REITEL ERGORET MINI Manuale utente

Operating Instructions

LABORATORY EQUIPMENT IN

STAINLESS STEEL

ERGORET MINI

REITEL Feinwerktechnik GmbH

Senfdamm 20 | 49152 Bad Essen

Phone: +49(0)5472-9432-0 | Fax: +49(0)5472-9432-40

www.reitel.com | [email protected]

Dear Customer!

The ERGORET MINI table top workstation fits on every worktable and keeps dusts and

gases away from the environment. All work is done behind safety glass on a skin-friendly

beech plate with good visibility through an energy-saving bright work light. The extractor can

be connected to an existing installation or alternatively to the DUSTY extractors.

Any other use or usage beyond this scope is considered unintended use. The manufacturer

shall not be responsible for any damages that may result thereby.

Prior to installation of the device operating instructions and especially the safety instructions

must be read and followed by all personnel who use this device.

After having unpacked the device, please check carefully whether transportation damages of

any kind have occurred. If that is the case, the carrier or manufacturer must be notified within

3 days. The company will not be responsible for any damages found after that.

These operating instructions must be read and followed by all personnel who use this device.

Store it at a safe place near the device. This documentation is protected by copyright.

Transmittal or reproduction of this document in whole or in part and disclosure of its contents

is not permitted. If the operation manual gets lost an extra copy can be ordered from the

manufacturer.

III

INDEX

TECHNICAL DESCRIPTION......................................................................................... 4

BASIC EQUIPMENT....................................................................................................... 4

SPECIAL ACCESSORIES................................................................................................ 4

DEVICE COMPONENTS.................................................................................................. 5

TECHNICAL DATA......................................................................................................... 5

SAFETY NOTES........................................................................................................... 6

GENERAL SAFETY NOTES ............................................................................................ 6

SPECIFIC SAFETY NOTES............................................................................................. 7

INSTALLATION ............................................................................................................ 8

INSTALLATION.............................................................................................................. 8

MOUNT EXTRACTOR..................................................................................................... 8

MOUNTING THE MAGNIFYING GLASS (OPTIONAL)............................................................ 8

OPERATION................................................................................................................. 9

CHRONOLOGICAL RUN OF OPERATION........................................................................... 9

TROUBLESHOOTING .................................................................................................. 9

MAINTENANCE............................................................................................................ 9

WARRANTY.................................................................................................................10

DISPOSAL REGULATIONS ........................................................................................13

SPARE PARTS LIST ...................................................................................................13

EC CONFORMITY DECLARATION.............................................................................14

Technical Description

Basic Equipment

•ERGORET MINI table top workstation

•Filing vice

•Suction connection elbow

Special accessories

•Order-No.: 12900000 Extractor DUSTY MINI

•Order-No.: 17902000 Extractor DUSTY COMFORT

•Order-No.: 24800000 VARIO-Lifting table

•Order-No.: 23205000 Magnifying glass

•Order-No.: 23203000 Extraction adapter for several brands, e.g. Freuding,

Strohm+Maier, KaVo, etc.

Device components

1 Main switch

2 Cover incl. protective film

3 Wood panel

4 Suction tube incl. cap

5 Filing vice

6 Magnifying glass incl. holder and ball joint (optional)

7 LED lamp (inside the cover)

Technical Data

Line voltage

230 V/50–60 Hz

Current consumption

18 W

Height/width/depth

300/490/400 mm

Weight

14 kg

Sound level

≥85 dB(A)

Housing

Stainless steel, wood

Order-No.:

16801000

Made in Germany (Subject to modifications)

Fig.: Device view

Safety Notes

General Safety Notes

•All equipment undergoes final inspection and testing before leaving our factory. However,

if equipment is damaged during shipping or through any other circumstances, it must not

be used in service. Please check the device regularly for damages. Damaged parts

should be replaced immediately.

•All power/air/water/gas sources should be rated for the demands of the device as listed in

the technical data sheets. Maximum ratings must not be exceeded. All VDE (Verein

Deutscher Elektro-Ingenieure) standards should be followed. Equipment should be

grounded according to standards.

•Adherence to valid regulations regarding necessary checks (e.g. according to Accident

Prevention & Insurance or electrical equipment) is exclusively taken over by the

buyer/user of this product.

•This device has been designated to be used only for its intended purpose. All other

applications must be prohibited for safety reasons as otherwise the manufacturer’s

warranty expires.

•The device should be set-up in a clean, well-ventilated room, if necessary under a hood.

•Supporting surfaces should be straight, flat and adequately stable.

•Don’t place anything on top of the machine.

•To avoid injury, appropriate protection should be worn (e.g. gloves, safety glasses, safety

shoes, hearing protection etc.)

•If the machine is defective or working improperly it must be taken out of service. In case

of further use of the machine the owner will be held responsible for any consequential

damage.

•To prevent accidents from water, fire or explosion, all power/air/water/gas sources should

be turned off after working hours and during breaks, and secured against unauthorized

access.

•When carrying out maintenance works or repairs or when opening the device always turn

off the main power switch and unplug the whole unit.

•Repairs should be carried out only by the manufacturer or by qualified and certified

personnel appointed according to chapter 7 –warranty.

•In case of leaking water out of housing or tank shut down device and call service.

•Check all hose connections for leak tightness, if necessary tighten hose clamps again.

Specific Safety Notes

Note:

The protective hood with extraction prevents flying grinding chips. If, nevertheless, the risk

of accidents, e.g. by working with grinding equipment or similar (please note the

manufacturer's instructions), appropriate protective measures must be taken.

Installation

The equipment delivered is ready for immediate use. The sealed plug can be connected

directly to the mains supply 230 V / 16 A. For installation, please refer to chapter 2.

