RCI CLiK64-TR Manuale utente
1
CLiK64
-
T
R
User Instructions
1. Press the button on the key tag transmitter for at least one
second to transmit the signal code. A red indicator light will
flash for the duration of the transmission. Pressing and
holding the button down only transmits one pulse. This
reduces unintentional transmissions and conserves battery
life.
2. Release and press the button for one second again to send
another transmission.
3. If the light on the transmitter does not light up when you
press and hold any button, replace the battery.
CLiK64
-
T
R
1
CLiK64
-
T
R
2
CLiK64
-
T
R
4
2
1. Carefully pry open the case with a flat edge tool or
screwdriver from the key ring corner.
2. Make sure the case is laid flat on the table upside down.
3. Push the coin shaped battery out of its holder and replace
it with a CR2032 battery being careful to place the “+”
positive side on top.
4. DO NOT install the batteries backwards. The device will be
damaged.
5. Snap close the case
6. Test the transmitter and look for the red LED light to flash
when a button is pressed for one second.
CLiK64
-
T
R
Battery Replacement
3
FCC Regulatory Statements
This device complies with Part 15 of the FCC Rules. Operation
is subject to the following two conditions:
(1) This device may not cause harmful interference.
(2) This device must accept any interference received,
including interference that may cause undesired
operation.
This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to part 15 of the
Federal Communication Commission (FCC) rules. These limits
are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and, if
not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a
particular installation. If this equipment causes harmful
interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by doing one or
more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and
receiver.
Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for
help.
NOTE: THE GRANTEE IS NOT RESPONSIBLE FOR ANY
CHANGES OR MODIFICATIONS NOT EXPRESSLY
APPROVED BY THE PARTY RESPONSIBLE FOR
COMPLIANCE. SUCH MODIFICATIONS COULD VOID THE
USER’S AUTHORITY TO OPERATE THE EQUIPMENT.
4
RF Exposure Warning
This equipment complies with FCC radiation exposure limits set
forth for an uncontrolled environment. This transmitter must not
be co-located or operating in conjunction with any other
antenna or transmitter.
ISED Regulatory Statements
This device complies with ISED Canada license-exempt RSS
standard(s). Operation is subject to the following two conditions:
(1) this device may not cause interference, and (2) this device
must accept any interference, including interference that may
cause undesired operation of the device.
Le présent appareil est conforme avec ISED Canada
applicables aux appareils radio exempts de licence.
L'exploitation est autorisée aux deux conditions suivantes: (1)
l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de
l'appareil doit accepter tout brouillage radioélectrique subi,
même si le brouillage est susceptible d'en compromettre le
fonctionnement.
CAN ICES-3 (B)/NMB-3(B)
RF Exposure Information
This equipment complies with ISED RSS-102 radiation
exposure limits set forth for an uncontrolled environment. This
transmitter must not be co-located or operating in conjunction
with any other antenna or transmitter.
Cet équipement est conforme avec ISED RSS-102 des limites
d'exposition aux rayonnements définies pour un environnement
non contrôlé. Cet émetteur ne doit pas être colocalisé ou
fonctionner en association avec une autre antenne ou émetteur.
Active Secure Inc.
2828 Kingsway Drive, Unit 6
Oakville, Ontario L6J 7M2
Indice
Altri manuali RCI Ricevitore
