Ransomes MP653 Manuale utente

United

Kingdom

QUICK START GUIDE

Ransomes MP653 Ride on Rotary Mower With ROPS

STARTING THE ENGINE

SEAT ADJUSTMENT

CONTROLS

DRIVING

MOWING

VISUAL DISPLAY

Refer To The Safety, Operation And Maintenance Manual For Full Operating Instructions.

25097G-GB (rev.0)

RJL 100 May 2015

QUICK START GUIDE

en-2

Ransomes Jacobsen Limited reserves the right to make design changes without obligation to

make these changes on units previously sold and the information contained in this manual is

subject to change without notice.

QUICK START GUIDE

en-3

BEFORE YOU OPERATE FOR THE FIRST

TIME

• Check and adjust tyre pressure, if

necessary, see Safety, Operation and

Maintenance manual.

• If necessary, add diesel fuel to tank.

• Check engine oil and if necessary fill.

• Check the radiator coolant and fill if

necessary (Water with 50% anti-

freeze).

HOW TO START THE ENGINE

The following procedure is for cold engines.

1. Make sure the forward / reverse pedal

(A) is in the neutral position. The cutter

switch (B) is off and the throttle (C) is in

the centre position.

2. Turn the ignition switch (D) to the right

and hold until the engine starts

(approximately 5-10 seconds.)

3. The glow plugs operate automatically.

The time taken for the engine to start,

depends on the temperature of the

coolant

4. When the engine starts, release the key

immediately. The key returns to the

RUN position.

5. If the engine does not start, return the

key to the OFF position and try again.

NOTES

• If the engine does not start after two

tries, wait 20 seconds and try again.

• The starter motor must not be run

continuouslyforlongerthan30seconds

or the starter motor can fail.

• If the red LED’s on the display flash

when you start one of the safety

interlock switches was not set correctly.

HOW TO STOP THE ENGINE

1. Disengage driveto thecutting units with

the cutter switch (B).

2. Returntheforward/reversepedal(A)to

the neutral position.

3. Set the parking brake by pressing the

parking brake switch (E).

4. Move the throttle control lever to the

SLOW position.

5. Turn the ignition key (D) to the OFF

position.

STARTING THE ENGINE

QUICK START GUIDE

en-4

SEAT (GRAMMER MSG85)

Adjustments to the seat can be made for leg

reach, backrest angle and operatorweight to

give a good position to operate the machine.

A. FORWARD AND BACKWARD

ADJUSTMENT

To Adjust

The position of the adjusting lever (A) is on

the right hand side of the seat below the seat

cushion. When moved up, the seat may be

moved backward and forward. When, in the

correct position release the lever into one of

the preset positions.

B. BACKREST ADJUSTMENT

To Adjust

The position of the release lever (B) is on the

left hand side of the seat. While, sitting on

the seat pull the release lever up to release

the backrest. (The backrest is spring loaded

to fold forward to the seat Cushion.) Move

back to get the correct position.

Release the lever to engage in one of the

preset positions.

C. WEIGHT ADJUSTMENT

To Adjust

The position of the operator weight adjust

lever (C) is on the front of the seat. To

change the operator weight setting pull the

lever out. When sitting on the seat rotate the

lever until your weight (kg) is shown in the

window.

D.HEIGHT ADJUSTMENT

To adjust

The height of the seat is adjusted by holding

the edge of the seat cushion, pushing your

weight down and lifting. There are three

preset positions. When the highest has been

achieved the seat returns to its lowest

position.

NOTES

The seat is fitted with a microswitch to sense

the operator in the seat.

Wear the seat belt when a ROPS frame or

ROPS cab are installed.

WARNING

Operator weight adjustment

must be set to ensure the OPC

operates correctly. The parking

brake may automatically be

applied if this operation is not

carried out correctly.

SEAT ADJUSTMENT

QUICK START GUIDE

en-5

STEERING TILT CONTROL

When the operators seat is in the correct

position to operate the traction pedal

comfortably. Push the small foot pedal (A) at

the base of the steering column. Tilt the

column backward or forward to the correct

position. Release the small foot pedal to lock

the steering column in position.

