Renesas RC32012A Manuale utente

Evaluation Kit Manual

R31UH0010EU0102 Rev.1.02 Page 1

The RC32012A evaluation board allows customers to

evaluate Renesas ClockMatrix devices (e.g.,

RC32012A, QFN-72). This document discusses the

following:

▪ The board’s design, its power supply, and jumper

settings

▪ The input and output connectors for normal

operation

▪ How to bring up the board using the Timing

Commander software GUI

▪ How to configure and program the board to

generate standard-compliant frequencies

Kit Contents

The RC32012A EVK ships with the following:

▪ RC32012A Evaluation Board

▪ USB Type-A cable

PC Requirements

▪ Renesas Timing Commander Software installed

▪ ClockMatrix GUI

▪ USB 2.0 or USB 3.0 interface

▪ Windows XP SP3, or later

▪ Processor: Minimum 1GHz

▪ Memory: Minimum 512MB; recommended 1GB

▪ Available Disk Space: Minimum 600MB (1.5GB,

64-bit); recommended 1GB (2GB, 64-bit)

▪ Network access during installation if the .NET

framework is not currently installed on the system

Figure 1. RC32012A Evaluation Board

RC32012A

Evaluation Kit

R31UH0010EU0102 Rev.1.02 Page 2

Apr 20, 2022

RC32012A Evaluation Kit Manual

Contents

1. Board Design . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

1.1 Board Power Supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

1.2 Voltage Selection Jumpers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

1.3 GPIO Switches, LEDs, and Test Points . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

1.4 USB Jack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

1.5 I2C between FTDI, ClockMatrix Device, and On-board EEPROM . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

2. Working with Timing Commander for Programing/Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

2.1 Default Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

2.2 Using Timing Commander to Control the Board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

2.3 Output Terminations and Rework to Take 1PPS Input . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

3. Schematic Diagrams . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Appendix A. How to Upgrade the Firmware . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

4. Ordering Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

5. Revision History . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

R31UH0010EU0102 Rev.1.02 Page 3

Apr 20, 2022

RC32012A Evaluation Kit Manual

1. Board Design

The following diagram identifies the various components of the evaluation board: input and output SMA

connectors, power supply jacks, and some jumper settings necessary for the board operations. Detailed

descriptions are included below.

Figure 2. RC32012A Evaluation Board – Detailed

▪Input SMA connectors – There are five differential inputs labeled CLK0/nCLK0 - CLK4/nCLK4. Each input

clock can be configured differentially (LVDS, PECL 2.5V, and PECL 3.3V) or in single-ended format (CMOS).

▪Output SMA connectors – There are 12 outputs labeled as Q0/nQ0 - Q11/nQ11. Each output clock can be

configured differentially (LVDS, LVPECL, or user-defined amplitude) or in single-ended format (LVCMOS – in-

phase or out-of-phase).

▪GPIO switch, LEDs, and Test points – There are seven GPIOs available. Each GPIO can be set a “low” or

“high” level (if input) or displayed with an LED (if output). Some GPIOs are used to set the chip in a certain

working condition on power-up. For more information, see “Table 18. GPIO Pin Usage at Start-Up” in the

RC32012A Datasheet.

▪USB connector – A USB mini connector connects the evaluation board to a PC for GUI communications. No

power is consumed from the USB connector other than to power the FTDI USB device.

▪VDDQx voltage selection jumpers – Each output voltage can be individually supplied with 1.8V, 2.5V, or 3.3V.

These jumpers are used to select the voltage for the output voltages.

▪Reset button: A small button is used to reset the board.

▪OSCI Input connector – An SMA connector, J45, is provided to optionally supply a clock signal to overdrive

the crystal.

▪OCXO/TCXO Reference (Optional) – An OCXO/TCXO footprint, output at J82. It can be connected to J46

(below) as the reference for System DPLL.

R31UH0010EU0102 Rev.1.02 Page 4

Apr 20, 2022

RC32012A Evaluation Kit Manual

▪SysDPLL Input (Optional) – An SMA connector, J46, is provided to supply a local OCXO/TCXO reference as

an optional reference for System DPLL.

▪Crystal: A crystal of various frequencies must be present for board operations. A 3225 footprint is provided for

SMT crystals. For easy plug-in of a canned crystal, two through-holes are also available.

▪EEPROM – An SO-8 socket is provided to hold an EEPROM device of compatible package. EEROM is used to

store firmware and customer configuration data, if needed.

1.1 Board Power Supply

The evaluation board uses a single +5V supply for its power supplies. When running the board, please set the

bench power supply at 5V/2A. The red jack (J1) is positive; the black jack (J2) is the ground.

Multiple LDOs are used to generate 3.3V, 2.5V, and 1.8V from the +5V supply.

1.2 Voltage Selection Jumpers

There are eight headers/jumpers for selecting different voltages for different functional blocks of the device. Each

header has Pin 1 and 3 labeled in silkscreen – jumping pin 1 and pin 2 will select 3.3V; jumping pin 2 and pin 3 will

select 2.5V. No jumper will have 1.8V.

