Qian DAYIN80 Manuale utente
THERMAL PRINTER DAYIN80
IMPRESORA TÉRMICA DAYIN 80
MOD. QTM-58306
Please read carefully before using your equipment
and save it for future reference. (Page 2)
Por favor lea cuidadosamente antes de usar su equipo
y guárdelo para uso de futuras consultas. (Página 48)
USER MANUAL / MANUAL DE USUARIO
BLUETOOTH®250mm/s USB AUTOMATIC CUT
CORTE AUTOMATICO
80mm
1
2
About This Manual
Thank you for purchasing the Qian DAYIN 80 thermal and
receipt printer.
This manual can help you learn how to use the product
eciently. Please read it before using the product and keep
it for future reference.
Note
Due to our constant eorts to improve product function and
performance, our company reserves the right to change
the hardware and software specications in the manual
without prior notice.
If you nd any error or omission in the content of this ma-
nual, please contact us for proper advice, thank you very
much.
Without the prior written authorization of our company,
the contents of the corresponding manual attached to the
product must not be reproduced, transmitted, transcribed,
stored, etc.
Statement
This is a type A product, it may cause radio interference in
your environment, if this device causes interference that is
undesirable please consider the use of the product where
it does not interfere with other devices.
3
Safety Precautions
This section presents important information intended to
ensure safe and eective use of this printer.
WARMING:
• Scratch Warning: Never try to touch the auto cutter or
jagged teeth.
• Scald Warning:To avoid been burned, please do not
touch the printer head.
• Shock Warning:Please cut o the power before you
Plug/Unplug the power cable from the printer.
Cautions:
1) Please apply the power adapter to a stable voltage (110-
220V ), please do not use other devices on the same power
outlet to avoid voltage uctuation.
2) Install the printer on a at and stable surface to avoid prin-
ter suered from any vibration and shocks.
3) If water or other liquid spills into the printer, unplug the
power cord immediately and contact your dealer or service
center for advice.
4) Disconnect the power cord if the printer is idle for a long
time.
5) Please ensure the switch button is “o”before you plug the
power cord.
4
6) The printer should only be disassembled or repaired by a
technician.
7) Please strictly follow the recommended use tips of this
manual.
1.Product Information
Main features of the DAYIN 80 thermal printer
• High-quality printing,High-speed and strong stability;
• Interface ( Serial RS232 / RJ45 Ethernet / USB / Blue-
tooth/ WiFi )
• Android device can be supported if connect with USB /
Bluetooth/WiFi methods;
• IOS device can be supported if connect with RJ45
Ethernet / Bluetooth/WiFi method
5
1.1 Technical Parameters and Features
Printer Method
Print Speed
Fonts
Character Size
Extended Character
Table
Logo / Trademark
Interface
Print Command
Roll Width
Roll Diameter
Paper Thickness
Power Supply
Auto Cutter
Codes type
Temperature
Contrast Humidity
Driver
Line Thermal
300mm/sec (80-III type) ;250mm/sec (80-II type)
Simplied Chinese 24x24 point. support GB18030 font
library,support Taiwan and HK traditional(complex font),
Korean and Japanese
576dot/line or 512dot/line ANK Character
Font A:12*24dot,1.5(W)*3.0(H)mm
Font B:9*17dot,1.1(W)*2.1(H)mm
FontC:9*24dot, 1.1(W)*3.0(H)mm
Simplied/Traditional:24*24dot,3.0(W)*3.0(H)mm
OEM437/Katakana/OEM850/OEM860/OEM863/OEM865
WestEurope/Greek/Hebrew/EastEurope/Iran/W-
PC1252/OEM866/OEM852/OEM858/IranII/Latvian/
Arabic/PT151,1251/OEM747
/WPC1257/Vietnam/OEM864/Hebrew/WPC1255/Thai
Download and printing support
Serial / USB / Ethernet / Bluetooth /WIFI( option)
ESC/POS Command
79.5±0.5mm(PrintWidth72mm)
80mm
0.06-0.08 mm
DC24V / 2.5A
Full / Partial Cut
UPC-A / UPC-E / JAN13(EAN13) / JAN8(EAN8) / CODE39 /
ITF / CODABAR / CODE93 / CODE128 / QR CODE
0-45°C
10-80%
Win2000 / Win2003 / Win XP / Win Vista / Win7 / win8 /
win10 / Linux
6
2.Communication Ports
2.1 Universal Serial Bus (USB Port)
Connect the printer with the standard usb cable(usb device
types are automatically) , once printer is connected with the
PC, install the driver , then choose the corresponding port
accordingly.
