R&G CP0285 Manuale utente
R&G Racing
Unit 1, Shelley’s Lane, East Worldham, Alton, Hampshire, GU34 3AQ
Tel: +44 (0)1420 89007 Fax: +44 (0)1420 87301 www.rg-racing.com Email: info@rg-racing.com
Page | 1
FITTING INSTRUCTIONS FOR CP0285 CRASH PROTECTORS
HONDA CBR 250R 2011
PICTURE ‘A’ PICTURE ‘B’
REAR OF BIKE FRONT OF BIKE
PICTURE ‘C’
THIS KIT CONTAINS THE ITEMS PICTURED AND LABELLED BELOW.
DO NOT PROCEED UNTIL YOU ARE SURE ALL PARTS ARE PRESENT.
Please note that the way the kit is packed does not necessarily represent the way of
mounting to the bike
Please note that in cases where kits are packed with rubber washers holding the components onto
the bolt –the rubber washers should be thrown away!
R&G Racing
Unit 1, Shelley’s Lane, East Worldham, Alton, Hampshire, GU34 3AQ
Tel: +44 (0)1420 89007 Fax: +44 (0)1420 87301 www.rg-racing.com Email: info@rg-racing.com
Page | 2
THE PARTS SHOWN MAY BE REPRESENTATIVE ONLY (FOR CLARITY OF INSTRUCTIONS ONLY)
LEFT HAND SIDE
1
2
3
9
4
5
6
7
10
2
8
4
R&G Racing
Unit 1, Shelley’s Lane, East Worldham, Alton, Hampshire, GU34 3AQ
Tel: +44 (0)1420 89007 Fax: +44 (0)1420 87301 www.rg-racing.com Email: info@rg-racing.com
Page | 3
THIS KIT CONTAINS THE ITEMS PICTURED AND LABELLED BELOW.
DO NOT PROCEED UNTIL YOU ARE SURE ALL PARTS ARE PRESENT.
RIGHT HAND SIDE
6
7
2
8
9
5
4
10
2
3
1
4
11
R&G Racing
Unit 1, Shelley’s Lane, East Worldham, Alton, Hampshire, GU34 3AQ
Tel: +44 (0)1420 89007 Fax: +44 (0)1420 87301 www.rg-racing.com Email: info@rg-racing.com
Page | 4
TOOLS REQUIRED
Socket set to include 14mm and 17mm sockets and wrench
Set of metric Allen keys 4 and 5mm A/F
Torque wrench (up to 40Nm)
Drill
28mm Hole saw
LEGEND
ITEM 1 = M10x1.25x100mm LONG HEX HEAD BOLTS (CRASH PROTECTOR BOLTS)(x2).
ITEM 2 = M10 PLAIN WASHERS (x4).
ITEM 3 = LW0001 (M12 SHAKE PROOF WASHERS) (x2).
ITEM 4 = M6x40mm LONG CAP HEAD BOLTS (x4).
ITEM 5 = H0016 CLAMP (BOTH SIDES)(x2).
ITEM 6 =M0276 MOUNTING BLOCKS (x2).
ITEM 7 = M10x1.25x90mm LONG HEX HEAD BOLTS (MOUNTING BLOCK BOLTS)(x2).
ITEM 8 = S0388 SPACERS 57.5mm LONG (BOTH SIDES) (x2).
ITEM 9 = B0063 with CS066 (10mm) (BOTH CRASH PROTECTORS) (x2).
ITEM 10 = BC0002 CRASH PROTECTOR CAPS (x2).
ITEM 11 = T0011 MARKING TOOL (60mm LONG) (x1).
ITEM 12 = 100mm LENGTH OF SELF ADHESIVE FOAM (NOT SHOWN) (x2).
PICTURE ‘D’ PICTURE ‘E’
PICTURE ‘F’
R&G Racing
Unit 1, Shelley’s Lane, East Worldham, Alton, Hampshire, GU34 3AQ
Tel: +44 (0)1420 89007 Fax: +44 (0)1420 87301 www.rg-racing.com Email: info@rg-racing.com
Page | 5
Near side (left side as you sit on bike)
Remove side fairing (you will need to disconnect indicators).
Remove the frame bolt in position arrowed in picture ‘D’ (using 14mm socket).
Stick the self-adhesive foam to the mounting surface of the mounting block (it helps prevent
marking of the frame).
Offer one of the mounting blocks (M0276) up to the motorcycle in position shown in picture ‘D’.
