Pullman CB80 Manuale utente
80L WET & DRY
VACUUM CLEANER
3000W (15AMP)
IDEAL FOR:
Shops
Garages
Motels & Hotels
Restaurants & Cafes
CB80
Always switch off the cleaner and remove the plug from the electricity power supply before cleaning
your appliance, when not in use, or attempting any maintenance task. The cleaner must only be
connected to an AC power supply at the voltage shown on the rating label. This cleaner should only
be used for its intended purpose as described in this instruction manual.
1. This appliance is not intended for use by
persons (including children) with reduced
physical, sensory or mental capabilities,
or lack of experience and knowledge
unless they have been given supervision
or instruction concerning the use of the
appliance by a person responsible for their
safety.
2. Children should be supervised to ensure that
they do not play with the appliance.
3. To prevent electrical shock do not immerse
the appliance, power cord or power plug into
water or other liquids.
4. To prevent electrical shock do not use the
vacuum cleaner outdoors.
5. Always check the power cord before use.
The power cord and the plug should be in a
good condition and must not be damaged.
If the power cord is damaged or defective,
it must be replaced by the manufacturer, its
service agent, or similarly qualified persons
in order to avoid a hazard.
6. Do not unplug by pulling on the power cord.
To unplug, grasp the plug not the power
cord. Use only Australian and New Zealand
electrical safety approved extension cords.
7. Do not pull or carry the appliance by the
power cable, use the power cable as a
handle or pull the power cable around
sharp edges or corners. Avoid running the
appliance over the power cable.
8. Ensure the appliance is switched off
before unplugging.
9. Do not handle or operate the appliance
with wet hands, and follow electrical safety
precautions at all times.
10. Extreme caution should be exercised when
using the appliance on stairs.
11. Do not attempt to change the attachments
while the appliance is plugged in to mains
power supply. Switch off and remove
plug from mains power supply. Use only
manufacturer’s recommended accessories.
12. Do not operate the vacuum cleaner too
close to heaters, radiators and other hot
surfaces.
13. Do not use the appliance to pick up
hot water/ liquids, flammable items or
combustible liquids (i.e. petrol, hot ashes
cigarettes, matches, explosive materials or
anything burning) or use in areas where such
substances and items may be present.
14. Do not use the appliance to pick up toxic
materials (i.e. chlorine bleach, ammonia).
15. Ensure the appliance is disconnected from
the main power supply before connecting
the hose to the unit.
16. Do not operate or use the appliance without
dust bag and/or filters in place while dry
vacuum cleaning.
17. Before vacuuming, remove any large or
sharp objects from the floor or cleaning
surface in order to prevent damage to the
filter.
SAFETY PRECAUTIONS AND WARNING:
IMPORTANT
WHEN USING YOUR VACUUM CLEANER BASIC PRECAUTIONS SHOULD ALWAYS
BE OBSERVED, INCLUDING THE FOLLOWING;
2
1. Do not operate the vacuum cleaner too close to heaters, radiators, and other
hot surfaces.
2. Before inserting the plug into the wall, make sure your hand is dry.
3. Before turning on the vacuum cleaner, remove any large or sharp objects from
the floor or cleaning surface in order to prevent damage to the filter.
4. When you want to pull the plug from the wall, do not use the power cable, gently
pull the plug from the power socket.
5. If the hose inlet or telescopic chrome tube are blocked, you should switch off the
cleaner straight away and remove from mains power. Clear the blockage before
attempting to start the vacuum cleaner again.
18. If the hose inlet, floor tool, or the 2 piece
metal tube is blocked, switch off the cleaner
straight away and disconnect from the main
power. Clear the blockage object before
attempting to start the vacuum cleaner again.
19. Do not leave the appliance unattended when
it is connected to a mains power supply.
20. Before carrying out any maintenance service
or cleaning the filters, always switch off the
vacuum cleaner and disconnect the plug
from the power supply.
21. Keep the ends of the hose, telescopic tube
and other openings away from your face
and body.
22. Do not use the vacuum cleaner if it is
damaged or breaks down. Check the
electrical cable regularly for defects. If
cables, hose, electrical contacts
and/or metal tubes are damaged, have
them replaced immediately.
23. Never clean the vacuum cleaner or any
of the electrical parts with water or liquid
cleaners.
24. Never attempt to make any electrical
modifications to the vacuum cleaner.
25. Always store the appliance indoors in a cool
and dry place.
26. Damage caused by improper use or by not
observing the instructions in this manual will
void the warranty.
27. Only plug the machine into a 15amp power
socket.
BEFORE YOU BEGIN
This machine is equipped with a cord and plug. In the event that either of these parts get
damaged, it must be repaired by a qualified technician.
3PULLMAN 80L WET & DRY CB80
KNOW YOUR PRODUCT
12. 13. 15.
