Quantum Scalar i80 Manuale utente
6-68139-01 Rev A, September 2014 *6-68139-01*
© 2014 Quantum Corporation. All rights reserved. Quantum, the Quantum logo, DLT, DLTtape, the DLTtape logo, SuperLoader,
Scalar, DXi, StorageCare, StorNext, GoProtect, and Vision are registered trademarks of Quantum Corporation and its affiliates
in the United States and/or other countries. All other trademarks are the property of their respective owners. Quantum
specifications are subject to change.
Scalar i40 and Scalar i80:
Tape Drive Installation
Quantum recommends that you install tape drives with the library power on. It
is faster and keeps all non-affected drives and partitions active. To do this,
carefully follow the instructions below, to prevent data loss or damage to the
Scalar®i40 or Scalar i80 library.
The tape drive always resides in a drive sled, and together they are effectively
one unit. If you order a new or replacement tape drive, it will already be
installed in a sled.
Caution: Do not remove the tape drive from the drive sled.
Note: For multiple tape drive installs in which you are changing control paths,
install and verify the tape drives one at a time, rather than all at once.
To install a tape drive in the library, refer to the following sections:
•Taking ESD Precautions on page 1
•Installing a Tape Drive on page 2
•Replacing a Tape Drive with a Filler Plate on page 4
Taking ESD Precautions
To avoid damaging static-sensitive parts while performing this procedure,
observe the following precautions:
• Use an antistatic wrist strap. If you do not have one, touch the outside of
the library on the sheet metal before touching any components, to
discharge static from your body.
Quantum Scalar i40/i80: Tape Drive Installation
6-68139-01 Rev A
September 2014
2Installing a Tape Drive
• Keep static-sensitive parts in their original shipping containers until ready
for installation. Look for the ESD sticker to identify static-sensitive parts.
• Avoid touching connectors and other components.
Note: Dry climates and cold-weather heating environments have lower
relative humidity and are more likely to produce static electricity.
Installing a Tape Drive
Tape Drive Slot Location
Considerations
Tape drives can only fit in certain slots, as shown in Figure 1. Slots are numbered
starting from the bottom and moving up.
• Scalar i40: Half-height tape drives can be installed in slots 1 and 2. A full-
height tape drive can be installed in slot 1.
• Scalar i80: Half-height tape drives can be installed in slots 1, 2, 3, 4, and 5.
Full-height tape drives can be installed in slots 1, 3, and 5. The extra space
where slot 6 would be cannot hold a half-height tape drive, but will
accommodate a full-height tape drive installed in slot 5.
Figure 1 Acceptable
Installation Locations for Full-
Height Tape Drives
If possible, it is recommended to start installing the tape drives at the bottom
slot and work up, without leaving spaces between.
Note: If you need to remove one or more filler plates, unscrew the two
thumbscrews securing the filler plate to the back of the library. Holding
the thumbscrews, pull the filler plate gently out of the library. Save the
filler plate in case you need to use it in the future.
Scalar i40 Scalar i80
Quantum Scalar i40/i80: Tape Drive Installation
6-68139-01 Rev A
September 2014
Installing a Tape Drive 3
1Insert the tape drive into the empty drive slot.
The “shelf” on the bottom of the drive sled fits into the notch in the library
chassis and slides on the plastic guide rails (see Figure 2). The tape drive
must be level to slide in smoothly. When the tape drive is correctly inserted,
you will feel a slight “click” as the tape drive sled connector connects into its
mating connector in the library chassis.
Figure 2 Installing a Tape Drive
2Tighten the tape drive’s captive thumbscrews finger tight to secure the tape
drive to the library chassis.
The tape drive LED illuminates red for up to 30 seconds. Then the tape drive
fan starts and the LED turns amber, indicating that the tape drive is offline.
3Connect the tape drive cable from the tape drive to the host.
If the firmware on the newly installed tape drive is different from the
standard configured on the library, the library will automatically autolevel
the new tape drive’s firmware upon installation. (See the
Scalar i40 and
Scalar i80 User’s Guide
for details about tape drive firmware autoleveling).
