Raven SmarTrax Manuale utente
CLAAS Lexion 700 Series - Steering
Ready Combine SmarTrax™
Installation Manual
P/N 016-5030-047 Rev. B 09/15 E26478
Copyright 2015
Table of Contents
P/N 016-5030-047 Rev. B i
Chapter 1 Important Safety Information................................................. 1
Hydraulic Safety ........................................................................................................................2
Electrical Safety ........................................................................................................................2
Chapter 2 Introduction............................................................................. 3
Preparing for Installation ...........................................................................................................3
Recommendations ..............................................................................................................4
Point of Reference ...............................................................................................................4
Updates .....................................................................................................................................4
Kit Contents ...............................................................................................................................5
Chapter 3 Wheel Angle Sensor Installation........................................... 9
Assemble the Wheel Angle Sensor (WAS) ...............................................................................9
Single Steering Cylinder Models .........................................................................................9
Dual Steering Cylinder Models ............................................................................................9
Mount the WAS .......................................................................................................................10
Single Steering Cylinder Models .......................................................................................10
Dual Steering Cylinder Models ..........................................................................................12
Chapter 4 Cab Component Installation................................................ 15
Install the SmarTrax Node .......................................................................................................15
Mount the SmarTrax Node ................................................................................................15
Node Mounting Locations ..................................................................................................16
Install the Foot Switch .............................................................................................................16
Install the Road Switch ............................................................................................................17
Install the Node Harness .........................................................................................................18
Install the Valve Harness .........................................................................................................19
Install the Chassis Cable - SmarTrax-Only Systems (If Applicable) ........................................24
Connect SmarTrax to an Existing SmartYield™ Pro (If Applicable) .......................................24
Calibrate the SmarTrax System ..............................................................................................24
System Diagrams ....................................................................................................................25
Table of Contents
ii CLAAS Lexion 700 Series - Steering Ready Combine SmarTrax™ Installation Manual
CHAPTER
1
P/N 016-5030-047 Rev. A 1
C hapt er 1
Important Safety
Information
Read this manual and the operation and safety instructions included with your implement and/or controller
carefully before installing the SmarTrax™ system.
•Follow all safety information presented within this manual.
•If you require assistance with any portion of the installation or service of your Raven equipment, contact
your local Raven dealer for support.
•Follow all safety labels affixed to the SmarTrax system components. Be sure to keep safety labels in good
condition and replace any missing or damaged labels. To obtain replacements for missing or damaged
safety labels, contact your local Raven dealer.
When operating the machine after installing SmarTrax, observe the following safety measures:
•Be alert and aware of surroundings.
•Do not operate SmarTrax or any agricultural equipment while under the influence of alcohol or an illegal
substance.
•Remain in the operator’s position in the machine at all times when SmarTrax is engaged.
•Disable SmarTrax when exiting the operator’s seat and machine.
•Do not drive the machine with SmarTrax enabled on any public road.
•Determine and remain a safe working distance from other individuals. The operator is responsible for
disabling SmarTrax when the safe working distance has diminished.
•Ensure SmarTrax is disabled prior to starting any maintenance work on SmarTrax or the machine.
•When starting the machine for the first time after installing SmarTrax, be sure that all persons stand clear in
case a hose has not been properly tightened.
•The machine must remain stationary and switched off during SmarTrax installation or maintenance.
NOTICE
WARNING
Chapter 1
2 CLAAS Lexion 700 Series - Steering Ready Combine SmarTrax™ Installation Manual
Hydraulic Safety
•Raven Industries recommends that appropriate protective equipment be worn at all times when working on
the hydraulic system.
•Never attempt to open or work on a hydraulic system with the equipment running. Care should always be
taken when opening a system that has been previously pressurized.
•When disconnecting the hydraulic hoses or purging is required, be aware that the hydraulic fluid may be
extremely hot and under high pressure. Caution must be exercised.
•Any work performed on the hydraulic system must be done in accordance with the machine manufacturer’s
approved maintenance instructions.
•When installing SmarTrax hydraulics or performing diagnostics, maintenance, or routine service, ensure
that precautions are taken to prevent any foreign material or contaminants from being introduced into the
machine’s hydraulic system. Objects or materials that are able to bypass the machine’s hydraulic filtration
system will reduce performance and possibly damage the SmarTrax valve.
Electrical Safety
•Always verify that the power leads are connected to the correct polarity as marked. Reversing the power
leads could cause severe damage to the equipment.
•Ensure that the power cable is the last cable to be connected.
CAUTION
CHAPTER
2
P/N 016-5030-047 Rev. B 3
C hapt er 2
Introduction
Congratulations on your purchase of the SmarTrax system! This system is designed to provide cutting-edge,
hands-free steering of the machine via Global Positioning System (GPS) coordinates.