1. Lid Handle
2. On/Off Switch
3. Tank
4. Hose Inlet
5. Hose
6. Castor Wheels
7. Drain Hose
8. Cord Holder
9. Connection Latches
10. 2 Piece Metal Tube
11. Carry Handles
12. Dry Pick Up Tool
(hard floor only)
13. Wet Pick Up Tool
14. Crevice Tool
15. Dusting Brush
Technical Information
Model: CB80
240V ~ 50Hz
3000W
10.
11.
9.
8.
2.
1.
3.
4.
5.
6.
7.
14.
4
ASSEMBLY (WITH HOSE)
3. Connect the tube to the desired
cleaning accessory.
4. Connect the hose to the Pullman CB80.
1. Connect the 2-piece metal tube together.
Part 1
2. Connect the handle on the hose to the tube.
5PULLMAN 80L WET & DRY CB80
ACCESSORIES
Fitting dusting brush and crevice tool
To fit the accessories to the 2 piece metal tube,
gently insert the tube into the top of the dusting
brush or crevice tool.
Dusting Brush – ideal for cleaning furniture, curtains
and upholstery
Crevice Tool – ideal for cleaning in tight spaces
Crevice Tool Dusting Brush
Wet Pick Up Floor Tool
The wet pick-up tool is ideal for wet applications.
Dry Pick Up Floor Tool
The dry pick up floor tool is ideal for vacuuming
hard floors.
Do not use the dry pick up floor tool on carpets.
6
OPERATION
Closed
Fit in Place
Before turning on the Pullman CB80 Vacuum Cleaner,
please check that the Drain Hose is secure to the tank
and the cap is fully closed.
2. Ensure the cloth filter bag is always installed before
dry use.
3. Turn the switch of the vacuum cleaner to position “I”.
4. You can determine the suction by using either 1, 2 or
3 motors. Each motor is controlled by a switch located
on the front.
5. Empty the dust tank or dust bag when it’s full or after
each use.
6. The cloth filter also needs to be cleaned accordingly.
IMPORTANT: DISCONNECT THE CLEANER BEFORE CHANGING ACCESSORIES OR TO
EMPTY THE CLEANER.
Dry Vacuum Cleaning
1. Release the connection latches to remove the
canister lid.
7PULLMAN 80L WET & DRY CB80
1. Ensure the cloth filter is removed before the cleaner is
used.
2. Turn the switch of the vacuum cleaner to position “I”.
3. You can determine the suction by using either 1, 2 or
3 motors. Each motor is controlled by a switch located
on the front.
Wet Vacuum Cleaning
OPERATION
4. Empty the tank by the Drain Hose .
5. Empty the tank after each use. Avoid leaving
dust or dirty water in the tank.
6. Wipe the machine inside and out from time to
time, using only lukewarm water.
Before use always examine the power cable for
cuts and/or damage.
7. Wet pick up accessories should be washed
periodically.
open
Remove
8
MAINTENANCE
1. Release the connection latches to remove the
canister lid.
2. Remove the cloth filter.
3. The cloth filter bag can be washed under luke
warm water.
4. Dry by airing for at least 24 hours.
ATTENTION: DISCONNECT FROM MAINS POWER SUPPLY BEFORE DOING ANY
MAINTENANCE WORK. IF PROPER CARE IS TAKEN TO MAINTAIN YOUR CLEANER,
MOTOR MAINTENANCE IS UNNECESSARY. HOWEVER WE RECOMMEND THAT
YOUR CLEANER IS SERVICED ONCE A YEAR.
9PULLMAN 80L WET & DRY CB80
SPECIFICATIONS
TROUBLESHOOTING
TROUBLE POSSIBLE CAUSE REMEDY
Suction weakens or
cleaner runs hot
Clogged filter Brush dirt from filter. If condition
continues, change filter.
Air leak Check all fittings for tight fit (floor tool,
hoses, etc.). Check that tank cover is
sealed properly.
Obstruction in hose
or floor tool
Check floor tool, hose, etc. for
obstructions, and remove if present.
Misting in the exhaust air Saturated filter Replace saturated filter and the
filter mesh.
Watts: 3000W
Capacity: 80L
Power Cable Length: 8m
Net Weight: 26.5kg
10
Questo manuale è adatto per i seguenti modelli
1
Indice
Altri manuali Pullman Aspirapolvere
Pullman
Pullman PV500 Manuale utente
Pullman
Pullman LITHIUM 950 Manuale utente
Pullman
Pullman S20 Manuale utente
Pullman
Pullman WD30BV1 Manuale utente
Pullman
Pullman WD20LSSO Manuale utente
Pullman
Pullman WD60LSSO Manuale utente
Pullman
Pullman PV 14 Manuale utente
Pullman
Pullman A-031b Manuale utente
Pullman
Pullman CB60 Manuale utente
Pullman
Pullman Steam Works SC388L Manuale utente
