Prorack K324 Manuale utente
FittingKit
K324
GB
Fitting Instructions for Basic Carrier
x 8
x 4
x 4
x 4
1
Revision No:
1.1
FittingKit
K324
GB
First Time Installation
Remove parts from packaging and check
contents. Contact your Prorack dealer if parts
are missing or damaged.
This kit fits type A, B, C and D.
These instructions show type A crossbar
fitted. They also apply to type B, C and D.
Use keys to remove covers.
2
FittingKit
K324
GB
Use hex screwdriver to reverse adjusting
screw 10 turns.
Press adjusting screw and pull crossbar legs
out. Refer to the crossbar instructions for
crossbar adjustment.
Ensure each end of the crossbar is adjusted
equally.
Remove clamp block by pressing backwards.
3
FittingKit
K324
GB
Remove both pins from each leg (use
spanner located inside left hand cover to
assist).
Detach foot from leg. Store loose parts in a
safe place.
Repeat for all legs.
Select a guttermount assembly from fitting
kit. Unscrew and remove clamps.
4
FittingKit
K324
GB
Assemble guttermount assembly into leg
(ensure guttermount blade interlocks with
leg).
Using short capscrew and washer, secure
assembly onto leg (use Hex Screwdriver
supplied with crossbar to assist)
Use two M5 x 12 mm self tapping screws to
secure the leg to the guttermount blade.
Do not over tighten.
Repeat for all legs.
5
FittingKit
K324
GB
Fitment
Place crossbar on vehicle. Minimum
recommended spacing between the bars is
700mm (unless otherwise stated).
Place crossbar into gutter of vehicle.
Adjust crossbar in or out to suit vehicle.
Refer to the crossbar instructions for
crossbar adjustment.
Loosely position crossbar ensuring the
guttermount blade is hard against the inside
of the vehicle gutter.
Tighten adjusting screw to 5 Nm.
6
FittingKit
K324
GB
Loosely line up clamp over the vehicle gutter.
Use same capscrew and washer to secure
clamp onto leg.
Repeat for all legs.
Check crossbar is securely attached to the
vehicle.
Use keys to fit and lock covers
7
FittingKit
K324
GB
CAUTION:
Recheck all fasteners immediately after a load is
applied to the crossbars.
Regularly check screws are tight.
8
FittingKit
K324
GB
Maintenance
Clean the car roof and surfaces of the
product that will be in contact with the car
roof.
Follow the fitting instructions for fitting the
product to your vehicle. Make sure all steps
are carried out in order.
Set crossbars a minimum distance of 700mm
apart where no other distance is specified in
the fitting instructions. This is especially
important when carrying long loads.
Check unit is securely attached whenever
you refit it to the vehicle. If the unit feels
loose, refer to the fitting instructions and
readjust.
Some sunroofs and radio antennae cannot
be used when the product is fitted.
Do not modify this product.
Refer to the maximum permitted load
capacity specified in the fitting instructions.
Do not exceed the vehicle manufacturers
roof load rating if it is lower than the
maximum load capacity specified in the fitting
instructions.
Loads should not overhang the sides of the
product and be evenly distributed with the
lowest possible centre of gravity.
Long loads should be secured with non-
elastic straps to the front and rear of the
vehicle.
Objects with pointed ends (skis) should be
carried with the pointed ends to the rear of
the vehicle.
Remove all loose or removable objects from
the load prior to loading.
Make sure all loads are securely fastened
with non-elastic straps. Check regularly
during longer journeys.
9
FittingKit
K324
GB
A loaded roof rack system can alter the
performance of your vehicle. Be especially
aware of the effects of side winds, changing
of direction, and braking performance. Avoid
rapid acceleration and deceleration. Drive
carefully.
Note that the total height of the vehicle
increases when upright loads are carried.
Products should be locked during transport if
they have locks fitted.
Check and replace worn out or defective
parts.
Keep the product clean and maintained.
Never drive into a car wash with the roof rack
system fitted.
Lubricate locks and adjusting screws at
regular intervals.
Remove the products from the vehicle when
not in use. Make sure all loose parts are
stored safely.
Hubco Automotive Ltd
P. O. Box 11017
Christchurch
NEW ZEALAND
www.whispbar.com
10
Indice
Altri manuali Prorack Accessori per automobili
Prorack
Prorack K442 Manuale utente
Prorack
Prorack K951 Manuale utente
Prorack
Prorack K431 Manuale utente
Prorack
Prorack K390 Manuale utente
Prorack
Prorack K381W Manuale utente
Prorack
Prorack K458 Manuale utente
Prorack
Prorack EXP360 Manuale utente
Prorack
Prorack K813 Manuale utente
Prorack
Prorack K589 Manuale utente
Prorack
Prorack K178 Manuale utente
Prorack
Prorack K1001 Manuale utente
Prorack
Prorack K143 Manuale utente
Prorack
Prorack K420 Manuale utente
Prorack
Prorack K105 Manuale utente
Prorack
Prorack K782 Manuale operativo e di installazione
Prorack
Prorack WHISPBAR S41 Manuale operativo e di installazione
Prorack
Prorack K677 Manuale operativo e di installazione
Prorack
Prorack PR3205 Manuale utente
Prorack
Prorack K364 Manuale utente
Prorack
Prorack K063 Manuale utente
