PUTCO 85165 Manuale utente
85165, 86165, 87165, 88165
87165L, 88165L
87165L-2, 88165L-2
2011+ FORD SD Bumper Grille Installation Instructions
Please read all instructions before installation and to check to see that all parts are included.
Bumper Grille Installation
1. Remove bumper grille from packaging. Check to see if all parts from above table are included.
2. Remove factory license plate by unhooking the bottom hooks first. Then squeeze the top two clips
to release the license plate from the bumper.
3. From under the vehicle, remove the three plastic clips that hold the rubber flap to the bumper.
Ensure you do not break the plastic clips as you will need them to reinstall the flap when finished.
This will allow for easier installation of the bumper grille later. Fold the flap out of the way. See
Figure 1.
KIT CONTENTS:
Description Qty.
Bumper Grille
1
Alcohol Wipe 1
Only for Lighted Grille (below)
Light Bar (Installed) 1 or 2
Wiring Harness 1
Switch 1
Light Bar Installation Instructions 1
Figure 1
Plasti lips removed
from bumper.
85165, 86165, 87165, 88165
87165L, 88165L
87165L-2, 88165L-2
4. Using the provided alcohol wipe, wipe down all areas that the bumper grille adheres to the Bumper.
Refer to Figure 2.
5. Insert the grille into the bumper starting with the bottom of the grille first. Refer to Figure 3 for
installation
Veiwed from front
Passenger Side of vehi le.
Figure 3
Figure 2
Clean area behind
bumper as shown.
85165, 86165, 87165, 88165
87165L, 88165L
87165L-2, 88165L-2
6. Rotate the grille upwards inserting the two tabs into the holes for the factory license plate. See
Figure 4.
7. Once the tabs are in the license plate holes, place the upper tabs behind the bumper while rolling
the grille into place. The final grille placement will look like Figure 5.
8. Remove the backing from the tape and from the backside of the grille press against the bumper grille
tabs to adhere them to the bumper. Apply firm pressure to all locations for 30 seconds.
9. Fold down tabs inserted into the license plate holes.
10. Reinstall license plate holder and reinsert the three plastic clips for the rubber flap.
11. Do not wash and avoid driving the vehicle for 12-24 hrs to allow the tape to fully adhere to the
bumper.
12. Continue onto wiring instructions if you purchased the lighted grille.
Figure 4
Figure 5
Questo manuale è adatto per i seguenti modelli
7
Indice
Altri manuali PUTCO Accessori per automobili
PUTCO
PUTCO 78102 Manuale utente
PUTCO
PUTCO Hornet Manuale
PUTCO
PUTCO 92009-60 Manuale utente
PUTCO
PUTCO MOLLE PANELS Manuale utente
PUTCO
PUTCO 62129 Manuale utente
PUTCO
PUTCO MOLLE Panels Manuale
PUTCO
PUTCO 92100 Manuale utente
PUTCO
PUTCO MOLLE PANELS RAM 2500 Manuale
PUTCO
PUTCO 11514 Istruzioni per il montaggio
PUTCO
PUTCO HORNET Manuale
PUTCO
PUTCO 470110 Manuale utente
PUTCO
PUTCO HORNET Manuale
PUTCO
PUTCO MOLLE PANELS Manuale utente
PUTCO
PUTCO Molle Panels Manuale
PUTCO
PUTCO 900511 Manuale utente
PUTCO
PUTCO Luminix Manuale utente
PUTCO
PUTCO Venture Tec Rack Manuale
PUTCO
PUTCO LUMINIX Manuale utente
PUTCO
PUTCO HORNET Manuale
PUTCO
PUTCO Boss Bar Manuale utente
