Raspberry Pi CM3+ Manuale utente



Compute Module Development Kit

The Compute Module Development Kit for developing industrial applications

GETTING STARTED

Quick-start guide

Please read this quick-start guide carefully before unpacking the boards from

their anti-static bags or using the kit: it contains important information on how to

avoid damage to the Compute Module and/or the CMIO Board.

Static sensitivity warning

Both the Compute Module and the CMIO board can be damaged by static electricity

(electrostatic discharge or ESD). Please take adequate precautions against static

discharge during handling.

For a complete list of the contents of the development kit, please see the

SPECIFICATIONS tab.

Initial setup and checks

Inserting the Compute Module (CM) into the IO board

First insert the CM at a 45-degree angle, then gently press down on both top corners of

the CM (where the holes are) until it clicks into place.

Checking IO bank voltage jumpers

Please make sure that the two jumpers that power the GPIO bank 0 and 1 voltages are

present on J3, and set to the voltage you wish to use. Do not power up the board if

these jumpers are not attached (and hence the GPIO bank(s) are unpowered), as

this may damage the Module.

Powering up

Make sure the CM is inserted correctly into the socket (J1). Make sure the GPIO banks

are powered (make sure J3 has jumpers present and set correctly). Attach a micro USB

power supply to J2 (POWER IN) to power up the board.

Note that at this point the red power LED and green ACT LED should light up. Nothing

further should happen (because the Compute Module Flash (eMMC) is blank).

Loading an OS image and further documentation

The next step is to write an operating system image to the onboard eMMC Flash. Once

this is done, the board should boot into the OS of your choice when you power up.

Further documentation, including a step by step guide to flashing the eMMC, is

available.

SPECIFICATIONS

The Compute Module Development Kit is made for developing industrial applications

with CM3+, CM3+/Lite, CM3, CM3 Lite, and CM1.

The Development Kit contains the critical hardware that allows you to design the

Compute Module into a custom system, and gives you the freedom to add extra

components and place parts exactly where your product needs them.

The kit includes the Compute Module IO (CMIO) board, which is a simple, open-source

breakout board into which you can plug a Compute Module. The board hosts 120 GPIO

pins, an HDMI port, a USB port, two camera ports, and two display ports.

The Development Kit contains the following:

1 × CMIO v3 breakout board

1 × CM3+/32GB Compute Module

1 × CM3+/Lite Compute Module

1 × CMCDA board (breaks in half to 1 × camera and 1 × display adapter)

2 × 22W, 0.5mm pitch, 50mm length small FFCs for the adapters

1 × USB B to USB A cable (for programming)

4 × pin header female-to-female jumper leads (20cm), to allow connecting display and

camera I2C

Note: a separate power supply, such as the official Raspberry Pi Universal Power

Supply, is required to power the product (not included in the kit).

The CM3+, CM3+/Lite, CM3, CM3 Lite, and CM1 are available for purchase in single

units, or in batches of hundreds or thousands.

COMPIANCE

The Compute Module Development Kit has undergone extensive compliance testing,

and meets the following European standards:

Electromagnetic Compatibility Directive (EMC) 2014/30/EU

Restriction of Hazardous Substances (RoHS) Directive 2011/65/EU

View and download global compliance certificates for Raspberry Pi products.







https://www.raspberrypi.org/products/compute‐module‐development‐kit‐2/2‐1‐19

Indice

Altri manuali Raspberry Pi Microcontrollore

Raspberry Pi

Raspberry Pi RP2040 Manuale utente

Manuali Microcontrollore popolari di altre marche

AMS

AMS AS7261 Demo Kit Manuale utente

Novatek

Novatek NT6861 Manuale utente

Espressif Systems

Espressif Systems ESP8266 SDK Guida all'installazione

Nuvoton

Nuvoton ISD61S00 ChipCorder Guida

STMicrolectronics

STMicrolectronics ST7 Assembler Linker Manuale utente

Texas Instruments

Texas Instruments Chipcon CC2420DK Manuale utente

Lantronix

Lantronix Intrinsyc Open-Q 865XR SOM Manuale utente

NEC

NEC 78GK0S/K 1+ Series Istruzioni per l'installazione e il funzionamento

Mikroe

Mikroe SEMITECH N-PLC Click Istruzioni per l'installazione e il funzionamento

Intel

Intel Agilex Manuale utente

Cypress

Cypress CY4607 HX2VL Manuale utente

DIGITAL-LOGIC

DIGITAL-LOGIC MICROSPACE Manuale utente

Texas Instruments

Texas Instruments TMS320F2837 D Series Manuale utente

CYPRES

CYPRES CY14NVSRAMKIT-001 Manuale utente

Texas Instruments

Texas Instruments INA-DUAL-2AMP-EVM Manuale utente

Espressif Systems

Espressif Systems ESP8266EX Istruzioni operative

Abov

Abov AC33M8128L Manuale utente

Laird

Laird BL654PA Manuale utente