Quantum ATL M1500 Manuale utente

Document 6421018-02, Ver. 2, Rel. 0, September 2002 1

Quantum ATL M1500

User’s Guide Addendum —

FC310 Router Option

Introduction 3

Fibre Channel Description ...........................................................................3

FC310 Router Operation...............................................................................3

Key to Successful Configuration of the FC310 Option ............................4

Configuration.................................................................................................4

FC310 Router Option Configuration 4

FC310 Configuration Procedure..................................................................4

Upgrading the FC310 Prism Firmware ......................................................7

Commonly Used FC310 Services Software Commands for the ATL M1500 Library 11

FC310 Services Software Commands 13

FC310 Service Software Operation ...........................................................13

Command Syntax........................................................................................14

List of Abbreviations...................................................................................14

Command Listing........................................................................................14

Quantum ATL M1500 User’s Guide Addendum - FC310 Router Option

Document 6421018-02, Ver. 2, Rel. 0

September 2002

26207947-04fN 10

Quantum ATL M1500 User’s Guide Addendum - FC310 Router Option

Document 6421018-02, Ver. 2, Rel. 0

September 2002

Introduction 3

Introduction 0

The ATL M1500 tape library can contain up to two tape drives and up

to 21 DLT/SDLT cartridges and 25 LTO cartridge. The ATL M1500

library is controlled by a host computer via a SCSI differential bus

using the SCSI-2 medium changer command set. There is also a RS-232

diagnostic port interface.

The ATL M1500 Prism Architecture™ allows for easy conversion from

the SCSI host interface to a Fibre Channel host interface by installing

the FC310 Router option. This document is provided to end users of

the ATL M1500 library to describe the FC310 Fibre Channel host

interface option.

For a complete description of the ATL M1500 library operating

procedures, see the Quantum ATL M1500 User’s Guide (PN 6421000).

Fibre Channel

Description 0

Fibre Channel is a serial data transfer architecture for use with

computers and mass storage devices. Fibre Channel is rapidly

emerging to challenge SCSI as the interface of choice for host-to-

storage applications.

Fibre Channel advantages include:

• Connection distances with the FC310 option of up to 500 meters

• 1 GB/S data transfer rates

• Support for up to 126 devices on a loop

• Support for 24-bit addressing for over 16 million devices in

point-to-point mode or fabric, when using a Fibre Channel switch

or multiple Fibre Channel switches.

• Operating system independence

• Interconnect flexibility

• Fibre Channel fabric switches provide full direct connectivity

between all ports on a network, which can increase the total

throughput of all devices on a network.

FC310 Router

Operation 0

Once the FC310 Router SCSI to Fibre Channel option is installed and

tested, the library operates exactly as a ATL M1500 library with a SCSI

host interface. User operation of the library via the graphical user

interface (GUI) panel is unchanged.

Quantum ATL M1500 User’s Guide Addendum - FC310 Router Option

Document 6421018-02, Ver. 2, Rel. 0

September 2002

4 FC310 Router Option Configuration

Key to Successful

Configuration of the

FC310 Option 0

The FC310 Fibre Channel Option must be configured using the

homebred FC310 Prism Router Services software. The key to

successfully configuring the FC310 Option is to:

• Know exactly how the SCSI cabling in the library is configured

including how many:

aSCSI buses are present in the library

bSCSI devices are connected to each bus

• Use the FC310 Prism Router Services software to create a Map file

identifying which SCSI devices are electrically connected to which

Fibre Channel ports on the FC310 board

Configuration 0This document describes the ATL M1500 configuration procedure with

two tape drives (maximum). To perform this configuration procedure,

proceed to FC310 Router Option Configuration on page 4.

FC310 Router Option Configuration 0

The FC310 Fibre Channel Option must be configured using the FC310

Prism Router Services software.

FC310 Configuration

Procedure 0

The ATL M1500 2-drive FC310 configuration procedure includes the

following steps:

•Confirm the Library’s SCSI Cabling Configuration on page 5

•Connect a Service PC to the Library on page 6

•Start the FC310 Router Services Software on the Library on page 7

•Upgrading the FC310 Prism Firmware on page 7

•Scan the SCSI buses on the Library on page 9

Quantum ATL M1500 User’s Guide Addendum - FC310 Router Option

Document 6421018-02, Ver. 2, Rel. 0

September 2002

FC310 Router Option Configuration 5

Confirm the Library’s SCSI Cabling Configuration 0

1Confirm the SCSI cabling is configured as shown in figure 1.

