Raven SCS 460 Manuale utente
SpraCoupe 3000/4000 with
SCS 460 Console AccuBoom
Installation Manual
Manual No. 016-0171-079 Rev F 01/17 E28992
Copyright 2017
Table of Contents
Manual No. 016-0171-079 Rev F i
Chapter 1 Important Safety Information............................................................................. 1
Important Safety Information .....................................................................................................1
Instructions for Wire Routing .....................................................................................................1
Instructions for Hose Routing ....................................................................................................3
Chapter 2 Introduction............................................................................................................. 5
Introduction ...............................................................................................................................5
Recommendations .................................................................................................................................................................5
Tools Needed ...........................................................................................................................................................................5
Preparing for Installation .....................................................................................................................................................5
Point of Reference .................................................................................................................................................................6
AccuBoom Kit Contents ............................................................................................................6
Chapter 3 AccuBoom Installation.......................................................................................... 7
Install the CAN Power and Ground ...........................................................................................7
Install the AccuBoom Node .......................................................................................................8
Connect the AccuBoom Cable to the Boom Switches ..............................................................9
Install the Master Spray/Hold Switch Wiring ...........................................................................15
Connect the CAN Bus Cable ...................................................................................................16
Install the Logic Power and Ground Connections ...................................................................16
Chapter 4 Section Mapping Setup...................................................................................... 19
Envizio Pro ..............................................................................................................................19
Viper Pro .................................................................................................................................19
Chapter 5 Troubleshooting................................................................................................... 21
Table of Contents
ii SpraCoupe 3000/4000 with SCS 460 Console AccuBoom Installation Manual
CHAPTER
1
Manual No. 016-0171-079 Rev F 1
CHAPTER1
IMPORTANT SAFETY
INFORMATION
IMPORTANT SAFETY INFORMATION
Read this manual and the operation and safety instructions included with your implement and/or controller
carefully before installing the AccuBoom™ system.
• Follow all safety information presented within this manual.
• If you require assistance with any portion of the installation or service of your Raven equipment, contact your
local Raven dealer for support.
• Follow all safety labels affixed to the AccuBoom system components. Be sure to keep safety labels in good
condition and replace any missing or damaged labels. To obtain replacements for missing or damaged safety
labels, contact your local Raven dealer.
When operating the machine after installing AccuBoom, observe the following safety measures:
• Be alert and aware of surroundings.
• Do not operate AccuBoom or any agricultural equipment while under the influence of alcohol or an illegal
substance.
• Remain in the operator’s position in the machine at all times when AccuBoom is enabled.
• Disable AccuBoom when exiting from the operator’s seat and machine.
• Do not drive the machine with AccuBoom enabled on any public road.
• Determine and remain a safe working distance from other individuals. The operator is responsible for disabling
AccuBoom when the safe working distance has diminished.
• Ensure AccuBoom is disabled prior to starting maintenance on AccuBoom or the machine.
INSTRUCTIONS FOR WIRE ROUTING
The word “harness” is used to mean all electrical leads and cables, bundled and unbundled. When installing
harness, secure it at least every 30 cm (12in) to the frame. Follow existing harness as much as possible and use
these guidelines:
Harness should not contact or be attached to:
• Lines and hoses with high vibration forces or pressure spikes
NOTICE
CAUTION
CHAPTER 1
2 SpraCoupe 3000/4000 with SCS 460 Console AccuBoom Installation Manual
• Lines and hoses carrying hot fluids beyond harness component specifications
Avoid contact with any sharp edge or abrading surfaces such as, but not limited to:
• Sheared or flame cut edges
• Edges of machined surfaces
• Fastener threads or cap screw heads
• Ends of adjustable hose clamps
• Wire exiting conduit without protection, either ends or side of conduit
• Hose and tube fittings
Routing should not allow harnesses to:
• Hang below the unit
• Have the potential to become damaged due to exposure to the exterior environment. (i.e. tree limbs, debris,
attachments)
• Be placed in areas of or in contact with machine components which develop temperatures higher than the
temperature rating of harness components
• Wiring should be protected or shielded if it needs to route near hot temperatures beyond harness component
specifications
Harnessing should not have sharp bends
Allow sufficient clearance from machine component operational zones such as:
• Drive shafts, universal joints and hitches (i.e. 3-point hitch)
• Pulleys, gears, sprockets
• Deflection and backlash of belts and chains
• Adjustment zones of adjustable brackets
• Changes of position in steering and suspension systems
• Moving linkages, cylinders, articulation joints, attachments
• Ground engaging components
For harness sections that move during machine operation:
• Allow sufficient length for free movement without interference to prevent: pulling, pinching, catching or
rubbing, especially in articulation and pivot points
• Clamp harnesses securely to force controlled movement to occur in the desired harness section
• Avoid sharp twisting or flexing of harnesses in short distances
• Connectors and splices should not be located in harness sections that move
Protect harnesses from:
• Foreign objects such as rocks that may fall or be thrown by the unit
• Buildup of dirt, mud, snow, ice, submersion in water and oil
• Tree limbs, brush and debris
• Damage where service personnel or operators might step or use as a grab bar
• Damage when passing through metal structures
IMPORTANT: Avoid directly spraying electrical components and connections with high pressure water. High pressure
water sprays can penetrate seals and cause electrical components to corrode or otherwise become
damaged. When performing maintenance:
Manual No. 016-0171-079 Rev F 3
IMPORTANT SAFETY INFORMATION
•Inspect all electrical components and connections for damage or corrosion. Repair or replace
components, connections, or cable as necessary.