STEERING WHEEL ADJUSTMENT

QUICK START GUIDE

en-6

1234.5

12V

6.6

6.5

12V

10A

CONTROLS

A. Starter Key Switch

B. Throttle Control Lever

C. Parking Brake Switch

D. Deck Lock Switch

E. Cutter Switch

F. Beacon

G. 4 WD In Reverse

H. Cruise Control Switch

J. DPF Inhibit Switch

K. Auxiliary Hydraulic System Kit Switch

L. Light Switch (Optional)

M Hazard Warning Switch

N. Right Side Unit Lift and Lower

P. Centre Unit Lift and Lower

R. Left Side Unit Lift and Lower

S The Cutting Unit is engaged

T Right side cutting unit in cutting

position.

W Centre cutting unit in cutting position.

X Left side cutting unit in cutting position

Y The Weight Transfer

Z. Visual Display

QUICK START GUIDE

en-7

CONTROLS

STARTER KEY SWITCH

Turn the starter key to the right to start the

engine. Release the key to return

automatically to the 'on' position for normal

operation.

NOTE: Before the engine starts, the glow

plugs automatically preheat. The visual

display shows the glow plug symbol and

counter to indicate that the automatic

preheat is in operation.

THROTTLE CONTROL LEVER

The lever is moved away from the operator

to increase the engine speed and toward the

operator to decrease the engine speed.

NOTE: The engine must always be used at

full speed

PARKING BRAKE SWITCH

Move the orange button back and press the

switch to engage the parking brake.

When the engine is stopped, the parking

brake is applied.

To release the parking brake, press the

opposite end of the switch.

The parking brake icon is displayed on

the visual display screen when engaged.

DO NOT apply the brake while the machine

is in motion.

TRANSPORT LOCK SWITCH

Engages the wing unit locks for transport

The parking brake icon is displayed on

the visual display screen when engaged.

QUICK START GUIDE

en-8

HORN BUTTON

For machines without the lighting kit.

The horn button (A) is on the control panel. If

the lighting kit is fitted, the horn is found on

the end of the indicator stalk.

CUTTER SWITCH

To start to cut make sure the speed limiter is

in mow position and the units are lowered.

This switch engages mow speed and cutter

rotation.

To cut grass, push the front of the switch and

move the joysticks forward to lower the

decks.WhenengagedtheyellowLEDonthe

pod is illuminated.

To stop the blade, pushthe rear oftherocker

switch.

When lifted out of work or the operator

leaves the seat, blade rotation is stopped.

BEACON SWITCH

Operates the vehicles rotating beacon

4 WHEEL DRIVE IN REVERSE SWITCH

Engages the four wheel drive while the

vehicle is in reverse. The switch must be

held to engage.

LIGHT SWITCH (OPTIONAL)

Allows manual operation of the road lights.

Position 1. OFF

Position 2. Side / Marker Lights

Position 3. Main Beam.

Note

Position 3 - Will not activate with the ignition

turned OFF.

CONTROLS

QUICK START GUIDE

en-9

CONTROLS

AUXILLARY HYDRAULIC SERVICES KIT

SWITCH (OPTIONAL)

This switch sets the rotary brush or snow

blade to a right side or a left side forward

position.

Push the top of the rocker switch to set a

right side forward position.

Push the bottom of the rocker switch to set a

left side forward position.

CRUISE CONTROL

Usedtoengage thecruisefunctionwhenthe

cutters are engaged.

Automatic mode should be selected to

enable cruise control.

To engage cruise control:

Push the rocker switch to engage the cruise

function.

To disengage cruise control

Push the rocker switch to disengage the

cruise function.

Note. Operation of the transmission pedal,

applying the parking brake and reactivation

of the cruise control switch will deactivate

the cruise control.

DIESEL PATRTICULATE FILTER SWITCH

With the switch in the center position

(default) it allows automatic Active Regen.