Take one of the shorter (90mm long) hex head bolts with washers and locate in the hole in
mounting block and into the frame mount as shown in picture ‘D’.
Do not tighten bolt yet.
Place the frame clamp around frame and aligned with the two clamping hole and secure in position
using two of the M6x40mm long cap head bolts.
Tighten all three bolts evenly.
Fit the marking tool (shown in picture ‘F’) into remaining hole.
Refit the fairing ensuring the marking tool does not impede fairing.
Screw the marking tool out until it contacts inside face of fairing (as shown in picture ‘F’).
Gently push fairing into the marking tool so it leaves a mark on inside of fairing.
Remove fairing.
Drill a pilot hole in fairing (for checking position) from the inside face.
Refit fairing and ensure the pilot hole lines up with marking tool.
If happy with the position remove fairing and the marking tool.
Using the hole saw drill 28mm hole from the outside using the pilot hole as a guide, deburr hole
using a sharp knife or emery paper taking care not to mark outside of fairing.
Refit fairing (connect indicator push fittings).
Slide one of the 10mm washers onto one the longer M10 hexagon headed bolts (100mm long) so
washer sits against head of bolt.
Slide serrated locking washer over the bolt so it sits against washer just fitted.
Next slide the bolt with washers through either crash protector so head of bolt goes into counter-
bore in bobbin.
Next slide one of the spacers over exposed end of bolt so the larger face of spacer sits against the
crash protector.
Offer this assembly through the hole in fairing (ensuring the assembly does not distort the fairing)
up to mounting block and tighten bolt until you feel some compression from inside the protector
using 17mm socket and wrench. PLEASE NOTE THE CRASH PROTECTOR MUST BE
POSITIONED AS IN PICTURE ‘C’ WITH BIGGER END TOWARD FRONT OF BIKE.
Turn a little more so that you feel the compression increase slightly. Then apply a quarter turn.
Do not over tighten as damage can occur to the bike. Do not exceed 40nm of torque.
If not already fitted fit bubble sticker into recess of crash protector cap.
Fit crash protector cap into crash protector.
Off side (right side as you sit on bike)
Remove side fairing (you will need to disconnect indicators).
Remove the frame bolt in position arrowed in picture ‘E’ (using 14mm socket).
Stick the self-adhesive foam to the mounting surface of the mounting block (it helps prevent
marking of the frame).
Offer one of the mounting blocks (M0276) up to the motorcycle in position shown in picture ‘E’.
R&G Racing
Unit 1, Shelley’s Lane, East Worldham, Alton, Hampshire, GU34 3AQ
Tel: +44 (0)1420 89007 Fax: +44 (0)1420 87301 www.rg-racing.com Email: info@rg-racing.com
Page | 6
Take one of the shorter (90mm long) hex head bolts with washers and locate in the hole in
mounting block and into the frame mount as shown in picture ‘E’.
Do not tighten bolt yet.
Place the frame clamp around frame and aligned with the two clamping hole and secure in position
using two of the M6x40mm long cap head bolts.
Tighten all three bolts evenly.
Fit the marking tool (shown in picture ‘F’) into remaining hole.
Refit the fairing ensuring the marking tool does not impede fairing.
Screw the marking tool out until it contacts inside face of fairing (as shown in picture ‘F’).
Gently push fairing into the marking tool so it leaves a mark on inside of fairing.
Remove fairing.
Drill a pilot hole in fairing (for checking position) from the inside face.
Refit fairing and ensure the pilot hole lines up with marking tool.
If happy with the position remove fairing and the marking tool.
Using the hole saw drill 28mm hole from the outside using the pilot hole as a guide, deburr hole
using a sharp knife or emery paper taking care not to mark outside of fairing.
Refit fairing (connect indicator push fittings).
Slide one of the 10mm washers onto one the longer M10 hexagon headed bolts (100mm long) so
washer sits against head of bolt.
Slide serrated locking washer over the bolt so it sits against washer just fitted.
Next slide the bolt with washers through either crash protector so head of bolt goes into counter-
bore in bobbin.
Next slide one of the spacers over exposed end of bolt so the larger face of spacer sits against the
crash protector.
Offer this assembly through the hole in fairing (ensuring the assembly does not distort the fairing)
up to mounting block and tighten bolt until you feel some compression from inside the protector
using 17mm socket and wrench. PLEASE NOTE THE CRASH PROTECTOR MUST BE
POSITIONED AS IN PICTURE ‘C’ WITH BIGGER END TOWARD FRONT OF BIKE.