Installation

1. Place the real wood panel (3) in the desired position.

2. Insert the filing vice (5) into the opening provided.

3. Then cover the workplace with the help of the plexiglass hood (2).

Mount extractor

1. Attach the extractor to the suction tube (4) with a suction hose (optional adapter

available) and make the electrical supply.

2. Check the extraction for a tight fit (the extraction can be connected to the front or rear of

the ERGORET MINI.) The unused pipe end must be closed with the sealing cap.

Mounting the magnifying glass (optional)

1. Remove the cap nut in the center of the cover plate.

2. Turn the ball holder onto the thread.

3. Turn the magnifying glass with holder onto the thread of the ball joint. Lock the ball joint

with the locking screw.

Operation

Chronological run of operation

1. Make the electrical connections.

2. Switch on the device via the main switch (1) and then start the extraction.

3. After completing the work switch off the device at the main switch (1) again.

Troubleshooting

Device doesn’t turn on.

Check the building’s main fuse.

LED lamp is defective.

Disconnect the power plug and then

replace the lamp.

Insufficient suction power.

a. Check extraction openings for blockage

(also in the filing vice).

b. Check suction for clogging →replace

filter bag if necessary.

Maintenance

•Check the condition of the device regularly. Pay attention to e.g. visible damage to

housing or power cord.

•Clean the protective cover (2) and the magnifying glass (6) (optional) regularly with a

damp cloth.

•If necessary, replace the LED lamp (7).

•Replace the protective film on the inside of the glass if necessary. (see spare parts list)

Warranty

We, REITEL Feinwerktechnik GmbH, offer a 1 year’s warranty beginning from the proven

date of purchase. This warranty covers all defects traceable to materials, design or

workmanship. The following warranty regulations are applicable:

Within the warranty period Reitel Feinwerktechnik GmbH or an authorized distributor agrees

at its sole option, to perform repair or replace this product at no charge covering all defects

traceable to materials, design or workmanship. Warranty only applies to appropriate use and

regular maintenance of this product according to the operating instructions. Claims under

warranty are restricted to complementary performance. Additional claims, especially claims

for indemnifications, are not covered by this warranty.

Warranty claims have to be addressed to the distributor the product was purchased from or

directly to our service department.

Contact:

REITEL Feinwerktechnik GmbH

Senfdamm 20

49152 Bad Essen

Germany

Phone: +49(0)5472-9432-32 (Service Department)

Phone: +49(0)5472-9432-0 (Reception)

Fax-No: +49(0)5472-9432-40

In case of warranty claim application the sales receipt or your purchase invoice showing the

date of purchase of the product and the serial number must be furnished. Securely pack and

ship the device, freight charges prepaid, at your own risk to us, along with a report describing

the defect. We reserve the right to decline warranty if this information has been removed or

modified after purchase of the product or if they are not included in case of warranty claims.

Warranty repairs have to performed by REITEL Feinwerktechnik GmbH or by authorised

distributors. Repairs performed by non-authorised companies will void the claim for refund

since damages to the product resulting hereof are not covered by warranty.

Indice

Altri manuali REITEL Attrezzature da laboratorio

REITEL

REITEL POLIRET MINI Manuale utente

REITEL

REITEL RETOMAT Series Manuale utente

REITEL

REITEL STAR Manuale utente

REITEL

REITEL ERGORET CC KFO Manuale utente

REITEL

REITEL SANDUBLAST Manuale utente

REITEL

REITEL ROTOGRIND MINI Manuale utente

REITEL

REITEL POLIRET TWIN Manuale utente

REITEL

REITEL SANDUBLAST 3 Manuale utente

REITEL

REITEL SONIRET Manuale utente

REITEL

REITEL RETOMIX MINI Manuale utente

REITEL

REITEL RETOCAST T Manuale utente

REITEL

REITEL SUPERSTEAM Manuale utente

REITEL

REITEL ERGORET CLASSIC Manuale utente

REITEL

REITEL DUSTY COMFORT Manuale utente

REITEL

REITEL ERGORET CC Manuale utente

REITEL

REITEL POLIRET MINI Manuale utente

REITEL

REITEL ROTOGRIND NT Manuale utente

REITEL

REITEL ROTOGRIND NT Manuale utente

REITEL

REITEL RETOMIX COMFORT Manuale utente

REITEL

REITEL Polymat Manuale utente

REITEL

REITEL DUSTY MINI Manuale utente

REITEL

REITEL RETOCAST I Manuale utente

REITEL

REITEL VACURET DIGIT Manuale utente

REITEL

REITEL SANDURET 2 Manuale utente

Manuali Attrezzature da laboratorio popolari di altre marche

Qiagen

Qiagen DML 3000 Manuale utente

Queensgate

Queensgate NANOSCAN OP400 Manuale di programmazione

Conviron

Conviron GEN1000-GE Manuale utente

Parr Instrument

Parr Instrument 4560 Manuale di istruzioni

IKA

IKA IC control Manuale utente

Integra

Integra DOSE IT Manuale utente

Agilent Technologies

Agilent Technologies 5800 ICP-OES Manuale utente

Endress+Hauser

Endress+Hauser Cleanfit CPA875 Manuale utente

NI PXI-5422 Manuale

Collomix

Collomix Aqix Manuale utente

SPEX SamplePrep

SPEX SamplePrep 6875 Freezer/Mill Series Manuale utente

Ocean Insight

Ocean Insight FLAME-NIR+ Manuale utente

Parker

Parker ALIGN-MG-NA Manuale utente

BD 644787 Manuale utente

DENTAURUM

DENTAURUM Compact Megaplus Manuale utente

Biuged Laboratory Instruments

Biuged Laboratory Instruments BGD 626 Manuale utente

VWR

VWR SAS Super IAQ Manuale utente

illumina

illumina MiSeqDx Manuale utente