This manual applies to the following machines:
MAKE: CLAAS
MODEL: Lexion 700 Series (Steering Ready) - 730, 740, 750, 760, 770, and 780
FIGURE 1. CLAAS Lexion 760
Preparing for Installation
Before installing the SmarTrax system, park the machine where the ground is level, clean, and dry. Turn off the
machine and leave it turned off for the duration of the installation process.
During the installation process, follow good safety practices. Be sure to carefully read the instructions in this
manual as you complete the installation process.
Chapter 2
4 CLAAS Lexion 700 Series - Steering Ready Combine SmarTrax™ Installation Manual
Recommendations
Raven Industries recommends the following best practices when installing or operating the SmarTrax system
for the first time, at the start of the season, or when moving the SmarTrax system to another machine:
•Install the GPS antenna in the recommended location. Refer to the following table for the machine-specific
antenna mounting location.
•Ensure the machine’s hydraulic filters have been recently changed and there are no issues with the
machine’s hydraulic system (e.g., pump issues, faulty hydraulic motors, fine metal deposits in the hydraulic
hoses, etc.).
•Ensure the machine’s hydraulic system is using fresh oil and debris is flushed from the hydraulic hoses,
valves, and filters.
Raven Industries recommends the following best practices when installing the SmarTrax system:
•Use part numbers to identify the parts.
•Do not remove the plastic wrap from a part until it is necessary for installation.
•Do not remove plastic caps from a part until it is necessary for installation.
Point of Reference
The instructions in this manual assume that you are standing behind the machine, looking toward the cab.
Updates
Software and manual updates are available on the Raven Applied Technology website:
http://www.ravenhelp.com
Machine Preset Antenna X Position
(left to right) Antenna Y Position
(fore/aft offset)
Antenna Z Position
(ground to bottom of
antenna)
Lexion 700 Series Combines Centered 17 ft. /5.181 m 13 ft. 1 in./4.013 m
2
P/N 016-5030-047 Rev. B 5
Introduction
Kit Contents
This section contains a list of the components that are included in the SmarTrax kit. Before beginning the
SmarTrax installation, compare the items in the kit with the components on this list. If you have questions about
the kit, contact your Raven dealer.
At Raven Industries, we strive to make your experience with our products as rewarding as
possible. One way to improve this experience is to provide us with feedback on this manual.
Your feedback will help shape the future of our product documentation and the overall service
we provide. We appreciate the opportunity to see ourselves as our customers see us and are
eager to gather ideas on how we have been helping or how we can do better.
To serve you best, please send an email with the following information to
-CLAAS Lexion 700 Series - Steering Ready Combine SmarTrax™ Installation Manual
-P/N 016-5030-047 Rev. B
-Any comments or feedback (include chapter or page numbers if applicable).
-Let us know how long have you been using this or other Raven products.
We will not share your email or any information you provide with anyone else. Your feedback
is valued and extremely important to us.
Thank you for your time.
TABLE 1. SmarTrax Installation Kit (P/N 117-5030-047)
Picture Item Description Part Number Qty.
Not Pictured Manual - SmarTrax and SmartSteer
Calibration & Operation 016-0171-277 1
Not Pictured Manual - CLAAS Lexion 700 Series
Combines SmarTrax Installation 016-5030-047 1
Node - SmarTrax RTK 063-0173-228 1
Bracket - WAS Mounting 107-0172-030 1
Chapter 2
6 CLAAS Lexion 700 Series - Steering Ready Combine SmarTrax™ Installation Manual
Bracket - Node Mounting 107-0172-055 1
Bracket - Wheel Angle Sensor Mounting 107-0172-300 1
Bracket - 4”-5” Muffler Clamp Wheel Angle
Sensor Mounting 107-0172-431 1
Cable - AutoPilot-Ready Node 115-4001-235 1
Cable - AutoPilot-Ready Valve 115-4001-236 1
Assembly - Foot Switch 063-0172-470 1
Assembly - Road Switch 063-0173-505 1
Assembly - 250 mm 3-Pin Linear Wheel
Angle 063-0181-021 1
Mount - M10 Ball Linear Sensor 103-0001-029 2
Clamp - 1-1/2” U-Bolt Muffler 435-3003-030 1
Clamp - 2” Muffler 435-3003-059 1
TABLE 1. SmarTrax Installation Kit (P/N 117-5030-047)
Picture Item Description Part Number Qty.
Altri manuali per SmarTrax
79
Indice
Altri manuali Raven Controllori
Raven
Raven ISO Product Controller II Manuale utente
Raven
Raven viper Manuale utente
Raven
Raven RCM-Sprayer Hawkeye 2 Manuale utente
Raven
Raven Hawkeye Manuale utente
Raven
Raven AGCO RoGator Hawkeye C Series Manuale utente
Raven
Raven RCM ARAG Bravo Manuale utente
Raven
Raven SCS 460 Manuale utente
Raven
Raven UltraGlide Autoboom Manuale utente
Raven
Raven SmartTrax Manuale utente
Raven
Raven AccuBoom Manuale utente