•Ensure connections are clean, dry, and not damaged. Repair or replace components, connections,
or cable as necessary.
•Clean components or connections using low pressure water, pressurized air, or an aerosol electrical
component cleaning agent.
•Remove visible surface water from components, connections, or seals using pressurized air or an
aerosol electrical component cleaning agent. allow components to dry completely before
reconnecting cables.
INSTRUCTIONS FOR HOSE ROUTING
The word “hose” is used to mean all flexible fluid carrying components. Follow existing hoses as much as possible
and use these guidelines:
Hoses should not contact or be attached to:
• Components with high vibration forces
• Components carrying hot fluids beyond component specifications
Avoid contact with any sharp edge or abrading surfaces such as, but not limited to:
• Sheared or flame cut edges
• Edges of machined surfaces
• Fastener threads or cap screw heads
• Ends of adjustable hose clamps
Routing should not allow hoses to:
•Hang below the unit
• Have the potential to become damaged due to exposure to the exterior environment. (i.e. tree limbs, debris,
attachments)
• Be placed in areas of or in contact with machine components which develop temperatures higher than the
temperature rating of hose components
• Hoses should be protected or shielded if it needs to route near hot temperatures beyond hose component
specifications
Hoses should not have sharp bends
Allow sufficient clearance from machine component operational zones such as:
• Drive shafts, universal joints and hitches (i.e. 3-point hitch)
• Pulleys, gears, sprockets
• Deflection and backlash of belts and chains
• Adjustment zones of adjustable brackets
• Changes of position in steering and suspension systems
• Moving linkages, cylinders, articulation joints, attachments
• Ground engaging components
For hose sections that move during machine operation:
CHAPTER 1
4 SpraCoupe 3000/4000 with SCS 460 Console AccuBoom Installation Manual
• Allow sufficient length for free movement without interference to prevent: pulling, pinching, catching or
rubbing, especially in articulation and pivot points
• Clamp hoses securely to force controlled movement to occur in the desired hose section
• Avoid sharp twisting or flexing of hoses in short distances
Protect hoses from:
• Foreign objects such as rocks that may fall or be thrown by the unit
• Buildup of dirt, mud, snow, ice, submersion in water and oil
• Tree limbs, brush and debris
• Damage where service personnel or operators might step or use as a grab bar
• Damage when passing through metal structures
•High pressure wash
CHAPTER
2
Manual No. 016-0171-079 Rev F 5
CHAPTER2
INTRODUCTION
INTRODUCTION
Congratulations on your purchase of the Raven AccuBoom system! This system was designed to provide accurate
and cost-efficient application control by avoiding no-spray zones and eliminating wasteful overlaps.
This manual applies to the following machines. For future reference, write the serial number of the machine in the
space below.
MAKE: SpraCoupe
MODEL: 3000/4000 Series
YEAR:
SERIAL NUMBER:
RECOMMENDATIONS
Raven Industries recommends the following best practices when installing the AccuBoom system:
• Use part numbers to identify parts.
• Do not remove the plastic wrap from a part until it is necessary for installation.
• Use recommended cable routing practices:
•Locate available switched and battery power sources before installation.
•Map out the best available cable route before installation.
•Ensure cables are able to rest in a relaxed state and are not pinched, kinked, or stretched.
•Route cables away from moving parts and excessive heat sources.
TOOLS NEEDED
The following tools are recommended for installation of the AccuBoom system:
• SAE standard-sized wrenches
•Cables ties
•Set of tools
PREPARING FOR INSTALLATION
Before installing AccuBoom, park the machine on a clean, level, and dry surface. Leave the machine turned off for
the duration of the installation process.
During the installation process, follow good safety practices. Be sure to carefully read the instructions in this
manual as you complete the installation process.
CHAPTER 2
6 SpraCoupe 3000/4000 with SCS 460 Console AccuBoom Installation Manual
POINT OF REFERENCE
The instructions in this manual assume that you are standing behind the machine, looking toward the cab.
ACCUBOOM KIT CONTENTS
This section contains a list of the components that are included in the AccuBoom kit. Before beginning the
AccuBoom installation, compare the items in the AccuBoom kit with the components on this list. If you have
questions about the kit, contact your local Raven dealer.
IMPORTANT: In addition to the following kit components, an AccuBoom CAN node (P/N 063-0172-316) is required for
the operation of the AccuBoom system. Also, if a CAN system is not currently installed on the machine, a
CAN terminator/power tee kit (P/N 117-0159-923) is required.
TABLE 1. AccuBoom Installation Kit (P/N 117-1004-028)
TABLE 2.
Picture Item Description Part Number Qty.
Not Pictured Manual - SCS 460 Console AccuBoom
Installation 016-0171-079 1
Cable - 6’ CANBus 115-0171-326 1
Cable - SCS 460 Console CAN AccuBoom 115-1001-008 1
H-Driver - 5 Channel 063-0172-753 1
Altri manuali per SCS 460
4
Indice
Altri manuali Raven Controllori
Raven
Raven UltraGlide Autoboom Manuale utente
Raven
Raven AGCO RoGator Hawkeye C Series Manuale utente
Raven
Raven SCS 460 Manuale utente
Raven
Raven AccuBoom Manuale utente
Raven
Raven SmarTrax Manuale utente
Raven
Raven ISO Product Controller II Manuale utente
Raven
Raven SmartTrax Manuale utente
Raven
Raven SmarTrax Manuale utente
Raven
Raven AccuBoom Manuale per l'uso e la cura
Raven
Raven viper Manuale utente
