade levels are unequal. Check this

level by selecting a point on the ceiling

above the tip of one of the blades. Measure

from a point on the center of each blade

to the point on the ceiling. Measure this

distance as shown in Figure 12. Rotate

the fan until the next blade is positioned

for measurement. Repeat for each blade.

Measurements deviation should be within

Figure 12

Screws

Blade

Blade arm

Touching

ceiling

NOTE: Your fan blades are reversible. Select

the blade side nish which best accentuates

your decor.

Glass Shade

Flat Area

Raised

Dimples

Light kit fitter

assembly

Screws

Black White

White

Blue

Light Kit

Pan

Screws

Light Kit Pan

7. Installing Light Kit

Installing the Light Kit Pan/

Light Kit Fitter Assembly/

Light Shade

CAUTION - To reduce the risk of electrical

shock, disconnect the electrical supply circuit

to the fan before installing the light kit.

1. Loosen but do not remove two of three

mounting screws from the fan motor

assembly; Remove one mounting screw.

(Figure 13)

2. Push the light kit pan up to the fan motor

assembly so that the two loosened screw

heads t into the keyhole slots. Turn the

light kit pan clockwise, then tighten the

screws. Re-install the screw that was

removed in step 1 and tighten rmly.

(Figure 13)

3. Remove one screw from the light kit pan

and loosen, but do not remove the other

two screws. Connect the wires from the

light kit tter assembly to the wires from

the fan motor assembly by connecting the

molded adaptor plugs together. Carefully

tuck all wires and splices into the switch

cap. (Figure 14)

4. Push the light kit tter assembly up so

that the two loosened screw heads t into

the keyhole slots. Turn the light kit tter

assembly clockwise, tighten the screws.

Re-install the screw that was removed in

step 3 and tighten rmly. (Figure 14)

5. Place the shade into the light kit pan,

aligning the three at areas on the top of

the shade with the three raised dimples in

the light kit pan. Turn the shade clockwise

until it stops. Make sure to twist the lens

in completely. Exert enough force to get

over the rst bump and twist completely in.

(Figure 15)

Figure 13

Figure 14

PERIODICALLY CHECK THE GLASS SHADE IS

SEATED FULLY CLOCKWISE IN THE LIGHT KIT

PAN ASSEMBLY.

Figure 15

Indice

Lingue:

Altri manuali Progress Lighting Fan

Progress Lighting

Progress Lighting AirPro P250093 Manuale utente

Progress Lighting

Progress Lighting P2514 Manuale utente

Progress Lighting

Progress Lighting AirPro COPAN Manuale utente

Progress Lighting

Progress Lighting AirPro P250110 Manuale utente

Progress Lighting

Progress Lighting AirPro Willacy P250063 Manuale utente

Progress Lighting

Progress Lighting Springer P260004 Manuale utente

Progress Lighting

Progress Lighting P250020 Manuale utente

Progress Lighting

Progress Lighting AirPro P2584 Manuale utente

Progress Lighting

Progress Lighting AirPro P2554 Manuale utente

Progress Lighting

Progress Lighting AirPro P2562 Manuale utente

Progress Lighting

Progress Lighting AirPro P250034 Manuale utente

Progress Lighting

Progress Lighting AirPro P250060 Manuale utente

Progress Lighting

Progress Lighting AirPro P250094 Manuale utente

Progress Lighting

Progress Lighting AirPro P250102 Manuale utente

Progress Lighting

Progress Lighting AirPro P250070 Manuale utente

Progress Lighting

Progress Lighting AirPro P2572 Manuale utente

Progress Lighting

Progress Lighting AirPro P250072 Manuale utente

Progress Lighting

Progress Lighting AirPro P2564-3030K Manuale utente

Progress Lighting

Progress Lighting AirPro P250024 Manuale utente

Progress Lighting

Progress Lighting AirPro P2540 Manuale utente

Progress Lighting

Progress Lighting P2667 Manuale di programmazione

Progress Lighting

Progress Lighting Airpro P250073 Manuale utente

Progress Lighting

Progress Lighting AirPro P250058 Manuale utente

Progress Lighting

Progress Lighting EF200D Manuale utente

Manuali Fan popolari di altre marche

ELTA FANS

ELTA FANS H03VV-F Manuale utente

Hunter

Hunter 20714 Manuale di istruzioni

Emerson

Emerson CARRERA VERANDA CF542ORB00 Manuale utente

Hunter

Hunter Caraway Manuale di istruzioni

Panasonic

Panasonic FV-15NLFS1 Manuale utente

Kompernass

Kompernass KH 1150 Manuale utente

VES

VES FALA100/12V/TR Manuale utente

Vertiv

Vertiv Liebert DCD Manuale utente

Westinghouse

Westinghouse GFP Series Manuale utente

Venmar

Venmar KUBIX HRV PLUS Series Manuale utente

Maico

Maico ECR 31 Manuale utente

Sonnenkonig

Sonnenkonig Dinky Manuale utente

S&P

S&P ECOWATT HXBR Manuale utente

Wider

Wider IMP03369BH Manuale utente

Panasonic

Panasonic F-60DHN Manuale utente

Hinkley

Hinkley HIGHLAND Manuale utente

Broan

Broan 766BN Manuale utente

Premium

Premium PFS16022 Istruzioni per il montaggio