Prorack K983 Manuale utente
K983
Fitting Kit
EN Fitting Instructions for Basic Carrier
x 1 x 1 x 1 x 1
x 1 x 1 x 2 x 1
x 1 x 2
Revision No: 5E 1
Fitting Kit K983
MAX kgs (lbs)
W/P WHD
Kia
K5, 4dr Sedan 16-+ CN 65 kgs (143 lbs) 65 kgs (143 lbs)
Optima, 4dr Sedan Nov 15-+ AU 65 kgs (143 lbs) 65 kgs (143 lbs)
Optima, 4dr Sedan Nov 15-+ EU 65 kgs (143 lbs) 65 kgs (143 lbs)
Optima, 4dr Sedan Nov 15-+ NZ 65 kgs (143 lbs) 65 kgs (143 lbs)
2
Fitting Kit K983
X
A B C 1 2 3
K5, 4dr Sedan 16-+ (CN) -295mm 345mm - 884mm 852mm -
-11 -5/8ths" 13 9/16ths" - 34 13/16ths" 33 9/16ths" -
Optima, 4dr Sedan Nov 15-+ (AU) -295mm 345mm - 884mm 852mm -
-11 -5/8ths" 13 9/16ths" - 34 13/16ths" 33 9/16ths" -
Optima, 4dr Sedan Nov 15-+ (EU) -295mm 345mm - 884mm 852mm -
-11 -5/8ths" 13 9/16ths" - 34 13/16ths" 33 9/16ths" -
Optima, 4dr Sedan Nov 15-+ (NZ) -295mm 345mm - 884mm 852mm -
-11 -5/8ths" 13 9/16ths" - 34 13/16ths" 33 9/16ths" -
3
Fitting Kit EN
K983
First Time Installation
●Remove parts from inside the package and
check. Contact your dealer if any parts are
missing or damaged.
●This kit fits type A, B, C and D.
●These instructions show type A crossbar
fitted. They also apply to type B, C and D.
NOTE: Clamp images in these instructions may
not be representative of the clamps in this kit
4
Fitting Kit EN
K983
●Use keys to remove covers.
●Use hex screwdriver to reverse adjusting
screw 10 turns.
●Press adjusting screw and pull crossbar
legs out. Refer to the crossbar instructions
for crossbar adjustment method.
●Ensure each end of the crossbar is
adjusted equally.
5
Fitting Kit EN
K983
●Remove locking screw.
●Apply protective strip as shown.
Trim if required.
●It is important to put the clamps in the
correct position on the vehicle.
●Letters refer to the part numbers stamped
on clamps.
●Clamp Part Number:
A = A849
B = A850
C = A851
D = A852
6
Fitting Kit EN
K983
●Attach clamp to each leg. NOTE; clamps
may have labels showing their positions on
the vehicle (For example; "Front Right").
●Refit locking screw so that it goes through
the hole in the clamp. Do not begin to
tighten the locking screw.
●Refer to the underside of the pad for the
part number.
7
Fitting Kit EN
K983
●It is important to put the pads in the correct
position on the vehicle.
●Letters refer to the pad part numbers and
position.
●Pad Part Number:
A = 241
B = 293
C = 294
●Place rubber pads (supplied with fitting kit)
on the vehicle roof. Pad may vary in shape
to that shown.
●Make sure the pad fits into the holes
underneath the foot.
8
Fitting Kit EN
K983
Fitment
●Clamps directly to edge of roof under the
doors
●Please check the front of this manual for
information relating specifically to your
vehicle.
●Place crossbar on vehicle. Minimum
recommended spacing between the bars is
700mm (27 1/2") (unless otherwise stated).
●Adjust the legs on the crossbar so that they
are positioned equally from the ends of the
crossbar, and the clamps engage firmly on
the body work of the vehicle.
●Tighten adjusting screw to 2 Nm (1.5 ft lb)
hand tight.
9
Fitting Kit EN
K983
●Tighten locking screw on both legs evenly,
2.5 Nm (1.8 ft lb).
●Check crossbar is securely attached to the
vehicle.
●Use keys to fit and lock covers
10
Indice
Altri manuali Prorack Accessori per automobili
Prorack
Prorack K1008 Manuale utente
Prorack
Prorack K545 Manuale utente
Prorack
Prorack K083 Manuale utente
Prorack
Prorack S4 Manuale utente
Prorack
Prorack K982 Manuale operativo e di installazione
Prorack
Prorack K903 Manuale utente
Prorack
Prorack K1213 Manuale utente
Prorack
Prorack K671 Manuale utente
Prorack
Prorack K175 Manuale utente
Prorack
Prorack K004 Manuale utente
Prorack
Prorack K519 Manuale operativo e di installazione
Prorack
Prorack K421 Manuale utente
Prorack
Prorack K618 Manuale utente
Prorack
Prorack K814 Manuale utente
Prorack
Prorack K786 Manuale utente
Prorack
Prorack K1255 Manuale utente
Prorack
Prorack K364 Manuale utente
Prorack
Prorack K746 Manuale utente
Prorack
Prorack K1206 Manuale utente
Prorack
Prorack K766 Manuale utente