Turn a little more so that you feel the compression increase slightly. Then apply a quarter turn.
Do not over tighten as damage can occur to the bike. Do not exceed 40nm of torque.
If not already fitted fit bubble sticker into recess of crash protector cap.
Fit crash protector cap into crash protector.
CONSUMER NOTICE
The catalogue description and any exhibition of samples are only broad indications of the Products and R&G may make design
changes which do not diminish their performance or visual appeal and supplying them in such state shall conform to the order. The
Buyer acknowledges no representation or warranty (other than as to title) has been given or will apply to the Products other than those
in R&G’s order or confirmation and the Buyer confirms it has chosen the Products as being of merchantable quality and suitable for
its particular purposes. Where R&G fits the Products or undertakes other services it shall exercise reasonable skill and care and rectify
any fault free of charge unless the workmanship has been disturbed. The Buyer is responsible for ensuring that the warranty on the
motorcycle is not affected by the fitting of the Products. On return of any defective Products R&G shall at its option either supply a
replacement or refund the purchase money but shall not be liable if the Products have been modified or used or maintained otherwise
than in accordance with R&G’s or manufacturer’s instructions and good engineering practice or if the defect arises from accident or
neglect. Other than identified above and subject to R&G not limiting its liability for causing death and personal injury, it shall not be
liable for indirect or consequential loss and otherwise its liability shall be limited to the amounts paid by the Buyer for the Products or
the fitting or service concerned. These terms do not affect the Buyer’s statutory rights.
R&G Racing
Unit 1, Shelley’s Lane, East Worldham, Alton, Hampshire, GU34 3AQ
Tel: +44 (0)1420 89007 Fax: +44 (0)1420 87301 www.rg-racing.com Email: info@rg-racing.com
Page | 7
R&G RACING RETURNS POLICY (NON-FAULTY GOODS)
Returns must be pre-authorised (if not pre-authorised the return will be rejected). Goods may only be returned direct to us if they were
purchased direct from us (customer must prove if necessary). Otherwise to be returned to original vendor. Goods must be in re-
sellable condition, in the opinion of R&G Racing. All returns are subject to a 25% restocking and handling fee (25% of the gross value
exc. P&P –at the prevailing price at time of purchase). The customer must pay any and all carriage charges. No returns of
discontinued products, unless within 14 days of purchase. This policy does not affect your statutory rights and does not refer to faulty
goods.
ISSUE 1 04/05/2011 (NSY)
R&G Racing
Unit 1, Shelley’s Lane, East Worldham, Alton, Hampshire, GU34 3AQ
Tel: +44 (0)1420 89007 Fax: +44 (0)1420 87301 www.rg-racing.com Email: info@rg-racing.com
Page | 1
INSTRUCTIONS DE MONTAGE
CP0285 PROTECTION CARENAGE
HONDA CBR 250R 2011
IMAGE ‘A’ IMAGE ‘B’
ARRIERE DE LA MOTO AVANT DE LA MOTO
IMAGE ‘C’
ASSURER VOUS QUE TOUTES LES PIECES SONT PRESENTES AVANT DE
PROCEDER AU MONTAGE
LA FACON DONT LE KIT EST EMBALLE NE REPRESENTE PAS NECESSAIREMENT LA FAÇON DE
LE MONTER SUR LA MOTO
Notez que dans les cas où les kits sont emballés avec des rondelles en caoutchouc,
composantes du boulon - les rondelles en caoutchouc doivent être jetées !
R&G Racing
Unit 1, Shelley’s Lane, East Worldham, Alton, Hampshire, GU34 3AQ
Tel: +44 (0)1420 89007 Fax: +44 (0)1420 87301 www.rg-racing.com Email: info@rg-racing.com
Page | 2
LES PARTIES EXPOSEES PEUVENT AVOIR UNE VALEUR INDICATIVE
COTE GAUCHE
1
2
3
9
4
5
6
7
10
2
8
4
R&G Racing
Unit 1, Shelley’s Lane, East Worldham, Alton, Hampshire, GU34 3AQ
Tel: +44 (0)1420 89007 Fax: +44 (0)1420 87301 www.rg-racing.com Email: info@rg-racing.com
Page | 3
ASSUREZ VOUS QUE TOUTES LES PIECES SONT PRESENTES AVANT DE
PROCEDER AU MONTAGE
COTE DROIT
6
7
2
8
9
5
4
10
2
3
1
4
11
Indice
Lingue:
Altri manuali R&G Accessori per motociclette
