Rave RMC-66A Manuale utente
Installation Manual
RMC-66A
6 Zone 6 Source Audio Matrix with Integrated Amplifier
OGY.COM
WWW.RAVETECHNOLOGY.COM
2
OGY.COM
WWW.RAVETECHNOLOGY.COM
3
OGY.COM
WWW.RAVETECHNOLOGY.COM
Note:
RMC-66K (Optional) Accessory Kit Includes:
•6 Wall Plate Keypads
•1 Wall Plate Keypad Hub
•1 IR Remote Control
•1 Expansion Cable
RMC-66A Matrix Controller Amplifier
Package Contents
INTRODUCTION
The RMC-66A is a functional, easy-to-install, highly compatible, expandable, and user-friendly audio
distribution system. The RMC-66A provides 6 zones stereo or bridged speaker outputs power by class
D integrated amplifier. With optional expansion cables the RMC-66A is expandable up to 18 zones.
This system can be controlled with (optional) Keypads, RS232, IR or with the iOS and Android APP.
Enjoy the quality and reliability of your new RAVE Technology RMC-66A.
FEATURES
•6 Source 6 Zone Audio Matrix with Integrated Amplifier
•Multi-Room Audio Control System Expandable to 18 Zones
•APP Control with Wi-Fi or Ethernet Network Connection
•High Efficiency Class D Amplification
•Stereo or Bridged (mono) Speaker Outputs
•Optional Keypads and IR Remote
•110V or 220V Selectable Power
•RS232 Communication Port
•12V Trigger Inputs and Outputs
•Source 1 Priority PA Function with Trigger Input
•Built In IR Emitters Outputs
•Preamp Outputs Zone 1-3
5
1. Power ON/OFF Switch
2. Zone Status LED
(White: ON - Blue: Standby - Blue/White: Mute)
PRODUCT FEATURES
OGY.COM
WWW.RAVETECHNOLOGY.COM
1. Stereo RCA line level preamp outputs zones 1-3
2. Mode Switch: Stereo or Bridge (mono)
3. Speaker Outputs: Removable terminal block connectors
4. Integrated LAN and Wi-Fi Network
5. 12V Trigger outputs
6. Stereo RCA source inputs (Source 1 priority with PA trigger input)
7. IR Emitter outputs
8. PA trigger input-Mute trigger input-Control trigger output
9. Expansion input and output ports
10. RS232 Communications port
11. Voltage selector switch
12. AC Power connector
13. Keypad Hub RJ45 connector
14. Auto gain control (AGC) on/off switch
15. Unit ID selector switch (Master-Slave1-Slave2)
6
The optional Infrared remote provides zone control through the (IR) receiver
located in the center of the keypad. All keypad functions can be accessed with the
remote. An additional mute button to temporarily mute audio in the zone. The
keypad LED display will flash indicating the mute status. Press the mute button
again to return to un-mute the zone.
OGY.COM
WWW.RAVETECHNOLOGY.COM
KEYPAD AND IR REMOTE FEATURES
The optional keypads can control zone power on/off, volume up/down, selection of
sources 1-6, zone treble, zone bass, zone un-mute and zone standby. The keypads
have Infrared receivers which allows control with optional IR hand held remote. The
IR system can also send IR commands to the IR output jacks of the RMC-66A for
control of your source components.
8
Connect audio sources to the RMC-66A using the 6 stereo RCA inputs on the
rear panel. Input 1 can be used as priority over all inputs. When 12VDC is
applied (3.5mm tip+ sleeve -) to the PA-IN jack, source 1 will be sent to all
zones. This can be used for party mode or paging.
INSTALLATION
OGY.COM
WWW.RAVETECHNOLOGY.COM
CONNECTIONS
9
and APP.
STEREO MODE BRIDGED MODE
The RMC-66A is capable of driving 4-8 ohm speaker loads in stereo mode and 8ohm loads in
bridge (mono) mode. Improper speaker installation can damage the amplifiers and void the
warranty. Use good quality 12-14awg stranded copper speaker wire.
The speaker output terminal block connectors are removable. Remove the terminal block connector
and make sure that all connections are open by turning each set screw counter clockwise. This
insures that the speaker wire opening is completely open. Trim approx 1/4” of insulation from the
speaker wire and twist the copper ends. Insert the speaker wires into the connector and tighten the
set screws. Repeat for the remaining zones.
BRIDGE MODE:
Setting the amplifier mode switch to BRIDGE mode will combine the LEFT and RIGHT signals and
power into one amplifier. The LEFT and RIGHT input signals will be summed to mono. The
minimum speaker impedance in bridge mode is 8ohms.
OGY.COM
WWW.RAVETECHNOLOGY.COM
The RMC-66A has optional POE enabled keypads. This allows for source control from each
specific zone as well as IR routing to the appropriate source devices once selected.
The RMC-66K (Optional Accessory Kit) also comes with a hub that allows for all 6-keypads to
be connected to the amp via Cat5e/6.
10
ZONE-1
ON ON OFF
1 2 3
ZONE-2
ON ONOFF
1 2 3
ZONE-3
ON OFFOFF
1 2 3
ZONE-4
ONONOFF
1 2 3
ZONE-5
ON OFFOFF
1 2 3
ZONE-6
ONOFFOFF
1 2 3
OGY.COM
WWW.RAVETECHNOLOGY.COM
11
FRONT BACK
Expansion Port
OGY.COM
WWW.RAVETECHNOLOGY.COM
CONNECTING THE KEYPAD HUB
Each source has a corresponding Infrared (IR) emitter output. These outputs are
use to control the connected source components remotely through the IR system.
Connect an IR emitter to the output jack and then connect the flasher to the IR
receiver window of the device. Now you can use an IR remote to control your
source through the keypads.
Input Source 2-DVD
IR Output from Source 2
Power
IR Signal
Grounding
IR +
IR -
IR EMITTERS
12
There is also a master control 12VDC trigger output which sends 12VDC to the
CONTROL OUT jack when any zone is powered ON. The 12VDC CONTROL OUT
signal is disengaged when all zones are powered OFF.
PA- IN- Insert 12VDC and Input 1 takes priority over all other inputs and
broadcasts to all 6 zones.
MUTE - IN- Insert 12VDC and all zones will be muted.
WIRING: 3.5mm Mono Plug (Tip + / Sleeve -)
Motorized screen External amplifier
Trigger Inputs and Outputs
OGY.COM
WWW.RAVETECHNOLOGY.COM
Indice
Altri manuali Rave Amplificatore