Operation of the mower is not changed

during Active Regen.

When the Regen Request light flashes,

press and release the front part of the switch

to start the Parked Regen cycle.

To prevent damage to the turfduring Parked

Regen, park the mower on concrete or

gravel. The engine must be warm, the

traction pedal in NEUTRAL position, PTO

switchinOFFpositionandtheparkingbrake

engagedfortheParkedRegencycletostart.

Do not stop the engine, disengage the

parking brake or drive the mower until the

Regen cycle is completed and the Regen

Request light turns off.

QUICK START GUIDE

en-10

HOW TO DRIVE

• Set the throttle to maximum engine

speed.

• Release the parking brake before you

move in a forward or reverse direction.

• Forward - Carefully press the top of the

Traction pedal to engage forward drive.

• Reverse - Carefully press the bottom of

the Traction pedal to engage reverse

drive.

• To stop - Carefully return the Traction

pedal to the Neutral position.

NOTE

• Use complete foot to operate both forward and reverse.

• Always operate the traction pedal carefully. Do not move the pedal from

forward to reverse quickly.

DRIVING

Altri manuali per MP653

Indice

Altri manuali Ransomes Taglia erba

Ransomes

Ransomes Matador 71 Guida

Ransomes

Ransomes ZT220D Manuale utente

Ransomes

Ransomes Matador Guida

Ransomes

Ransomes HIGHWAY 2130 Guida

Ransomes

Ransomes ZT220D W/61 Manuale utente

Ransomes

Ransomes 51 Super Certes Manuale utente

Ransomes

Ransomes ZE Series Guida

Ransomes

Ransomes Mastiff 91 Guida

Ransomes

Ransomes T-Plex 185 Guida

Ransomes

Ransomes RMP655 Guida

Ransomes

Ransomes 51 Marquis Guida

Ransomes

Ransomes CG161 Specifiche

Ransomes

Ransomes MT503 Guida

Ransomes

Ransomes Parkway 2250 Plus Guida

Ransomes

Ransomes Commander 3510 Guida

Ransomes

Ransomes HR3806 Manuale utente

Ransomes

Ransomes Matador 71 Manuale utente

Ransomes

Ransomes 51 Super Certes Guida

Ransomes

Ransomes HIGHWAY 213 Specifiche

Ransomes

Ransomes MINOR MK. 7 Manuale operativo e di manutenzione

Ransomes

Ransomes Hydrostatic Vergecutter 76 Manuale di servizio

Ransomes

Ransomes Mastiff 91 Guida

Ransomes

Ransomes EC Hydro Midsize Manuale utente

Ransomes

Ransomes MT503 Manuale utente

Manuali Taglia erba popolari di altre marche

RHINO

RHINO 1958 Manuale utente

Wolf Garten

Wolf Garten Compact plus 40 B Manuale utente

Cub Cadet

Cub Cadet LTX 1045 Manuale utente

Craftsman

Craftsman 917.378461 Manuale utente

GGP ITALY SPA

GGP ITALY SPA CR/CS 434 SERIES Manuale utente

Challenge

Challenge CH18V2 Istruzioni operative

TALEN TOOLS

TALEN TOOLS AVR HGM30 Manuale utente

DEWEZE

DEWEZE ATM-725 Manuale operativo

Weed Eater

Weed Eater 180083 Manuale utente

Husqvarna

Husqvarna Poulan Pro PP185A42 Manuale utente

Better Outdoor Products

Better Outdoor Products Quick Series Manuale utente

Cub Cadet

Cub Cadet 23HP Z-Force 60 Manuale operativo

MTD

MTD 795, 792, 791, 790 Manuale utente

Toro

Toro Groundsmaster 3505-D Manuale utente

Dennis

Dennis FT 610 Manuale utente

AIRFORCE

AIRFORCE F-15 Gen 3 Manuale utente

MTD

MTD 126-220-000 Manuale utente

Toro

Toro 74806 Manuale utente