2If necessary, change the cabling to match figure 1.

Figure 1 ATL M1500 2-

Drive SCSI Cabling

Configuration

Set the SCSI Device Addressing (IDs) for the Library 0

Set the SCSI IDs as shown in table 1.

Table 1 SCSI ID Settings Device SCSI ID

Robotics Controller 0

Drive 0 1

Drive 1 2

Terminator Terminator

Quantum ATL M1500 User’s Guide Addendum - FC310 Router Option

Document 6421018-02, Ver. 2, Rel. 0

September 2002

6 FC310 Router Option Configuration

Connect a Service PC to the Library 0

1Locate the RJ45 connector at the bottom of the FC310 Router board

in the ATL M1500 library as shown in figure 2.

Figure 2 FC310 Mounted

in the ATL M1500

2Connect a 9-pin serial cable (PN 6312122) to the RJ45 connector.

3Connect the opposite end of the serial cable to the comm port on a

service PC. For future reference, take note of which comm port you

used on the service PC.

4Turn on the PC.

5Bring up a terminal emulation program on the PC such as

HyperTerminal or ProComm.

6Set the PC comm port operation as follows:

• Baud rate: 9600

• Data bits: 8

• Stop bits: 1

•Parity:none

• Flow control: none

• Properties/Setting/Function,...keys act as: Windows keys

RJ45

connector

FC310 Board

Quantum ATL M1500 User’s Guide Addendum - FC310 Router Option

Document 6421018-02, Ver. 2, Rel. 0

September 2002

FC310 Router Option Configuration 7

Start the FC310 Router Services Software on the Library 0

1Turn on the library or cycle the library power.

2Upon power-up, the POST output scrolls past the PC screen, as

shown in figure 3, and the Prism Router Services software is

immediately available.

Figure 3 POST Output

Screen

3If the initial screen is not displayed, check the PC comm port

settings, then power cycle the library.

4Press <Enter> when POST completes and Ready displays. The PC is

now in command line mode.

Upgrading the FC310

Prism Firmware 0

If a new version of FC310 firmware is available, use the following

procedure to download the new firmware to the FC310 board:

1Copy the new firmware file to a directory on the service PC.

2Set the FC310 baud rate and the HyperTerminal baud rate to

115200 using the following steps. This speeds the firmware

download process.

Note: Check the version level on the POST output. Verify that

the version is the most recent. If a newer version is

available, download the newer version to the service. For

more information, see Upgrading the FC310 Prism

Firmware on page 7.

Quantum ATL M1500 User’s Guide Addendum - FC310 Router Option

Document 6421018-02, Ver. 2, Rel. 0

September 2002

8 FC310 Router Option Configuration

aAt the Ready prompt type set serialportbaudrate 115200,

then press <Enter>.

bType saveconfiguration, then press <Enter>. Wait for a new

Ready prompt.

cAt the Ready prompt, type:

firmwarerestart<Enter>

dFrom the HyperTerminal menu located at the top of the screen,

select:

Call/Disconnect

eFrom the HyperTerminal menu, select:

File/Properties/Connect To tab/ Configure button

fSet the baud rate to 115200.

gFrom the HyperTerminal menu at the top of the screen, select:

Call/Connect

3At the Ready prompt, type:

saveconfiguration

4Wait for the Ready prompt, then type:

firmwarerestart

5Wait for the Ready prompt, then type:

zmodem receive<Enter>

6From the HyperTerminal menu at the top of the screen, select:

Transfer/Send File

7Browse to the location of the new firmware file.

xxx.IMA

8In the Send File dialog box, select protocol:

zmodem

9Click the Send button. The firmware download begins and takes

approximately 3 to 4 minutes to complete. When the download is

complete a new Ready prompt is displayed on the HyperTerminal

screen.

10 At the Ready prompt, type:

firmwarerestart<Enter>

11 Confirm the new firmware revision is displayed in the

HyperTerminal screen as the software comes to the Ready state.

Wait for the Ready prompt.

12 Reset the FC310 Router and the service PC back to 9600 baud:

Quantum ATL M1500 User’s Guide Addendum - FC310 Router Option

Document 6421018-02, Ver. 2, Rel. 0

September 2002

FC310 Router Option Configuration 9

aAt the Ready prompt, type set serialportbaudrate 9600, then

press <Enter>.

bType saveconfiguration, then press <Enter>.

