QQZM PnP Manuale utente

Updated on 9 Sept., 2014

Manual for PnP IP Camera

--------IPCameraV

This user manual applies to all the QQZM PnP IP Cameras below:

(1) Home Pan-tilt Wireless IP Cameras

(2) Outdoor Wireless Bullet IP Cameras

(3) Dome/ Cube Wireless IP Cameras

NOTICE:

1. Please use Power Adapter and other accessories come with camera

2. Please CHANGE Camera Password and REMEMBER the New One!

Thank you for reading this user manual, if any problems you find out,

please kindly inform us!

Content

1. Hardware Installation......................................................................................... 3

2. Software Installation .......................................................................................... 4

3. Access to Camera.............................................................................................. 5

3.1 Login IP Camera Client....................................................................................................................... 5

3.2 Adding IP Camera Device .................................................................................................................. 6

3.2.1 Using Auto Setting Guide to Add Camera in LAN ........................................................................... 6

3.2.2 Using “Add” Function to Add Camera in LAN................................................................................. 9

3.2.3 Using Context Menu to Add Camera in WAN................................................................................. 9

4. Wi-Fi Setting ..................................................................................................... 10

5. PT and Color Setting.........................................................................................11

5.1 PT Control Panel ..............................................................................................................................11

5.2 Color Control Panel..........................................................................................................................12

5.3 IR-Cut Filter Control.........................................................................................................................12

NOTICE: This Function is jut for which has the IR Cut Filter ............................. 12

6. Record, Snapshot and Two way Audio........................................................... 13

6.1 Operation of alarm, snapshot and two way audio..........................................................................13

6.2 Record onto SD Card........................................................................................................................13

6.3 Schedule Record..............................................................................................................................14

6.4 Setting Picture and video file path ..................................................................................................14

7. Playback Video................................................................................................. 15

7.1 Playback Video Recorded onto Local Computer..............................................................................15

7.2 Remote Playback Video from SD Card............................................................................................. 15

8. Alarm Setting.................................................................................................... 16

8.1 Alarm Introduction ..........................................................................................................................16

8.2 Alarm I/O Description...................................................................................................................... 16

8.3 Motion Detection Description.........................................................................................................17

8.4 Alarm Record...................................................................................................................................18

8.5 Alarm Email ..................................................................................................................................... 19

8.6 Alarm Snapshot ...............................................................................................................................20

9. OSD Setting ...................................................................................................... 21

10. Time Setting...................................................................................................... 22

11. Camera Password and Factory Reset ............................................................ 22

11.1 Password of Camera......................................................................................................................22

11.2 Factory Reset .................................................................................................................................23

11.3 Password of Client Software.......................................................................................................... 23

12. Setup Camera over Smart Phone.................................................................... 24

12.1 Download App...............................................................................................................................24

12.2 Use Smart Phone to Setup Wi-Fi Connection Via AP Function .....................................................24

1.Hardware Installation

Please Connect camera to the Router FIRST and then Power on the camera ,

like the following way:

Use the correct power supply for camera, and connect it to router or switch.

Note: Please check whether the working status of “Network Indicator”and

“Data Indicator”are same with the following description, if not, please

reconnect the power adaptor and network cable again.

(1) P/T Wireless IP Camera Interface Introduction:

(2) Bullet / Dome IP Camera Interface Introduction:

RJ 45

Port

RS485 Port

Audio In, connected to

external microphone

Power

Port

Audio

Output

RJ 45

Port

SD Card

Slot

I/O Port

Power Port

Network Indicator

Data Indicator

Wi-Fi Antenna

2.Software Installation

(1) Insert the CD into CD driver of your PC

(2) It will pop up the auto installation windows like below:

(3) Click the button of “Install CMS Software”to run the install package; or you

can open the CD directly, find out the folder “1. Camera Monitoring

Software2. PC Monitoring Client Software” and install the software” IPC

CMS Software”.

(4) After finishing installation, the icon like below will display on your desktop

Definition

Description

Network Indicator

Orange color, it is always on when power and network cable are connected correctly

Data Indicator

Green color, it is blinking when data is transmitting

3.Access to Camera

3.1 Login IP Camera Client

(1) Double click the icon to login in; you will see the following interface

(2) After click “Login”, you will see the client interface as below:

3.2 Adding IP Camera Device

3.2.1 Using Auto Setting Guide to Add Camera in LAN

The first time running the CMS, setting guide will pop up automatically

(you can click button “Install Wizard” on top right of software on menu

bar);

1. Connect camera to network like the pictures below (Just click “Next”):

2. Click Button “Next (Search Device)”

3. Select the camera and click button “Next (Modify Network Param)”

4. The camera will be added on the left. After successfully adding the

camera, you can also set up the Wi-Fi next step;

5. Select your SSID on the list and input the Password, click “Connect”

6. After about 5-7 seconds, the Wi-Fi connection will be done

3.2.2 Using “Add”Function to Add Camera in LAN

1. Click “Add”button, the cameras connected to LAN will be shown in the list:

2. Tick the camera and click “Add”. The camera will be added into the folder

“Cameras”on the camera list on the left side;

3.2.3 Using Context Menu to Add Camera in WAN

You can use this function to add the cameras in LAN or WAN

2. Tick the Check box

of Cameras that

Connected in LAN

1. Click “Add“Button

3. Click to Add Camera

1. Right Click folder “Device”

2. Click “Add Device through ID”

4.Wi-Fi Setting

4. Click “Next”

6. Click “Finished”

7. Double click the camera

added under the folder of

“Device”, you will see the

video successfully

1. Select the video

of the camera

you want to set

Wi-Fi, right click

the mouse, and

click “Setup”

3. Fill in a name of

camera and any

information you

want to describe it

5. Fill in

Device ID

and

Password

Indice

Altri manuali QQZM Telecamera IP

QQZM

QQZM T5008 Manuale utente

Manuali Telecamera IP popolari di altre marche

FLIR

FLIR Exx series Manuale utente

Avigilon

Avigilon H4A-BO1-IR Manuale utente

Digital Watchdog

Digital Watchdog DWCA-C128-64 Manuale utente

ShareTech

ShareTech AV1 Manuale utente

Ezviz

Ezviz C6C Manuale utente

Melchioni

Melchioni UCAM 2015 Manuale utente

Geutebruck

Geutebruck G-Cam/ESD-4630 Manuale utente

Arecont Vision

Arecont Vision MegaBall AV3146DN-3310-D-LG Manuale utente

Mitel

Mitel 6800i Series Manuale di servizio

Vitek

Vitek VTC-IR403-212NP Manuale utente

THOMSON

THOMSON DSC - 323W Manuale utente

AVer

AVer FB2027 Manuale utente

ENFORCER

ENFORCER EV-T5105-N2SQ Manuale utente

Wansview

Wansview NC543 Manuale utente

Eneo

Eneo MCB-64A0003M0A Manuale utente

deView electronics

deView electronics CBDNI36F Manuale utente

Swann

Swann SwannEye Manuale utente

LevelOne

LevelOne IP CamSecure Manuale utente