Prorack K824W Manuale utente
K824W
Fitting Kit
EN Fitting Instructions for Basic Carrier
x 1 x 1 x 1 x 1
x 1 x 1 x 1 x 1
Revision No: 1A 1
Fitting Kit K824W
x 1 x 1 x 1 x 1
x 1 x 1 x 1 x 1
2
Fitting Kit K824W
MAX kgs (lbs)
W/P WHD
Chevrolet
Cruze , 4dr Sedan 09-+ ZA 45 kgs (99 lbs) 45 kgs (99 lbs)
Cruze , 4dr Sedan 11-+ US 45 kgs (99 lbs) 45 kgs (99 lbs)
Cruze , 4dr Sedan Feb 09-+ EU 45 kgs (99 lbs) 45 kgs (99 lbs)
Holden
Cruze , 4dr Sedan Jun 09-+ NZ 45 kgs (99 lbs) 45 kgs (99 lbs)
Cruze , 4dr Sedan Jun 09-+ AU 45 kgs (99 lbs) 45 kgs (99 lbs)
3
Fitting Kit EN
K824W
Whispbar and Prorack Crossbars
●ATTENTION: Find latest revision
instructions on the Whispbar or Prorack
website, or see your local dealer.
For Whispbar visit:
www.whispbar.com.au/.co.nz/.co.uk/.com
For Prorack visit:
www.prorack.com.au/.co.nz
First Time Installation
●Remove parts from inside the package and
check. Contact your dealer if any parts are
missing or damaged.
●This kit fits type A, B, C and D.
●These instructions show type A crossbar
fitted. They also apply to type B, C and D.
4
Fitting Kit EN
K824W
NOTE: Clamp images in these instructions may
not be representative of the clamps in this kit
●Use keys to remove covers.
●Use hex screwdriver to reverse adjusting
screw 10 turns.
5
Fitting Kit EN
K824W
●Press adjusting screw and pull crossbar
legs out. Refer to the crossbar instructions
for crossbar adjustment method.
●Ensure each end of the crossbar is
adjusted equally.
●Remove locking screw.
●Apply protective strip as shown.
Trim if required.
●A, C = Clear
B, D = Black
●A = 00-17-017, 00-17-018
B = 00-17-011, 00-17-012
C = 00-17-015, 00-17-016
D = 00-17-013, 00-17-014
6
Fitting Kit EN
K824W
●It is important to put the clamps in the
correct position on the vehicle.
●Letters refer to the part numbers stamped
on clamps.
●Clamp Part Number:
A = A325
B = A326
C = A327
D = A328
●Attach clamp to each leg. NOTE; clamps
may have labels showing their positions on
the vehicle (For example; "Front Right").
●Refit locking screw so that it goes through
the hole in the clamp. Do not begin to
tighten the locking screw.
7
Fitting Kit EN
K824W
●Refer to the underside of the pad for the
part number.
●It is important to put the pads in the correct
position on the vehicle.
●Letters refer to the pad part numbers and
position.
●Pad Part Number:
A = 293
B = 294
C = 255
D = 296
●Place rubber pads (supplied with fitting kit)
on the vehicle roof. Pad may vary in shape
to that shown.
8
Fitting Kit EN
K824W
●Make sure the pad fits into the holes
underneath the foot.
Fitment
●Clamps directly to edge of roof under the
doors
●Please check the rear of this manual for
information relating specifically to your
vehicle.
●Place crossbar on vehicle. Minimum
recommended spacing between the bars is
700mm (27 1/2") (unless otherwise stated).
●Adjust the legs on the crossbar so that they
are positioned equally from the ends of the
crossbar, and the clamps engage firmly on
the body work of the vehicle.
9
Fitting Kit EN
K824W
●Tighten adjusting screw to 3 Nm (2.2 ft lb)
hand tight.
●Tighten locking screw on both legs evenly,
3 Nm (2.2 ft lb).
●Check crossbar is securely attached to the
vehicle.
10
Indice
Altri manuali Prorack Accessori per automobili
Prorack
Prorack K070 Manuale utente
Prorack
Prorack PR3075 Guida all'installazione
Prorack
Prorack K145 Manuale utente
Prorack
Prorack K004 Manuale utente
Prorack
Prorack K486 Manuale utente
Prorack
Prorack K455 Manuale utente
Prorack
Prorack K175 Manuale utente
Prorack
Prorack K1208 Manuale utente
Prorack
Prorack K843 Manuale utente
Prorack
Prorack K072 Manuale utente
Prorack
Prorack K485 Manuale utente
Prorack
Prorack K1020 Manuale utente
Prorack
Prorack K1018 Manuale utente
Prorack
Prorack K919 Manuale utente
Prorack
Prorack K062 Manuale utente
Prorack
Prorack K049 Manuale utente
Prorack
Prorack K189 Manuale utente
Prorack
Prorack PR3104 Manuale utente
Prorack
Prorack K423 Manuale utente
Prorack
Prorack VOYAGER PR3207 Manuale utente