Please see the following example for JP4 and JP9 – JP4 will select 2.5V, JP9 will select 3.3V.

Figure 3. Example of Voltage Jumpers

The following list shows which head/jumper is used to select a specific voltage:

▪ JP1 – VDDD

▪ JP2 – VDDA

▪ JP3 – VCC_GPIO_DC

▪ JP4 – VDDO_Q8_3_5

▪ JP5 – VDDO_Q2_4_11

▪ JP6 – VDDO_1_10_7

▪ JP7 – VDD_CLK0

▪ JP9 – VDDO_Q0_9_6

R31UH0010EU0102 Rev.1.02 Page 5

Apr 20, 2022

RC32012A Evaluation Kit Manual

Note: VDD_FOD voltage is selected by resistor R908 and R909. In order to prevent damage to the device, both

R908 and R909 should not be stuffed, in which case VDD_FOD = 1.8V.

1.3 GPIO Switches, LEDs, and Test Points

An 8-bit, 3-position dip switch is used to set the logic levels for seven GPIOs (GPIO0-5, GPIO9). The GPIO levels

for each setting and the corresponding LED state are listed in the following table (see picture and labels in

Figure 4).

When the GPIOs are configured as outputs (such as User-Controlled or LOL indicator), the dip switch for the

corresponding GPIO should be placed in the Center position. The LED will indicate the state of the GPIO.

Figure 4. GPIO Setting and Status Display Area

1.4 USB Jack

This is a USB mini connector to the board. The other end of the USB cable is a USB Type A connector going to a

PC.

Table 1. GPIO Settings

Dip Switch Position GPIO Logic Level LED

Left Low On

Center High if GPIO is configured as Input

High or Low according to the GPIO output setting

High if GPIO is configured as Input

High or Low according to the GPIO output setting

Right High Off

R31UH0010EU0102 Rev.1.02 Page 6

Apr 20, 2022

RC32012A Evaluation Kit Manual

1.5 I2C between FTDI, ClockMatrix Device, and On-board EEPROM

One of the major differences between the QFN-72 ClockMatrix device and its BGA-144 counterpart is that there is

only one serial bus on the QFN-72 device. The I2C bus between the FTDI chip and ClockMatrix device is the

same bus between the ClockMatrix device and the on-board EEPROM. The on-board EEPROM is used to store

device firmware and/or customer’s configuration data. JP12 and JP13 must be jumped between Pin 1 and 2 to

enable the I2C connections.

2. Working with Timing Commander for Programing/Configuration

The following sections are best cross-referenced with the ClockMatrix GUI Step-by-Step User Guide that is

available on the ClockMatrix Timing Solutions page and various ClockMatrix device product pages.

2.1 Default Operation

The evaluation board can be operated off EEPROM, which has stored all information including firmware and a

default configuration data. A default operation provides a sanity check on the board before running the board

through the Timing Commander tool. Please set the board to the following default conditions (for jumper and

switch positions, see Figure 5):

▪ Set all the GPIOs to the Center position. This will ensure that GPIO9 is high and that the serial port is

configured for I2C 1-byte addressing.

▪ VDDA = 3.3V, VDD_GPIO_FOD = 1.8V, VDD0_Qx = 3.3V

▪ Crystal frequency 50MHz

▪ CLK0 = 25MHz

▪ FTDI, ClockMatrix device, and EEPROM share the same I2C bus by jumping Pin 1 and 2 of JP12 and JP13

With the above default conditions ready, connect the evaluation board to the PC using a USB cable (type A on the

PC side and mini-type on the board side), and power up the board using a single +5V supply. On power-up, the

ClockMatrix device will read its firmware and configuration data from EEPROM and update all the registers. When

this process completes, the following frequencies are available:

▪ Q0 = 122.88MHz

▪ Q1 = 122.88MHz

Table 2. EEPROM I2C Connections

JP12/JP13 JP12/JP13

Jumper position Pin 1 and 2 Pin 2 and 3

I2C Path FDTI and CM chip;

CM chip and EEPROM

N/A

R31UH0010EU0102 Rev.1.02 Page 7

Apr 20, 2022

RC32012A Evaluation Kit Manual

Figure 5. Board Setting for Default Operation

Note: In order to set GPIO9 to “High”, the switch for GPIO9 must be set either to the “+” (high) position or the

center position.

Before proceeding to communicate to the ClockMatrix device using the Timing Commander GUI, two I2C

connection methods are introduced:

1. Using the on-board FTDI circuit – The evaluation board has on-board FTDI circuitry to translate Timing

Commander access activities from USB to the I2C port of the ClockMatrix device. This is to connect the PC to

the board through the Type-B connector.

2. Using FTDI dongle (C232HM-DDHSL-0 cable) – The dongle has the same FTDI circuit as this board built in it

(see Figure 6). The benefit of using this dongle is to connect to the customer’s board and still enjoy the

debugging capabilities that Timing Commander has to offer.