Wait for a new Ready prompt.

cFrom the HyperTerminal menu (located at the top of the

screen), select Call/Disconnect.

dFrom the HyperTerminal menu select:

File/Properties/Connect To tab/Configure button.

eSet the baud rate to 9600.

fFrom the HyperTerminal menu select Call/Connect.

Scan the SCSI buses on the Library 0

Use the following procedure to confirm that the SCSI buses are cabled

properly.

1Connect the serial cable to the RJ45 connector of the FC310 Router

board in the library.

2Cycle power on the library to start the FC310 Router Services

software.

3At the Ready prompt:

aType scsitargets 0, then press <Enter>. This command scans

and displays all SCSI devices found on SCSI bus 0–the robotics

controller and drive 0.

bType scsitargets 1, then press <Enter>. The SCSI Bus Scan

screen appears as shown in figure 4. Scans bus 1–displays

drive 1.

Quantum ATL M1500 User’s Guide Addendum - FC310 Router Option

Document 6421018-02, Ver. 2, Rel. 0

September 2002

10 FC310 Router Option Configuration

Figure 4 SCSI Targets

Screen

Create the FC310 Prism Map for the FC310 Router in the Library 0

A map file is required for the FC310 Router in the ATL M1500 library.

It is used by the FC310 to identify the SCSI devices in the library

electronically connected to the Fibre Channel port on the board.

To create the FC310 Prism Map, perform the following steps:

1At the screen prompt, type automap 0 and press <Enter>. The

automap command executes.

2When the ready prompt appears, type saveconfiguration and

press <Enter>.

3When the ready prompt appears, type firmwarerestart and press

<Enter>.

Altri manuali per ATL M1500

Indice

Altri manuali Quantum Magazzinaggio

Quantum

Quantum SNC 4000 Manuale di istruzioni

Quantum

Quantum Superloader 3 Manuale utente

Quantum

Quantum Superloader 3 Manuale utente

Quantum

Quantum LTO3 A-Series Manuale utente

Quantum

Quantum Fireball ST Manuale di istruzioni

Quantum

Quantum Scalar i6000 Manuale utente

Quantum

Quantum ATL PowerStor L200 Series Manuale utente

Quantum

Quantum StorNext QD6000 Manuale utente

Quantum

Quantum P1000 Series Manuale utente

Quantum

Quantum DLT-S4 Manuale utente

Quantum

Quantum ActiveScale X100 Manuale utente

Quantum

Quantum DXi9000 Manuale utente

Quantum

Quantum DXi7500 Manuale tecnico

Quantum

Quantum Fireball LCT20 Manuale utente

Quantum

Quantum Scalar i500 Manuale utente

Quantum

Quantum P2000 Series Manuale utente

Quantum

Quantum StorNext QM1200 Manuale utente

Quantum

Quantum DLTtape SDLT 600 Manuale utente

Quantum

Quantum LTO3 A-Series Manuale utente

Quantum

Quantum StorNext QD7000 Manuale utente

Quantum

Quantum DLT 1 Manuale utente

Quantum

Quantum DX3000 Manuale utente

Quantum

Quantum DXi4510 Manuale dell'operatore

Quantum

Quantum DX3000 Manuale utente

Manuali Magazzinaggio popolari di altre marche

QNAP

QNAP TS 32PXU Series Manuale utente

LaCie

LaCie RUGGED RAID Manuale utente

Freecom

Freecom CLS DOCK Manuale utente

PNY

PNY Attache P-FD64MBATT3 Manuale utente

HP StorageWorks MSL2024 Manuale utente

OLT

OLT 6x6 Maximizer Manuale utente

Transcend

Transcend JetFlash 160 Manuale utente

LaCie

LaCie RUGGED MINI Manuale utente

Thunderbolt

Thunderbolt 600 Manuale utente

Panasonic

Panasonic LB-DH8 series Manuale

Intel

Intel RAID High Availability Manuale utente

LaCie

LaCie 12big Thunderbolt 3 Manuale utente

Spectra Logic

Spectra Logic T-Series Spectra T50e Manuale utente

Panasonic

Panasonic LKM-F931-1 Manuale utente

Tabernus

Tabernus Enterprise Erase E2400 Manuale utente

Rocstor

Rocstor COMMANDER 3F series Manuale utente

HP P9000 Manuale utente

Western Digital

Western Digital Ultrastar Data60 Manuale utente