2.2 RJ45 Ethernet Port (10M/100M) (suitable for 80-III type)
With this port, we can use the network cable and connect
the computer directly, communication and the port number
is 9100;
2.3 RS232 Serial Port
RS-232 is developed according to the EIA standard asyn-
chronous transmission, the specication as following:
• Data transmission: serial interface
• Synchronization: asynchronous
• Signal Level: +5.4V Serial RS232 Level,logic 1:-5.4v, logic
0: +5.4V
• Hardware Flow Control: Hardware
• Baud Rate:9600bps to 115200bps( Optional )
• Data Length: 8 Bits
• 1bit Stop Bit: 1Bit
• Parity: None
The wiring method of the serial interface printer following the
standard rules of Serial Interface EIA standard. Consumer
can get the current default baud rate from “ Print Test Page
”and also can adjust the baud rate via DIP switch ( DIP switch
is on the bottom of the printer )
7
3.Basic Function Operation
3.1 Indicator Light & Printer Status
The printer has 3 Led Indicators( Power / Error and Paper
Out ),Power indicator will lights o n once power is plug-
ged in. And Error Led will lights on when any error arose (
Paper Out / Temperature is too high / mal-position of the
carriage unit on the print head ); We can press the “FEED”
button to test the paper feeding function if the power indi-
cator looks well.
3.2 Printer Operation
• Switch on: Ensure the adapter properly connected with the
printer, press the switch on the “1”position, printer turns on.
• Switch o: Press the switch on the other side “O”.
• Paper Feeding: Press “ FEED” button when powers on,
paper will keep running & stop to run when loosen this bu-
tton.
• Self Printing Test : Switch o the printer then press
“FEED” button and do not release. Press the “POWER”
button at the same time till the “ PAPER OUT” indicator
on, release the button then we can read the current setting
from the test page.
• Hexadecimal printing:Power o the printer, press “FEED”
button & do not release, press “POWER” button at the
same time until the “ PAPER OUT” indicator on, release
the “FEED” button about 3 seconds after the “ PAPER
OUT” indicator o , then the printer run into Hexadecimal
printing model. The way to quit Hexadecimal printing mo-
del is just restart the printer.
8
4.Cleaning Of the Printer
We need to clean the print head if problems as below.
1. Printing is not clear, but thermal paper is ok.
2. Some columns on the printed pages are not clear.
3. Alimentación de papel ruidosa.
Cleaning steps
1. Turn o the power,open the printer cover and take o
the paper roll.
2. We have to wait for a while if we just nished the printing.
3. Use a soft brush or wrung-out ethanol immerged cotton
to clean the print head. Remember to turn on the gear whi-
le lubricating to ensure a completely lubricated;
4. Close the cover once cleaning done and try it later.
Cautions:
Make sure the power of the printer is turned of during the
maintenance.
Hands or other metal tools away from the surface of the
printer head,do not use tweezers to scratch the surface of
the printer head and other sensitive parts.
Do not use gasoline,acetone and other organic solvents
for printer head cleaning.
9
5.Installation Wizard
5.1 Hardware Connection
Ensure all the cables connected correctly( e.g. Adapter /
Interface Cables / RJ-11 cable ) . Open the cover and load
the paper rolls and cartridge ( Paper Loading Direction as
below ).
5.2 Driver Installation
1,Enter the DC driver,click the related les(printer driver
software of 58mm/80mm series)and install.the installation
language will be shown as below.
10
2 - Select the language you need and click the button
”Conrm”,and show the imgae as below,then click the bu-
tton”next step.
3 - Please read the related terms carefully,and install it as
agreement as below
Questo manuale è adatto per i seguenti modelli
1
Indice
Lingue:
Altri manuali Qian Stampante