R31UH0010EU0102 Rev.1.02 Page 8

Apr 20, 2022

RC32012A Evaluation Kit Manual

Figure 6. FTDI Dongle: USB Type-A at PC end and 10 Free-wires at the other end

The free wires are color-coded and numerically indexed as displayed in the following picture.

When using with Timing Commander, only four wires are used. When connecting to a customer board, connect

the Orange wire to SCL; tie the Yellow wire and Green wire together and connect to SDA; then, importantly,

connect the Black ground wire to the customer’s board GND. Assuming there is a pull-up resistor for SCL and

SDA, respectively, on customer board.

By using FTDI dongle, we can connect to a customer board and use the Timing Commander GUI just like working

on a ClockMatrix evaluation board. When using the FTDI dongle to connect to a customer board, in Timing

Commander “Connection Settings” window, “On-board USB (SPI)” is selected in Connection Interface box (see

Figure 10), same as connecting to a Renesas evaluation board.

Color Pin Number Name Type Description

Orange 2 SCL Output Serial Clock

Yellow 3 SDA Input/Output Serial data signal shorted together to

create bidirectional data (both yellow

and green wires must be shorted

together)

Green 4

R31UH0010EU0102 Rev.1.02 Page 9

Apr 20, 2022

RC32012A Evaluation Kit Manual

2.2 Using Timing Commander to Control the Board

Once the default operation is successful, complete the following steps using Timing Commander to configure and

program the ClockMatrix device as per your application requirements.

1. Power up the board and set the main serial port in I2C mode by GPIO9 = “high”. See Figure 5 for the GPIO9

position. Connect the board to PC.

2. Start the Timing Commander software.

You will see options of “New Setting File” and “Open Setting file”. For a new configuration, select “New Setting

File”

Figure 7. Starting Up Timing Commander GUI

R31UH0010EU0102 Rev.1.02 Page 10

Apr 20, 2022

RC32012A Evaluation Kit Manual

3. After selecting “New Settings File”, a device selection window will appear. In the window, choose the intended

device in the list (RC32012A is selected in this example).

Click the button at the lower right corner of the window (red circle) to browse and select the correct personality

file (in this example, personality Version 10.0.1 is selected), then click OK.

Figure 8. Selecting RC32012A using Personality File Version 10.0.1

Indice

Altri manuali Renesas Hardware per computer

Renesas

Renesas 9FGV100 Series Manuale utente

Renesas

Renesas M32182T2-PTC Manuale utente

Renesas

Renesas M37630T-RFS Manuale utente

Renesas

Renesas H8SX/1650 Manuale utente

Renesas

Renesas H8S/2319 series Manuale utente

Renesas

Renesas H8S series Manuale utente

Renesas

Renesas M16C Series Manuale utente

Renesas

Renesas RX13T Manuale utente

Renesas

Renesas Emulation Pod M306H2T-RPD-E Manuale utente

Renesas

Renesas Emulation Pod M306H7T3-RPD-E Manuale utente

Renesas

Renesas V850ES/KG2 Manuale utente

Renesas

Renesas RS-485 Manuale utente

Renesas

Renesas M30280T-85LGF Manuale utente

Renesas

Renesas R8C series Manuale utente

Renesas

Renesas RX72M Series Manuale utente

Renesas

Renesas FP-80A Manuale utente

Renesas

Renesas M3T-FLX-DMY613 Manuale utente

Renesas

Renesas RX Family Manuale utente

Renesas

Renesas H8S/2500 Series Manuale utente

Renesas

Renesas H8S/2628 Manuale utente

Renesas

Renesas SKP16C26 StarterKit Plus Manuale utente

Renesas

Renesas H8 Series Manuale utente

Renesas

Renesas VersaClock7 PCB Manuale di istruzioni

Renesas

Renesas YRBRL78G14 Manuale utente

Manuali Hardware per computer popolari di altre marche

EMC2

EMC2 VNX Series Manuale del proprietario

Panasonic

Panasonic DV0PM20105 Manuale utente

Mitsubishi Electric

Mitsubishi Electric Q81BD-J61BT11 Manuale utente

Gigabyte

Gigabyte B660M DS3H AX DDR4 Manuale utente

Raidon

Raidon iT2300 Manuale utente

National Instruments

National Instruments PXI-8186 Manuale utente

Hauppauge

Hauppauge WinTV-HVR-2250 Manuale utente

Kontron

Kontron CP6002 Manuale utente

Manhattan

Manhattan 702843 Manuale utente

Aphex

Aphex 230 Manuale utente

AMD

AMD Phenom II Manuale operativo

Intel

Intel NUC 12 Pro Manuale utente

dbx

dbx Zone Pro 1260 Manuale utente

Galaxy

Galaxy GHDX2-2430S-24F4D Manuale utente

Intel

Intel AXXRMFBU4 Manuale utente

Kontron

Kontron DIMM-PC/MD Manuale utente

ST X-NUCLEO-SAFEA1B Istruzioni operative

STEINWAY LYNGDORF

STEINWAY LYNGDORF SP-1 Manuale utente