Autoleveling takes about 7 minutes. A message appears on the Operator
panel, indicating that autoleveling is taking place.
If autoleveling is not required, the tape drive takes about 2 minutes to reach
a ready state.
4If needed, add the new tape drive to an existing partition or create a new
partition for it.
aFrom the Web client, select Setup > Partitions.
bComplete the necessary screens.
Notch in
library
chassis
Drive sled “shelf”
slides in notch
Thumbscrews
Quantum Scalar i40/i80: Tape Drive Installation
6-68139-01 Rev A
September 2014
4Replacing a Tape Drive with a Filler Plate
5Bring the tape drive online, if it is not online already.
aFrom the Operator panel, select Actions > Tape Drive and select
Change Mode.
bSelect the tape drive you want to bring online and press Modify.
cUse the Up button to change the mode to Online, then press Apply.
The tape drive LED turns green.
6Verify the installation by reviewing the Library Configuration report:
aFrom the Web client Reports > Library Configuration.
bMake sure that the new drive is online, in the correct partition, and has
the control path status that you want. You may need to refresh your
Internet browser.
7Verify that the host computer and backup applications can see the new tape
drive configuration correctly.
8If any empty slots remain, install a filler plate in the empty slot (see
Replacing a Tape Drive with a Filler Plate on page 4).
Caution: Filler plates are required to maintain proper library cooling. Do
not run the library with uncovered slots.
9Run the tape drive diagnostic test on the newly installed tape drive to be
sure it is functioning correctly:
aInstall a scratch tape in the top I/E station slot.
bIf manual cartridge assignment is enabled, assign the scratch tape to
the System partition.
cFrom the Operator panel, select Tools > Diagnostics.
dContinue through the next few screens to run the tape drive test on the
replaced tape drive.
If a problem is found during testing, you receive a diagnostic ticket. See the
Scalar i40 and Scalar i80 User’s Guide
for more information about the tape
drive test.
Replacing a Tape Drive with a Filler Plate
The filler plate is half-height in size. If you remove a full-height tape drive, you
must install two filler plates to cover the opening.
1The tape drive filler plate has no “top” or “bottom” orientation – it can go in
either way (see Figure 3on page 5).
2Slide the filler plate into the slot, and tighten the thumbscrews.
Quantum Scalar i40/i80: Tape Drive Installation
6-68139-01 Rev A
September 2014
Replacing a Tape Drive with a Filler Plate 5
Figure 3 Tape Drive Filler Plate
Tape Drive Filler
Plate Captive thumbscrews
Quantum Scalar i40/i80: Tape Drive Installation
6-68139-01 Rev A
September 2014
6Replacing a Tape Drive with a Filler Plate
Questo manuale è adatto per i seguenti modelli
1
Indice
Altri manuali Quantum Magazzinaggio
Quantum
Quantum StorNext QD7000 Manuale utente
Quantum
Quantum SNC 5100 Manuale di istruzioni
Quantum
Quantum Scalar i500 Manuale utente
Quantum
Quantum DLTtape SDLT 600 Manuale utente
Quantum
Quantum DLTtape DLT 8000 Manuale utente
Quantum
Quantum QXS-424 Manuale utente
Quantum
Quantum DX3000 Manuale utente
Quantum
Quantum SuperLoader DLT Manuale utente
Quantum
Quantum Scalar i40 Istruzioni operative e di sicurezza
Quantum
Quantum DLT-V4 Manuale utente
Quantum
Quantum SuperLoader 3A Series Manuale utente
Quantum
Quantum QXS 12G Series Manuale tecnico
Quantum
Quantum Scalar i40 Manuale utente
Quantum
Quantum StorNext AEL500 Manuale utente
Quantum
Quantum DLT Series Istruzioni per l'installazione
Quantum
Quantum DLTtape DLT 2000 Manuale
Quantum
Quantum StorNext QD7000 Manuale di installazione e funzionamento
Quantum
Quantum DPM 5500 Manuale utente
Quantum
Quantum Scalar i40 Manuale utente
Quantum
Quantum ATL M2500 Manuale utente
