RDL D-TPSL1A Manuale utente

TWISTED PAIR FORMAT-A

Models D-TPSL1A, DS-TPSL1A, DB-TPSL1A

Active Single-Pair Sender

Mini-Jack & Stereo RCA In

Stereo Audio Input Combined to Mono Output

Input on Dual RCA Jacks or Mini-Jack

Switch Selects which RJ45 Pair (A, B or C) is Fed

Remote Powering through Twisted Pair Cable

Signal and Power Pair Pass-Through between TP CABLE RJ45 Jacks

Fused Local Power Feeds all Connected Modules

Local Power Input on Terminal Block

Blue LED Indicates Module is Powered

Daisy-Chain with Single-Pair or Two-Pair Format-A Senders

Studio-Quality Precision Active Balanced Circuitry

The D SERIES-TPSL1A modules are single pair audio sending modules compatible with RDL Format-A twisted pair products. These

modules are designed to be mounted in wall boxes, cabinets or other enclosures that allow users to connect audio sources.

APPLICATION: The –TPSL1A modules feature a stereo line input through a mini jack or two RCA phono jacks summed

to mono. The unbalanced inputs are designed to receive standard -10 dBV consumer level signals. These modules drive

only one cable pair, therefore they accept signals and power from other mic-level or line-level Format-A senders. Two other

single-pair senders may be chained with the -TPSL1A, or a single two-pair sender may be connected. If three single-pair

senders are connected together, each sender must feed a different pair: A, B or C. The power pair and all three audio pairs

are fed through both rear-panel RJ45 jacks.

The -TPSL1A may be powered directly from a 24 Vdc power supply using the rear-panel detachable terminal block. Local

power connected to the module is also fed to all connected remote modules. The -TPSL1A may be remotely powered

through the twisted pair cable from any other module, signal distributor or RDL power inserter connected to the same

twisted pair cable. Module power is indicated by a front-panel LED.

RDL FORMAT-A features superior audio performance that rivals or exceeds shielded wiring. Design simplicity, ease of

installation, unsurpassed flexibility, automatic fused power, exceptional hum rejection, low noise, and low distortion provide

designers and installers the optimum choice in economical twisted pair products.

RDL 659 6th St. Prescott, AZ., USA 86301 (928) 443-9391 FAX (928) 443-9392 www.rdlnet.com

D-TPSL1A

DS-TPSL1A

DB-TPSL1A

FORMAT-A TWISTED PAIR

Models D-TPSL1A, DB-TPSL1A, DS-TPSL1A

Format-A Single-Pair Senders

TYPICAL PERFORMANCE

Input: 10kΩunbalanced (left and right)

Input Connection: Mini-jack or dual RCA phono jacks

Input Level: -10 dBV

Format-A Signal Pair Used: Switch-selectable A, B, or C

Format-A Input: RJ45

Output: RDL TP Format-A

Output Connection: RJ45

Frequency Response: 20 Hz to 20 kHz (+/- 0.25 dB)

THD+N: < 0.05% (20 Hz to 20 kHz)

Noise: <-90dB

Headroom: > 18 dB

Indicator: PowerIn

Power Connections (2): Detachable terminal block; RJ45

Power Requirement: 24 Vdc @ 25 mA plus connected loads

Dimensions: 1.6" (4.06 cm) W; 4.11" (10.45 cm) H; 1.89" (4.8cm) D

Mounting Box Minimum Depth: 2.4" (6.1 cm)

Ambient Operating Environment: 0° C to 50° C

EN55103-1 E1-E5; EN55103-2 E1-E4

Typical Performance reflects product at

publication time exclusive of EMC data, if any,

supplied with product. Specifications are

subject to change without notice.

Installation/Operation

STEP 1:Set the pair selection switch to pair A, B or C to select the pair that will be driven. If three single-pair senders are connected together, each sender must feed

a different pair: A, B or C.

STEP 2:Connect 24 Vdc to the power input terminals if this module is not being powered through the twisted pair cable from another module or if this module is

located an excessive distance from the next powered module on the cable. Note: The front-panel power LED will be illuminated if this module is powered. If this

module is powering other modules through the cable and if there is a wiring short, the short must be cleared then power must be turned off to this module for 10

seconds to reset the internal protection circuit.