RadioLink R6DSM Manuale utente

R6DSM

(FHSS and DSSS spread spectrum)

Radiolink R6DSM, 2.4G 10 channels receiver, DSSS and FHSS spread spectrum working

synchronously, 1 gram weight, SUBS signal, use for Radiolink transmitters AT9, AT9S，AT10 and

AT10II, is the best choice for racing drone.

Two signal working mode:

Red LED always, SBUS signal , 10 channels totally.

How to match code with transmitter:

1. Place the transmitter and the receiver close to each other within 1 meters.

2. Turn on the transmitter, then power on the R6DSM.

3. Connect CH3 of R6DSM to ESC.

4. There is a black button on the R6DSM, press the binding button twice in two seconds and

release, receiver light start blinking, after about 8 times blinking, match code success when

receiver signal LED always on!

Specification:

1) Channels:

10 channels: output 10 channels signal, support SBUS signal, with red LED.

2) Working voltage: 4.8-10V

3) Working current: 38-45mA（input voltage: 5V）

4) Size: 15*13 MM

5) Weight: 1g

6) Detachable antenna

7) 4096 section precision, 0.25us per section, servo anti-shake rudder.

8) Control distance: about 600 meters, actually control distance depends on the environment.

Installment of receiver antenna：

1. The antenna must be kept as straight as possible. Otherwise it will reduce the effective range.

2. Large model aircraft may of some metal part interfering signal; in this case the antennas

should be placed at both sides of the model. Then the best RF signal condition is obtained at any

flying attitude.

3. The antennas must be kept away from conductive materials, such as metal and carbon by at

least a half inch. The coaxial part of the antennas does not need to follow these guidelines, but do

not bend it in a small radius.

4. Keep the antennas away from the motor, ESC, and other noise sources as much as possible.

5. Press and hold the Easy Link (ID SET) one second, now the receiver starts work.

6. After all of the above steps finished, the LED indicator will turn and keep in red.

7. The receiver can be packed by sponge or foam for shocking proof when it is installed to the

model.

After all of the above steps finished, turn off the transmitter and then power it on, now the

program functions to assure it under control of transmitter with a right connection.

Indice

Altri manuali RadioLink Ricevitore

RadioLink

RadioLink R9DS Manuale utente

RadioLink

RadioLink R6DS Manuale utente

RadioLink

RadioLink R9DS Manuale utente

RadioLink

RadioLink R12DSM Manuale utente

RadioLink

RadioLink R7EH-S Manuale utente

RadioLink

RadioLink R8XM Manuale utente

RadioLink

RadioLink R8EF Manuale utente

RadioLink

RadioLink R4FGM Manuale utente

RadioLink

RadioLink R8F Manuale utente

RadioLink

RadioLink R8FG V2.1 Manuale utente

RadioLink

RadioLink R4FGM Manuale utente

RadioLink

RadioLink R4F Manuale utente

RadioLink

RadioLink R6F Manuale utente

RadioLink

RadioLink R6DSM Manuale utente

RadioLink

RadioLink R8FM Manuale utente

RadioLink

RadioLink R10DS Manuale utente

RadioLink

RadioLink R6FG Manuale utente

RadioLink

RadioLink R12DS Manuale utente

RadioLink

RadioLink R7FG Manuale utente

Manuali Ricevitore popolari di altre marche

Garmin

Garmin GA 23 Manuale utente

Aiphone

Aiphone PS-12F Manuale utente

IMES

IMES TCS-01CA-PMI Manuale utente

BWI Eagle

BWI Eagle AIR-EAGLE SR Manuale

AMIMON

AMIMON AMN12310 WHDI Manuale utente

Dual

Dual DMCPA79BT Istruzioni operative

Sound Associates

Sound Associates SA652P Manuale utente

Sherwood

Sherwood NewCastle R-772 Manuale utente

Audio

Audio A10-RX Series Manuale utente

AllSee

AllSee PushShare PSRV1.1 Manuale utente

DEMAG

DEMAG DRC-DR D2 Manuale utente

Teleco

Teleco TVRCL868A02 Manuale utente

Bosch

Bosch RF3222E Manuale utente

Kramer

Kramer 631R Manuale utente

Xpress

Xpress xmc10 Manuale utente

JVC

JVC KD-MR1BTS Manuale utente

Omega Engineering

Omega Engineering UWTC-REC3 Manuale utente

e-survey

e-survey E300 Pro Manuale utente